This patch also resolves hangs on boot:
http://lkml.org/lkml/2008/2/23/263http://bugzilla.kernel.org/show_bug.cgi?id=10093
The bug was causing once-in-few-reboots 10-15 sec wait during boot on
certain laptops.
Earlier commit 40d6a14662 added
smp_call_function in cpu_idle_wait() to kick cpus that are in tickless
idle. Looking at cpu_idle_wait code at that time, code seemed to be
over-engineered for a case which is rarely used (while changing idle
handler).
Below is a simplified version of cpu_idle_wait, which just makes a dummy
smp_call_function to all cpus, to make them come out of old idle handler
and start using the new idle handler. It eliminates code in the idle
loop to handle cpu_idle_wait.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shift of a LE value seems strange, probably meant to shift the cpu-order
variable as in the prvious section of the switch statement.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't make smp_{r,w,}mb() interpolate a MEMBAR instruction when CONFIG_SMP=n as
SMP memory barries on UP systems should interpolate a compiler barrier only.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make NOMMU-mode work with base addresses other than 0xC0000000 by:
(1) Giving the code that sets up the protection registers the right address
in __sdram_base. Rather than being hard coded to 0xC0000000, the value
of __page_offset is obtained from the linker script.
(2) Eliminate the check in __switch_to() that verifies the current thread
info is in the 0xCxxxxxxx region.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use traps 120-126 to emulate atomic cmpxchg32, xchg32, and XOR-, OR-, AND-, SUB-
and ADD-to-memory operations for userspace.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move STACK_TOP_MAX up so that we don't try moving the stack above it as that
causes setup_arg_pages() to malfunction.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Handle update_mmu_cache() being called when current->mm is NULL.
We cache static TLB mappings for the current page table in DAMPR4 and DAMPR5
on the theory that the next data lookup is likely to be in the same general
region, and thus is likely to be mapped by the same page table. However, we
can't get this information if we can't access the appropriate mm_struct.
If current->mm is NULL, we just clear the cache in the knowledge that the TLB
miss handlers will load it.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6:
[XFS] Ensure "both" features2 slots are consistent
[XFS] Fix superblock features2 field alignment problem
[XFS] remove shouting-indirection macros from xfs_sb.h
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cfq-iosched: do not leak ioc_data across iosched switches
splice: fix infinite loop in generic_file_splice_read()
Some time ago while attempting to handle invalid link counts, I botched
the unlink of links itself, so this patch fixes this now correctly, so
that only the link count of nodes that don't point to links is ignored.
Thanks to Vlado Plaga <rechner@vlado-do.de> to notify me of this
problem.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When switching scheduler from cfq, cfq_exit_queue() does not clear
ioc->ioc_data, leaving a dangling pointer that can deceive the following
lookups when the iosched is switched back to cfq. The pattern that can
trigger that is the following:
- elevator switch from cfq to something else;
- module unloading, with elv_unregister() that calls cfq_free_io_context()
on ioc freeing the cic (via the .trim op);
- module gets reloaded and the elevator switches back to cfq;
- reallocation of a cic at the same address as before (with a valid key).
To fix it just assign NULL to ioc_data in __cfq_exit_single_io_context(),
that is called from the regular exit path and from the elevator switching
code. The only path that frees a cic and is not covered is the error handling
one, but cic's freed in this way are never cached in ioc_data.
Signed-off-by: Fabio Checconi <fabio@gandalf.sssup.it>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Since older kernels may look in the sb_bad_features2 slot for flags,
rather than zeroing it out on fixup, we should make it equal to the
sb_features2 value.
Also, if the ATTR2 flag was not found prior to features2 fixup, it was not
set in the mount flags, so re-check after the fixup so that the current
session will use the feature.
Also fix up the comments to reflect these changes.
SGI-PV: 980085
SGI-Modid: xfs-linux-melb:xfs-kern:30778a
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Due to the xfs_dsb_t structure not being 64 bit aligned, the last field of
the on-disk superblock can vary in location This causes problems when the
filesystem gets moved to a different platform, or there is a 32 bit
userspace and 64 bit kernel.
This patch detects the defect at mount time, logs a warning such as:
XFS: correcting sb_features alignment problem
in dmesg and corrects the problem so that everything is OK. it also
blacklists the bad field in the superblock so it does not get used for
something else later on.
SGI-PV: 977636
SGI-Modid: xfs-linux-melb:xfs-kern:30539a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Remove macro-to-small-function indirection from xfs_sb.h, and remove some
which are completely unused.
SGI-PV: 976035
SGI-Modid: xfs-linux-melb:xfs-kern:30528a
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Donald Douwsma <donaldd@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
There's a quirky loop in generic_file_splice_read() that could go
on indefinitely, if the file splice returns 0 permanently (and not
just as a temporary condition). Get rid of the loop and pass
back -EAGAIN correctly from __generic_file_splice_read(), so we
handle that condition properly as well.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
gcc expects all toplevel assembly to return to the original section type.
The code in alteranative.c does not do this. This caused some strange bugs
in sched-devel where code would end up in the .rodata section and when
the kernel sets the NX bit on all .rodata, the kernel would crash when
executing this code.
This patch adds a .previous marker to return the code back to the
original section.
Credit goes to Andrew Pinski for telling me it wasn't a gcc bug but a
bug in the toplevel asm code in the kernel. ;-)
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I (wrongly) assumed that nfs_xdev_get_sb() would not ever share a superblock
and so cloning mount options would always be correct. Turns out that isn't
the case and we could fall over a BUG_ON() that wasn't a BUG at all. Since
there is little we can do to reconcile different mount options this patch
just leaves the sb alone and the first set of options wins.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: James Morris <jmorris@namei.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata/sata_fsl: Remove unused variable in sata_fsl_probe
pata_sil680: Fix build on arch/ppc
In sata_fsl_probe memory is allocated but never used or deallocated.
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=10404
Thanks to Daniel Marjamäki for the bug report.
Reported-by: Daniel Marjamäki <danielm77@spray.se>
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Commit 0f436eff54 breaks build on
arch/ppc as it doesn't implement the machine_is() macro.
This fixes it by using CONFIG_PPC_MERGE instead which represents
arch/powerpc only, while CONFIG_PPC is set for both.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'hotfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
SUNRPC: Fix a memory leak in rpc_create()
fix bug - executing FDPIC ELF on NFS mount triggers BUG() at mm/nommu.c:862:/do_mmap_private()
NFS: initialize flags field in nfs_open_context
SUNRPC: don't call flush_dcache_page() with an invalid pointer
cfi_amdstd_sync() and cfi_staa_sync() call schedule() without changing task's
state appropriately.
In case of e.g. chip->state == FL_ERASING, cfi_*_sync() will be busy-looping
either redundantly for a fixed interval of time (for SCHED_NORMAL tasks) or
possibly endlessly (for RT tasks and UP).
Signed-off-by: Dmitry Adamushko <dmitry.adamushko@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update SPI documentation to clarify some areas of recent confusion: clock
polarity takes effect when chipselect goes active; and zero length buffers are
OK in certain cases.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix bug in SPI probe: first initialize peripheral pins, and just after
register spi master device. This fixes problems with SPI drivers built-in
kernel.
Singed-off-by: Vitja Makarov <vitja.makarov@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix breakage cause by overzealous line wrapping; there should be only one
format string.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes a BUG in ACPI hotplugging.
processor_device_array[pr->id] needs to be set to NULL when removing a CPU.
Else the "buggy BIOS check" in acpi_processor_start mistakenly fires when a
CPU is removed from the system and then later re-added.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Dan Arai <arai@vmware.com>
Cc: Len Brown <lenb@kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
snd_es1968_ac97_read() calls snd_es1968_ac97_wait() first outside a locked
area, and later, while holding a lock.
snd_es1968_ac97_wait() has a polling loop with a cond_resched() inside it..
which sleeps, so the second call is invalid.
This patch adds a version of the wait function that just pure polls. While
this is not very elegant in principle, it's very likely the easiest thing to
do here, we already checked if the chip was ready (while yielding) just
before, so it is very unlikely to take a long time here.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This should be N_NORMAL_MEMORY.
N_NORMAL_MEMORY is "true" if a node has memory for the kernel. N_HIGH_MEMORY
is "true" if a node has memory for HIGHMEM. (If CONFIG_HIGHMEM=n, always
"true")
This check is used for testing whether we can use kmalloc_node() on a node.
Then, if there is a node which only contains HIGHMEM, the system will call
kmalloc_node() which doesn't contain memory for the kernel. If it happens
under SLUB, the kernel will panic. I think this only happens on x86_32-numa.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
thermal_zone_device_register() uses the ERR_PTR macro on its return values. A
correct check is to use the IS_ERR() macro.
The 2.6.25 kernels panic on Compaq AP550 without this patch as it has more
then 10 (THERMAL_MAX_TRIPS) trip points (there are 12).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When __blk_end_request returns nonzero, it means that the request was
not completely processed and some BIOs are still attached. Since we
have dequeued it by that time, it means leaking requests and hanging
processes, which is why BUG() was in there. In ub this happens if
a packet request ends normally, but with residue (e.g. when scsi_id
issues INQUIRY).
The fix is to make sure that arguments passed to __blk_end_request
are correct: the full request length and not just transferred length.
The transferred length is indicated to applications by adjusting
rq->data_len with old, unchanged code outside of this patch.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Cc: Greg KH <greg@kroah.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 510deb0d was supposed to move the xprt_create_transport() call in
rpc_create(), but neglected to remove the old call site. This resulted in
a transport leak after every rpc_create() call.
This leak is present in 2.6.24 and 2.6.25.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The nfs_open_context struct had a "flags" field added recently, but the
allocator isn't initializing it. It also looks like the allocator isn't
initializing the mode or list either, but they seem to be overwritten
by the caller, so that's less of an issue.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Fix a problem in _copy_to_pages(), whereby it may call flush_dcache_page()
with an invalid pointer due to the fact that 'pgto' gets incremented
beyond the end of the page array. Fix is to exit the loop without this
unnecessary increment of pgto.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
SELinux: more GFP_NOFS fixups to prevent selinux from re-entering the fs code
Fix broken build due to patch order dependency. A future patch requires
the lines that break the current build. Disable those lines for now.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
More cases where SELinux must not re-enter the fs code. Called from the
d_instantiate security hook.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
flush_cache_vmap / flush_cache_vunmap were calling flush_cache_all which -
having been deprecated - turned into a nop ...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix kernel oops due to machine check occuring in init_chipset_siimage() on PPC
44x platforms. These 32-bit CPUs have 36-bit physical address and PCI I/O and
memory spaces are mapped beyond 4 GB; arch/ppc/ code has a fixup in ioremap()
that creates an illusion of the PCI I/O and memory resources being mapped below
4 GB, while arch/powerpc/ code got rid of this fixup with PPC 44x having instead
CONFIG_RESOURCES_64BIT=y -- this causes the resources to be truncated to 32-bit
'unsigned long' type in this driver, and so non-existant memory being ioremap'ed
and then accessed...
Thanks to Valentine Barshak for providing an initial patch and explanations.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The 'disable_cb' is really just a hint and as such, it's possible for more
work to get queued up while callbacks are disabled. Under stress with an
SMP guest, this printk triggers very frequently. There is no race here, this
is how things are designed to work so let's just remove the printk.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 9e6db60825, which was
merged without the API it needed, causing build breakage.
Reported-by: Bryan Wu <cooloney@kernel.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
x86: fix 64-bit asm NOPS for CONFIG_GENERIC_CPU
x86: fix call to set_cyc2ns_scale() from time_cpufreq_notifier()
revert "x86: tsc prevent time going backwards"
The 'disable_cb' callback is designed as an optimization to tell the host
we don't need callbacks now. As it is not reliable, the debug check is
overzealous: it can happen on two CPUs at the same time. Document this.
Even if it were reliable, the virtio_net driver doesn't disable
callbacks on transmit so the START_USE/END_USE debugging reentrance
protection can be easily tripped even on UP.
Thanks to Balaji Rao for the bug report and testing.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
CC: Balaji Rao <balajirrao@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In time_cpufreq_notifier() the cpu id to act upon is held in freq->cpu. Use it
instead of smp_processor_id() in the call to set_cyc2ns_scale().
This makes the preempt_*able() unnecessary and lets set_cyc2ns_scale() update
the intended cpu's cyc2ns.
Related mail/thread: http://lkml.org/lkml/2007/12/7/130
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
revert:
| commit 47001d6033
| Author: Thomas Gleixner <tglx@linutronix.de>
| Date: Tue Apr 1 19:45:18 2008 +0200
|
| x86: tsc prevent time going backwards
it has been identified to cause suspend regression - and the
commit fixes a longstanding bug that existed before 2.6.25 was
opened - so it can wait some more until the effects are better
understood.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
