This patch updates the SuperH gpio code to make use of gpiolib. The
gpiolib callbacks get() and set() are lockless, but we use our own
spinlock for the other operations to make sure hardware register
bitfield accesses stay atomic.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds the SCSPTR register to the sh-sci driver in
the case of sh7723 to make sure early printk builds properly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for "ns16850" as supported value
of the compatible node in flat device tree uart descriptions.
This is needed for example when you have a XR16C2850 uart
connected to a PPC405's external bus controller.
Signed-off-by: Matthias Fuchs <mfuchs@ma-fu.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix the following problem, related to hardware flow control (CTS/RTS):
Transmitting while CTS line is asserted in DMA mode, due to not checking
for tx-stopped condition.
We found these problems while testing the UARTs with hardware
flow-control.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: "Andrew Victor" <avictor.za@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This was not implemented correctly for the pnx8xxx_uart driver.
[From further discussion:
Correct, you can look to it as two separate bugs:
a) the next character is not ignored while it should;
b) the status bits 31-8 are copied to the 'ch' variable while they shouldn't.
Both bugs prevent correct break signal handling (and therefore correct
behaviour of the magic SysRq key). Bug b didn't cause too much trouble
earlier because in most situations the status bits are all zero; for
this case they unfortunately aren't.
]
Signed-off-by: Mischa Jonker <mischa.jonker@nxp.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add SupraExpress 336i PnP Voice Modem
Tested and working with the following device: (output from lspnp -v)
01:01.00 SUP1381 (unknown)
state = active
io 0x2f8-0x2ff
irq 3
Signed-off-by: Daniel Gagnon <daniel.gagnon@yahoo.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most of netmos 9835 hardware is handled by parport-serial. IBM introduces
a device which doesn't have any parallel ports and have screwed subdevice
PCI id (not corresponding to port numbers).
Handle this device (9710:9835 1014:0299) properly.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit b430428a18 ("8250: Don't clobber
spinlocks.") introduced a regression on the parisc architecture, which
broke the handover to the serial port at boottime.
early_serial_setup() was changed to only copy a subset of the uart_port
fields, and sadly the "type" and "line" fields were forgotten and thus
the serial port was not initialized and could not be used for a
handover. This patch fixes this by copying the missing fields.
As this change to early_serial_setup() doesn't need an initialized
spinlock in the uart_port struct any longer, we can drop the spinlock
initialization in the superio driver.
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Julia Lawall found an un-needed check in the neo driver. Her patch moves
the check to cover the code dereferencing it, however it cannot be NULL
anyway so remove the NULL check instead.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Always set CONFIG_SERIAL_SAMSUNG_UARTS when building any
of the S3C platforms as even if the driver is not selected
there it is still the facility for the machine files to
register configuration data for the possibility of the
driver being built.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for the nwp serial device which is connected to a DCR bus. It
uses the of_serial device driver to determine necessary properties from
the device tree. The supported device is added as serial port number 85.
NWP stands for network processor and it is part of the QPACE - Quantum
Chromodynamics Parallel Computing on the Cell Broadband Engine project.
The implementation is a lightweight uart implementation with the focus
to consume as little resources as possible and it is connected to a
DCR bus.
Signed-off-by: Benjamin Krill <ben@codiert.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
Commit d87a6d9 ("drivers/serial/: remove CVS keywords") removed one
space too many in the printk in serial8250_init(). Put it back in (and
add a comma for clarity).
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for Sealevel Systems Model 7803 COMM+8
Signed-off-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cavium UART implementation is not covered by existing uart_configS.
Define a new uart_config (PORT_OCTEON) which is specified by OCTEON
platform device registration code.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add flag value UPF_FIXED_TYPE which specifies that the UART type is
known and should not be probed. For this case the UARTs properties
are just copied out of the uart_config entry.
This allows us to keep SOC specific 8250 probe code out of 8250.c. In
this case we know the serial hardware will not be changing as it is on
the same silicon as the CPU, and we can specify it with certainty in
the board/cpu setup code.
The alternative is to load up 8250.c with a bunch of OCTEON specific
special cases in the probing code.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to use Cavium OCTEON specific serial i/o drivers, we first
patch the 8250 driver to use replaceable I/O functions. Compatible
I/O functions are added for existing iotypeS.
An added benefit of this change is that it makes it easy to factor
some of the existing special cases out to board/SOC specific support
code.
The alternative is to load up 8250.c with a bunch of OCTEON specific
iotype code and bug work-arounds.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In serial8250_isa_init_ports(), the port's lock is initialized. We
should not overwrite it. In early_serial_setup(), only copy in the
fields we need. Since the early console code only uses a subset of
the fields, these are sufficient.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the tty_port and uart_info bits around a little. By embedding the uart_info
into the uart_port we get rid of lots of corner case testing and also get the
ability to go port<->state<->info which is a bit more elegant than the current
data structures.
Downsides - we allocate a tiny bit more memory for unused ports, upside we've
removed as much code as it saved for most users..
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PCI-card identified as "Oxford Semiconductor Ltd EXSYS EX-41092 Dual
16950 Serial adapter" is only usable with other devices (i.e. not the same
card) after doing a "setserial /dev/ttyS<n> baud_base 115200". This
baud_base should be default for this card.
Signed-off-by: Niels de Vos <niels.devos@wincor-nixdorf.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
this happening again by making use of 'const'.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
scribble on its own reference structures.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add spin_lock_irqsave() when receive and transfer data.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bug description:
The IRDA receiver may can't receiving any more after processed some signals.
To duplicate this issue is put three IRDA devices together, one blackfin,
two none blackfin, they will detect each other. Let one none blackfin devices
irdaping the blackfin devices, when it stopped print out ping information,
it is the time that blackfin stoped receiving, the time is random.
The related register bit is OK, the other devices is sending data continuously.
But no interrupt come.
Fixing:
I tried Michael's suggestion that request the UARTx error interrupt, and reset
the IRDA when found FE error. This method helps much, but it can't completely
avoid stop.
Reset the IRDA before every time sending the data is more safe.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (407 commits)
[ARM] pxafb: add support for overlay1 and overlay2 as framebuffer devices
[ARM] pxafb: cleanup of the timing checking code
[ARM] pxafb: cleanup of the color format manipulation code
[ARM] pxafb: add palette format support for LCCR4_PAL_FOR_3
[ARM] pxafb: add support for FBIOPAN_DISPLAY by dma braching
[ARM] pxafb: allow pxafb_set_par() to start from arbitrary yoffset
[ARM] pxafb: allow video memory size to be configurable
[ARM] pxa: add document on the MFP design and how to use it
[ARM] sa1100_wdt: don't assume CLOCK_TICK_RATE to be a constant
[ARM] rtc-sa1100: don't assume CLOCK_TICK_RATE to be a constant
[ARM] pxa/tavorevb: update board support (smartpanel LCD + keypad)
[ARM] pxa: Update eseries defconfig
[ARM] 5352/1: add w90p910-plat config file
[ARM] s3c: S3C options should depend on PLAT_S3C
[ARM] mv78xx0: implement GPIO and GPIO interrupt support
[ARM] Kirkwood: implement GPIO and GPIO interrupt support
[ARM] Orion: share GPIO IRQ handling code
[ARM] Orion: share GPIO handling code
[ARM] s3c: define __io using the typesafe version
[ARM] S3C64XX: Ensure CPU_V6 is selected
...
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (144 commits)
powerpc/44x: Support 16K/64K base page sizes on 44x
powerpc: Force memory size to be a multiple of PAGE_SIZE
powerpc/32: Wire up the trampoline code for kdump
powerpc/32: Add the ability for a classic ppc kernel to be loaded at 32M
powerpc/32: Allow __ioremap on RAM addresses for kdump kernel
powerpc/32: Setup OF properties for kdump
powerpc/32/kdump: Implement crash_setup_regs() using ppc_save_regs()
powerpc: Prepare xmon_save_regs for use with kdump
powerpc: Remove default kexec/crash_kernel ops assignments
powerpc: Make default kexec/crash_kernel ops implicit
powerpc: Setup OF properties for ppc32 kexec
powerpc/pseries: Fix cpu hotplug
powerpc: Fix KVM build on ppc440
powerpc/cell: add QPACE as a separate Cell platform
powerpc/cell: fix build breakage with CONFIG_SPUFS disabled
powerpc/mpc5200: fix error paths in PSC UART probe function
powerpc/mpc5200: add rts/cts handling in PSC UART driver
powerpc/mpc5200: Make PSC UART driver update serial errors counters
powerpc/mpc5200: Remove obsolete code from mpc5200 MDIO driver
powerpc/mpc5200: Add MDMA/UDMA support to MPC5200 ATA driver
...
Fix trivial conflict in drivers/char/Makefile as per Paul's directions
sci_poll_put_char() happens to also be used by the serial console,
while sci_poll_get_char() is only used by CONFIG_CONSOLE_POLL. Add
another gnarly ifdef to shut up the compiler.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the SH-2A FPU based SH7201 processor subtype.
Signed-off-by: Peter Griffin <pgriffin@mpc-data.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
- error cases for mapbase and irq were unbundled
- mapped irq now gets disposed on error
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add RTS/CTS-support for the PSC of the MPC5200B. Tested with a Phytec
MPC5200B-IO.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds the capability to the mpc52xx-uart to report framing
errors, parity errors, breaks and overruns to userspace. These values
may be requested in userspace by using the ioctl TIOCGICOUNT.
Signed-off-by: René Bürgel <r.buergel@unicontrol.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
As noted by Russell King, do not print any warnings if the
uinfo or tty fields are not set when a CPU frequency change
is sent.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the usage of CONFIG_SERIAL_SAMSUNG_UARTS in several places
in the kernel where it had been missed. This finishes fixing a
long standing issue where S3C2443 and S3C64XX could not use the
4th UART
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch removes the inclusion of mach/hardware.h from mach/irqs.h and
switches to more meaningful names for the irq related macros.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adds support for MX1 architecture to UART driver.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The S3C64XX code changes the order of the serial
interrupts, so change the registration process to
pickup the extra IRQ resources.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add serial support for S3C24A0, based on current S3C2410
UART driver. It adds necessary new defines in regs-serial.h
for S3C24A0 and the code to support this device in
drivers/serial/s3c24a0.c
Signed-off-by: Sandeep Patil <sandeep.patil@azingo.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] SN: prevent IRQ retargetting in request_irq()
[IA64] Fix section mismatch ioc3uart_init()/ioc3uart_submodule
[IA64] Clear up section mismatch for ioc4_ide_attach_one.
[IA64] Clear up section mismatch with arch_unregister_cpu()
[IA64] Clear up section mismatch for sn_check_wars.
[IA64] Updated the generic_defconfig to work with the 2.6.28-rc7 kernel.
[IA64] Fix GRU compile error w/o CONFIG_HUGETLB_PAGE
[IA64] eliminate NULL test and memset after alloc_bootmem
[IA64] remove BUILD_BUG_ON from paravirt_getreg()
[Folded together as one diff from 3]
It should be 'lose', not 'loose'.
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Where devices only have one consumer, passing a consumer clock ID
has no real benefit, and it only encourages wrong implementations of
the clk API. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Avoid unnecessarily pollution of the kernel's namespace by avoiding
mach/hardware.h in mach/io.h. Include this header file where necessary.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Where devices only have one consumer, passing a consumer clock ID
has no real benefit. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This implements poll_get_char and poll_put_char for console polling,
which enables kgdb to work on machines that use the pmac_zilog serial
driver, for example the Apple PowerMac G5.
Signed-off-by: Chris J Arges <arges@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Various printk format string in code used by the Xilinx Virtex platform
are not 32-bit/64-bit safe. Add correct casting to fix the bugs.
Reported-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Under qemu there is a race between the TDxE read-and-clear and the SCxTDR
write. While on hardware it can be gauranteed that the read-and-clear
will happen prior to the character being written out, no such assumption
can be made under emulation. As this path happens with IRQs off and the
hardware itself doesn't care about the ordering, move the SCxTDR write
until after the read-and-clear.
Signed-off-by: Vladimir Prus <vladimir@codesourcery.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH7723 has SCIFA. This module is similer SCI register map, but it has FIFO.
So this patch adds new type(PORT_SCIFA) and change some type checking.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The atmel_serial driver is mismanaging its clock by leaving it on at all
times ... the whole point of clock management is to leave it off unless
it's actively needed, which conserves power!!
Although the kernel doesn't actually hang without my fix, it does
discard quite a lot of early console output.
The result still looks correct:
usart users= 1 on 35000000 Hz, for atmel_usart.0
usart users= 0 off 35000000 Hz, for atmel_usart.2
when using ttyS0 as serial console.
[haavard.skinnemoen@atmel.com: Make sure clock is enabled early for console]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Correct the interrupt handler in sh4 serial device, return the correct
value and check for what is anabled in the SCSCR register. The sh7722 is
broken just sending a break using minicom.
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
After the recent commit to kill off SCI/SCIF special casing SH 7751R
fails to compile with CONFIG_SH_RTS7751R2D set. This is because SCSPTR1
is undefined. Take the value for SCSPTR1 from the SH7751R Group Hardware
Manual.
Signed-off-by: Matt Fleming <mjf@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH4-202 doesn't have SCSXX1. But it is treated so that there is SCSPTR1 in
current code. This patch add sci_rxd_in of SH4-202.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This change a name of SCSPTR used in sci_rxd_in of SH5-101.
SCSPTR is not declared and will become the error.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Make the netX serial driver tristate (as the help text implied). Make the
serial driver build correctly if the netX serial console is disabled. Do not
allow the netX serial console if the netX serial driver is build as a module.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This reverts commit 5ca8c4852f.
With the killing off of SCIF_ONLY and its spawn in sh-sci, we no longer
require this change, so just revert it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH 7366 has compile bug.
because there is no SCIF_ONLY for SH 7366.
this patch add it.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These have the Mainpine PCI identifier on however
Additional paranoia check for Tornado versions added by Alan Cox
(and this time I remembered to do an stg refresh so that the corrections ended
up in these patches not randomly attached to another diff -- Alan)
Signed-off-by: Lee Howard <lee.howard@mainpine.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the OxSemi 'Tornado' devices.
Reformatted and reworked a bit by Alan Cox
Signed-off-by: Lee Howard <lee.howard@mainpine.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This merges branches irq/genirq, irq/sparseirq-v4, timers/hpet-percpu
and x86/uv.
The sparseirq branch is just preliminary groundwork: no sparse IRQs are
actually implemented by this tree anymore - just the new APIs are added
while keeping the old way intact as well (the new APIs map 1:1 to
irq_desc[]). The 'real' sparse IRQ support will then be a relatively
small patch ontop of this - with a v2.6.29 merge target.
* 'genirq-v28-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (178 commits)
genirq: improve include files
intr_remapping: fix typo
io_apic: make irq_mis_count available on 64-bit too
genirq: fix name space collisions of nr_irqs in arch/*
genirq: fix name space collision of nr_irqs in autoprobe.c
genirq: use iterators for irq_desc loops
proc: fixup irq iterator
genirq: add reverse iterator for irq_desc
x86: move ack_bad_irq() to irq.c
x86: unify show_interrupts() and proc helpers
x86: cleanup show_interrupts
genirq: cleanup the sparseirq modifications
genirq: remove artifacts from sparseirq removal
genirq: revert dynarray
genirq: remove irq_to_desc_alloc
genirq: remove sparse irq code
genirq: use inline function for irq_to_desc
genirq: consolidate nr_irqs and for_each_irq_desc()
x86: remove sparse irq from Kconfig
genirq: define nr_irqs for architectures with GENERIC_HARDIRQS=n
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (112 commits)
sh: Move SH-4 CPU headers down one more level.
sh: Only build in gpio.o when CONFIG_GENERIC_GPIO is selected.
sh: Migrate common board headers to mach-common/.
sh: Move the CPU definition headers from asm/ to cpu/.
serial: sh-sci: Add support SCIF of SH7723
video: add sh_mobile_lcdc platform flags
video: remove unused sh_mobile_lcdc platform data
sh: remove consistent alloc cruft
sh: add dynamic crash base address support
sh: reduce Migo-R smc91x overruns
sh: Fix up some merge damage.
Fix debugfs_create_file's error checking method for arch/sh/mm/
Fix debugfs_create_dir's error checking method for arch/sh/kernel/
sh: ap325rxa: Add support RTC RX-8564LC in AP325RXA board
sh: Use sh7720 GPIO on magicpanelr2 board
sh: Add sh7720 pinmux code
sh: Use sh7203 GPIO on rsk7203 board
sh: Add sh7203 pinmux code
sh: Use sh7723 GPIO on AP325RXA board
sh: Add sh7723 pinmux code
...
In function sn_sal_switch_to_asynch(): drivers/serial/sn_console.c:713:
HZ * SN_SAL_UART_FIFO_DEPTH / SN_SAL_UART_FIFO_SPEED_CPS;
After preprocessing (see defines in patch) this becomes HZ * 16 / 9600 / 10
(associativity from left to right), not equivalent to HZ * 16 / 960.
Looks-obviously-right-to: Tony Luck <tony.luck@intel.com>
Cc: Jes Sorensen <jes@sgi.com>
Acked-by: Pat Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes the needlessly global probe_serial_gsc() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SH7723 has two types of SCIF (SCIF and SCIFA).
The current sh-sci driver supports only SCIFA, and calculation methods of SCBRR
are different.
This patch support this methods.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SERIAL_SAMSUNG_DEBUG used printascii() to avoid debugging
through itself when selected as a console. Disable this option
when DEBUG_LL is not set (printascii is unavailable).
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Splitting the 8250 code back up to avoid a clash with the NR_IRQS removal
patch introduced a last minute bug. Put back the additional needed lines
for the old lock init
Signed-off-by: Alan Cox <alan@redhat.com>
[ Ingo also reports that this can cause a spontaneous reboot crash with
certain configs, and sends in an identical patch ]
Tested-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The multiple drivers share the minor space occupied by a particular major
number, the actual index within the device name's space is indicated by
the tty_driver->name_base + uart_port->line
Another usable formula is (uart_driver->minor - MINOR_BASE) + port->line
Use those to print the device names properly in such situations in
serial_core.c and 8250.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Copy the simplification from the pty unix98 special case to the generic one.
This allows us to kill off driver->termios_locked entirely which is nice. We
have to whack bits of the cris driver as it meddles in places it shouldn't
providing its own arrays that were never used anyway.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This requires three changes:
1) Remove !SPARC restriction in Kconfig.
2) Move Sparc specific serial drivers before 8250, so that serial
console devices don't change names on us, even if 8250 finds
devices.
3) Since the Sparc specific serial drivers try to use the
same major/minor device namespace as 8250, some coordination
is necessary. Use the sunserial_*() layer routines to allocate
minor number space within TTY_MAJOR when CONFIG_SPARC.
This has no effect on other platforms.
Thanks to Josip Rodin for bringing up this issue and testing
plus debugging various revisions of this patch.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove some inlines from various functions that are called once, are too
big to inline, or are called only from slow path code. This saves around
300 bytes of code for me.
Signed-off-by: Will Newton <will.newton@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
<rmk> talking about leaks - I noticed that the 'check return of
pci_enable_dev()' in the 8250 pci resume function finally made it in
despite my objections against it (causing stuff in higher levels to
leak).
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We now use the sir_dev/irtty_sir/uart/bfin_serial drivers framework
to monitor the TX status.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
move common variables out of serial headers and into the serial driver and
rename "nr_ports" to "nr_active_ports" so as to easily differentiate
between BFIN_UART_NR_PORTS (the # of available) and nr_ports (the # of enabled)
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch contains the scheduled removal of the obsolete
SERIAL_COLDFIRE driver.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alloc_tty_driver is called at the beginning of the function containing the
lines of code shown in the patch. Thus, put_tty_driver is needed before
returning in the error handling code.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@nr exists@
local idexpression x;
expression E,f;
position p1,p2,p3;
identifier l;
statement S;
@@
x = alloc_tty_driver@p1(...)
...
if (x == NULL) S
... when != E = x
when != put_tty_driver(x)
when != goto l;
(
return \(0\|x\);
|
return@p3 ...;
)
@script:python@
p1 << nr.p1;
p3 << nr.p3;
@@
print "%s: call on line %s not freed or saved before return on line %s" % (p1[0].file,p1[0].line,p3[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (236 commits)
[ARM] 5300/1: fixup spitz reset during boot
[ARM] 5295/1: make ZONE_DMA optional
[ARM] 5239/1: Palm Zire 72 power management support
[ARM] 5298/1: Drop desc_handle_irq()
[ARM] 5297/1: [KS8695] Fix two compile-time warnings
[ARM] 5296/1: [KS8695] Replace macro's with trailing underscores.
[ARM] pxa: allow multi-machine PCMCIA builds
[ARM] pxa: add preliminary CPUFREQ support for PXA3xx
[ARM] pxa: add missing ACCR bit definitions to pxa3xx-regs.h
[ARM] pxa: rename cpu-pxa.c to cpufreq-pxa2xx.c
[ARM] pxa/zylonite: add support for USB OHCI
[ARM] ohci-pxa27x: use ioremap() and offset for register access
[ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()
[ARM] ohci-pxa27x: use platform_get_{irq,resource} for the resource
[ARM] ohci-pxa27x: move OHCI controller specific registers into the driver
[ARM] ohci-pxa27x: introduce flags to avoid direct access to OHCI registers
[ARM] pxa: move I2S register and bit definitions into pxa2xx-i2s.c
[ARM] pxa: simplify DMA register definitions
[ARM] pxa: make additional DCSR bits valid for PXA3xx
[ARM] pxa: move i2c register and bit definitions into i2c-pxa.c
...
Fixed up conflicts in
arch/arm/mach-versatile/core.c
sound/soc/pxa/pxa2xx-ac97.c
sound/soc/pxa/pxa2xx-i2s.c
manually.
First move of items out of include/asm-arm/plat-s3c* to their
new homes under arch/arm/plat-s3c/include/plat and
arch/arm/plat-s3c24xx/include/plat directories.
Note, we have to create a dummy arch/arm/plat-s3c/Makefile to
allow us to add arch/arm/plat-s3c/include/plat to the path.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This was added at a time when the compiler did a less than stellar job of
optimizing out dead code. These days this tends to be less of a concern,
so kill it all off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently this is conditionalized on sh, and disabled for sh64.
Now that SH-5 ties in to the clock framework, the sh64 exception
can be dropped. Additionally, ARM will want to use the same hooks
once SH-Mobile G3 grows clock framework support, so switch these
paths over to HAVE_CLK now.
Once the H8 and ARM sh-sci users hook up HAVE_CLK, the driver can
be switched over to having an outright dependency on it and the
ifdefs can go away.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The function ks8695uart_set_termios() would cause an unbalanced
enable_irq() generated message to be printk()ed. This is because
there was no book keeping support to remember if the calls to
enable_irq() and disable_irq() were balanced for the modem
control irq.
Signed-off-by: Dick Hollenbeck <dick@softplc.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Presently we don't do much with UPF_IOREMAP other than special case it
for SH-5's onchip_remap() on the early console. Tie this in generically
for platforms that need the remap.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that arch/ppc is gone we don't need CONFIG_PPC_MERGE anymore
remove the dead code associated with !CONFIG_PPC_MERGE.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This problem seems to be unnoticed so far:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=b3b708fa2780cd2b5d8266a8f0c3a1cab364d4d2
has changed the serial core behavior to not to suspend the port if the
device is enabled as a wakeup source. If the AT91 system goes to slow
clock mode, the port should be suspended always and the clocks should be
switched off. The patch attached updates the atmel_serial driver to match
the changes in serial core.
Also, the interrupts are disabled when the clock is disabled. If we
disable the clock with interrupts enabled, an interrupt may get stuck. If
this is the DBGU interrupt, this blocks the OR logic at system controller
and thus all other sysc interrupts.
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Michael Trimarchi <trimarchimichael@yahoo.it>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We're currently passing NULL, and really shouldn't be.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Acked-By: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With the change to device tree based setup we no longer need the explicit
Kconfig options for each SCC{1,4} or SMC{1,2} port.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Adds hardware CTSRTS control for pxa serial devices through
termios controls.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A function to contain common code for the size of the resource we
need to allocate or free. OMAP ports need 22 bytes rather than
the standard 8 bytes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make is_omap_port() take the uart_8250_port structure so it can do
whatever test it desires. Convert the test to compare the physical
addresses rather than virtual addresses.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Recent changes to tighten the check for UARTs that don't correctly
re-assert THRE (01c194d927: "serial 8250:
tighten test for using backup timer") caused problems when such a UART was
opened for the second time - the bug could only successfully be detected
at first initialization. For users of this version of this particular
UART IP it is fatal.
This patch stores the information about the bug in the bugs field of the
port structure when the port is first started up so subsequent opens can
check this bit even if the test for the bug fails.
David Brownell: "My own exposure to this is that the UART on DaVinci
hardware, which TI allegedly derived from its original 16550 logic, has
periodically gone from working to unusable with the mainline 8250.c ...
and back and forth a bunch. Currently it's "unusable", a regression from
some previous versions. With this patch from Will, it's usable."
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Alex Williamson <alex.williamson@hp.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Cc: <stable@kernel.org> [2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
