For coping with bad keyboards, permit to type a braille pattern by
pressing several chords. By default, only one chord is needed.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Providing more accurate coordinates for thumb press requires additional
steps in the filtering logic:
- Ignore samples found invalid by the debouncing logic, or the ones that
have out of bound pressure value.
- Add a parameter to repeat debouncing, so that more then two consecutive
good readings are required for a valid sample.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
X touchscreen drivers that don't interpret the designated pen up message
assume a pen up event from a pressure value 0. For these we generate a
pressure 0 message along with the pen up message.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The pen down IRQ will toggle during each X,Y,Z measurement cycle.
Even though the IRQ is disabled it will be latched and delivered
when after enable_irq. Thus in the IRQ handler we must avoid
starting a new measurement cycle when such an "unwanted" IRQ happens.
Add a get_pendown_state platform function, which will probably
determine this by reading the current GPIO level of the pen IRQ pin.
Move the IRQ reenabling from the SPI RX function to the timer. After
the last power down message the pen IRQ pin is still active for a
while and get_pendown_state would report incorrectly a pen down state.
When suspending we should check the ts->pending flag instead of
ts->pendown, since the timer can be pending regardless of ts->pendown.
Also if ts->pending is set we can be sure that the timer is running,
so no need to rearm it. Similarly if ts->pending is not set we can
be sure that the IRQ is enabled (and the timer is not).
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
- Add disable attribute to support device locking mode where
unintentional touch event shouldn't wake up the system;
- Update comments;
- Add missing spin_lock_init;
- Do device resume with the lock held;
- Do cleanup calls / free memory in the reverse order of initialization.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Sometimes a polling loop had a hard time changing state without
pre-emption enabled. Use msleep instead, it's better anyway.
Signed-off-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some touchscreens seem to oscillate heavily for a while after touching
the screen. Implement support for sampling the screen until we get two
consecutive values that are close enough.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Submit a seperate request for powering down the ADC in ads7846,
doing it after the last read request. Otherwise some of the read
values are incorrect.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It's handy for userspace diagnostics to see the pen down status, to
see whether the touchscreen is "stuck" (shortcircuited).
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
- Add KEY_BRL_* input keys and K_BRL_* keycodes;
- Add emulation of how braille keyboards usually combine braille dots
to the console keyboard driver;
- Add handling of unicode U+28xy diacritics.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Toshiba Protege M300 also requires the same workaround as Satellites
and Dynabooks - Synaptics report rate should be lowered to 40pps
(from 80), otherwise KBC starts losing keypresses.
Signed-off-by: Richard Thrippleton <ret28@cam.ac.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
SNES gamepads and mice share the same type of interface so they both can be
connected to the parallel port using a simple interface. Adding mouse
support to a gamepad driver may sound funny at first, but doing so in this
case makes it possible to connect and SNES gamepads and mice at the same
time, on the same port.
Signed-off-by: Raphael Assenat <raph@raphnet.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
sysfs can't handle more than PAGE_SIZE data coming from attributes'
show() methods; make sure we respect this limit.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3424/2: ixp23xx: fix uncompress.h for recent CRLF decompressor change
[ARM] 3434/1: pxa i2s amsl define
[ARM] 3425/1: xsc3: need to include pgtable-hwdef.h
[ARM] Allow un-muxed syscalls to be available for everyone
[ARM] 3420/1: Missing clobber in example code
[ARM] nommu: fixups for the exception vectors
[ARM] nommu: add nommu specific Kconfig and MMUEXT variable in Makefile
[ARM] nommu: start-up code
[ARM] nommu: MPU support in boot/compressed/head.S
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Avoid "u64 foo : 32;" for gcc3 vs. gcc4 compatibility
[IA64] Export cpu cache info by sysfs
* master.kernel.org:/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] Fix typo in earlier cifs_unlink change and protect one
[CIFS] Incorrect signature sent on SMB Read
[CIFS] Fix unlink oops when indirectly called in rename error path
[CIFS] Fix two remaining coverity scan tool warnings.
[CIFS] Set correct lock type on new posix unlock call
[CIFS] Upate cifs change log
[CIFS] Fix slow oplock break response when mounts to different
[CIFS] Workaround various server bugs found in testing at connectathon
[CIFS] Allow fallback for setting file size to Procom SMB server when
[CIFS] Make POSIX CIFS Extensions SetFSInfo match exactly what we want
[CIFS] Move noisy debug message (triggerred by some older servers) from
[CIFS] Use correct pid on new cifs posix byte range lock call
[CIFS] Add posix (advisory) byte range locking support to cifs client
[CIFS] CIFS readdir perf optimizations part 1
[CIFS] Free small buffers earlier so we exceed the cifs
[CIFS] Fix large (ie over 64K for MaxCIFSBufSize) buffer case for wrapping
[CIFS] Convert remaining places in fs/cifs from
[CIFS] SessionSetup cleanup part 2
[CIFS] fix compile error (typo) and warning in cifssmb.c
[CIFS] Cleanup NTLMSSP session setup handling
extra path.
Since cifs_unlink can also be called from rename path and there
was one report of oops am making the extra check for null inode.
Signed-off-by: Steve French <sfrench@us.ibm.com>
Fixes Samba bug 3621 and kernel.org bug 6147
For servers which require SMB/CIFS packet signing, we were sending the
wrong signature (all zeros) on SMB Read request. The new cifs routine
to do signatures across an iovec was not complete - and SMB Read, unlike
the new SMBWrite2, did not fall back to the older routine (ie use
SendReceive vs. the more efficient SendReceive2 ie used the older
cifs_sign_smb vs. the disabled cifs_sign_smb2) for calculating signatures.
This finishes up cifs_sign_smb2/cifs_calc_signature2 so that the callers
of SendReceive2 can get SMB/CIFS packet signatures.
Now that cifs_sign_smb2 is supported, we could start using it in
the write path but this smaller fix does not include the change
to use SMBWrite2 when signatures are required (which when enabled
will make more Writes more efficient and alloc less memory).
Currently Write2 is only used when signatures are not
required at the moment but after more testing we will enable
that as well).
Thanks to James Slepicka and Sam Flory for initial investigation.
Signed-off-by: Steve French <sfrench@us.ibm.com>
Commit 70674f95c0:
[PATCH] Optimize select/poll by putting small data sets on the stack
resulted in the poll stack being 4-byte aligned on 64-bit architectures,
causing misaligned accesses to elements in the array.
This patch fixes it by declaring the stack in terms of 'long' instead
of 'char'.
Force alignment of poll and select stacks to long to avoid unaligned
access on 64 bit architectures.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch documents the Linux kernel's memory barriers.
I've updated it from the comments I've been given.
The per-arch notes sections are gone because it's clear that there are so many
exceptions, that it's not worth having them.
I've added a list of references to other documents.
I've tried to get rid of the concept of memory accesses appearing on the bus;
what matters is apparent behaviour with respect to other observers in the
system.
Interrupts barrier effects are now considered to be non-existent. They may be
there, but you may not rely on them.
I've added a couple of definition sections at the top of the document: one to
specify the minimum execution model that may be assumed, the other to specify
what this document refers to by the term "memory".
I've made greater mention of the use of mmiowb().
I've adjusted the way in which caches are described, and described the fun
that can be had with cache coherence maintenance being unordered and data
dependency not being necessarily implicit.
I've described (smp_)read_barrier_depends().
I've rearranged the order of the sections, so that memory barriers are
discussed in abstract first, and then described the memory barrier facilities
available on Linux, before going on to more real-world discussions and examples.
I've added information about the lack of memory barriering effects with atomic
ops and bitops.
I've added information about control dependencies.
I've added more diagrams to illustrate caching interactions between CPUs.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Wrong error path in dup_fd() - it should return NULL on error,
not an address of already freed memory :/
Triggered by OpenVZ stress test suite.
What is interesting is that it was causing different oopses in RCU like
below:
Call Trace:
[<c013492c>] rcu_do_batch+0x2c/0x80
[<c0134bdd>] rcu_process_callbacks+0x3d/0x70
[<c0126cf3>] tasklet_action+0x73/0xe0
[<c01269aa>] __do_softirq+0x10a/0x130
[<c01058ff>] do_softirq+0x4f/0x60
=======================
[<c0113817>] smp_apic_timer_interrupt+0x77/0x110
[<c0103b54>] apic_timer_interrupt+0x1c/0x24
Code: Bad EIP value.
<0>Kernel panic - not syncing: Fatal exception in interrupt
Signed-Off-By: Pavel Emelianov <xemul@sw.ru>
Signed-Off-By: Dmitry Mishin <dim@openvz.org>
Signed-Off-By: Kirill Korotaev <dev@openvz.org>
Signed-Off-By: Linus Torvalds <torvalds@osdl.org>
Turn some macros into inline functions and add proper type checking as
well as being more readable. Also a minor comment adjustment.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Decrease the number of pointer derefs in drivers/serial/jsm/jsm_tty.c
Benefits of the patch:
- Fewer pointer dereferences should make the code slightly faster.
- Size of generated code is smaller
- Improved readability
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: "V. ANANDA KRISHNAN" <mansarov@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As announced, lookup_hash() can now become static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The only user of get_wchan is the proc fs - and proc can't be built modular.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
And remove the comments that were put in inplace of a fix too....
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently a device failure during recovery leaves bits set in the bitmap.
This normally isn't a problem as the offending device will be rejected because
of errors. However if device re-adding is being used with non-persistent
bitmaps, this can be a problem.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes the old radeon driver which has been replaced by a
newer one.
Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The monochrome->color expansion routine that handles bitmaps which have
(widths % 8) != 0 (slow_imageblit) produces corrupt characters in big-endian.
This is caused by a bogus bit test in slow_imageblit().
Fix.
This patch may deserve to go to the stable tree. The code has already been
well tested in little-endian machines. It's only in big-endian where there is
uncertainty and Herbert confirmed that this is the correct way to go.
It should not introduce regressions.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixes for the pxafb driver:
* Return -EINVAL for resolutions that are too large as per framebuffer
driver policy.
* Increase the error timeout for disabling the LCD controller. The current
timeout is sometimes too short on the Sharp Zaurus Cxx00 hardware and an
extra delay in an error path shouldn't pose any problems.
* Fix a dev reference which causes a compile error when DEBUG is defined.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Generalise the Corgi backlight driver by moving the default intensity and
limit mask settings into the platform specific data structure. This enables
the driver to support other Zaurus hardware, specifically the SL-6000x (Tosa)
model.
Also change the spinlock to a mutex (the spinlock is overkill).
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Updates to the HP Jornada 680 Backlight driver:
- Correct the suspend/resume functions so the driver compiles
(SUSPEND_POWER_DOWN/RESUME_POWER_ON no longer exist).
- Convert the driver to match the recent platform device changes.
- Replace the unsafe static struct platform_device with dynamic allocation.
- Convert the driver to the new backlight code.
This has not been tested on a device due to lack of hardware but wouldn't
compile beforehand.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Backlight class attributes are currently easy to implement incorrectly.
Moving certain handling into the backlight core prevents this whilst at the
same time makes the drivers simpler and consistent. The following changes are
included:
The brightness attribute only sets and reads the brightness variable in the
backlight_properties structure.
The power attribute only sets and reads the power variable in the
backlight_properties structure.
Any framebuffer blanking events change a variable fb_blank in the
backlight_properties structure.
The backlight driver has only two functions to implement. One function is
called when any of the above properties change (to update the backlight
brightness), the second is called to return the current backlight brightness
value. A new attribute "actual_brightness" is added to return this brightness
as determined by the driver having combined all the above factors (and any
driver/device specific factors).
Additionally, the backlight core takes care of checking the maximum brightness
is not exceeded and of turning off the backlight before device removal.
The corgi backlight driver is updated to reflect these changes.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add acceleration support in w100fb.c (i.e. ATI Imageons) for the copyarea and
fillrect operations.
Signed-off-by: Alberto Mardegan <mardy@users.sourceforge.net>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current display was not saved during initialization. This leads to hard
to track console corruption, such as a misplaced cursor, which is correctible
by switching consoles. Fix this minor bug.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is very common to hash a dentry and then to call lookup. If we take fs
specific hash functions into account the full hash logic can get ugly.
Further full_name_hash as an inline function is almost 100 bytes on x86 so
having a non-inline choice in some cases can measurably decrease code size.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Simplifies the code, reduces the need for 4 pid hash tables, and makes the
code more capable.
In the discussions I had with Oleg it was felt that to a large extent the
cleanup itself justified the work. With struct pid being dynamically
allocated meant we could create the hash table entry when the pid was
allocated and free the hash table entry when the pid was freed. Instead of
playing with the hash lists when ever a process would attach or detach to a
process.
For myself the fact that it gave what my previous task_ref patch gave for free
with simpler code was a big win. The problem is that if you hold a reference
to struct task_struct you lock in 10K of low memory. If you do that in a user
controllable way like /proc does, with an unprivileged but hostile user space
application with typical resource limits of 1000 fds and 100 processes I can
trigger the OOM killer by consuming all of low memory with task structs, on a
machine wight 1GB of low memory.
If I instead hold a reference to struct pid which holds a pointer to my
task_struct, I don't suffer from that problem because struct pid is 2 orders
of magnitude smaller. In fact struct pid is small enough that most other
kernel data structures dwarf it, so simply limiting the number of referring
data structures is enough to prevent exhaustion of low memory.
This splits the current struct pid into two structures, struct pid and struct
pid_link, and reduces our number of hash tables from PIDTYPE_MAX to just one.
struct pid_link is the per process linkage into the hash tables and lives in
struct task_struct. struct pid is given an indepedent lifetime, and holds
pointers to each of the pid types.
The independent life of struct pid simplifies attach_pid, and detach_pid,
because we are always manipulating the list of pids and not the hash table.
In addition in giving struct pid an indpendent life it makes the concept much
more powerful.
Kernel data structures can now embed a struct pid * instead of a pid_t and
not suffer from pid wrap around problems or from keeping unnecessarily
large amounts of memory allocated.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
