On FSC laptops, the sound gets muted gradually when the volume is chnaged.
This is due to the wrong volume-knob widget setup. The delta bit (bit 7)
shouldn't be set for these devices.
This patch adds a new quirk to set the value 0x7f to the widget 0x24
instead of 0xff.
Reference: Novell bnc#546006
http://bugzilla.novell.com/show_bug.cgi?id=546006
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC861-VD lenovo model causes overflow of spec->init_verbs entries due to
the recent changes. Simply increase the array size to avoid the overflow.
Reported-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow Nvidia HDMI to support more possible sample rates and formats.
At best, the really supported rates and formats should be determined
together with the negotiation with the HDMI receiver, but it's currently
not implemented yet (Nvidia stuff seems incompatible with HDMI 1.3
standard in this regard). As a compromise, we enable all bits, assuming
that all recent devices do support such rates/formats.
Tested-by: Alan Alan <alanwww1@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since patch_alc268() doesn't call set_capture_mixer() (due to its h/w
design different from other siblings), it needs to call fixup_automic_adc()
explicitly to set up the auto-mic routing. Otherwise the indices for
int/ext mics aren't set properly.
Reference: Novell bnc#544899
http://bugzilla.novell.com/show_bug.cgi?id=544899
Signed-off-by: Takashi Iwai <tiwai@suse.de>
alc_subsystem_id() tries to pick up a headphone pin if not configured,
but this caused side-effects as the problem in commit
15870f05e9.
This patch fixes the driver behavior to pick up invalid HP pins; at least,
the pins that are listed as the primary outputs aren't taken any more.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS A7K needs additional GPIO1 bit setup; it has to be cleared.
Added a new fixup hook for this laptop so that it works as is.
Refernece: Novell bnc#494309
http://bugzilla.novell.com/show_bug.cgi?id=494309
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent auto-parser doesn't work for machines with a single output
with ALC861, such as Toshiba laptops, because alc_subsystem_id() sets
the hp_pins[0] while it's listed in line_outs[0].
This ends up with the doubled initialization of the same mixer widget,
and it mutes the DAC route because hp_pins has no DAC assigned.
To fix this problem, just check spec->autocfg.hp_outs and speaker_outs
so that they are really detected pins.
Reference: Novell bnc#544161
http://bugzilla.novell.com/show_bug.cgi?id=544161
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The auto-parser for ALC662/663/272 codecs doesn't work properly when
a speaker is connected to mono NID 0x17, and doesn't handle the dynamic
DAC assignment properly.
This patch fixes the issues and also improves the assignment of DACs
so that HP and speakers can have independent volume controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the auto-mic switching between an analog and a digital mic is
needed with IDT codecs, the current driver doesn't reset the connection
of the digital mux.
This patch fixes the behavior by checking both mux connections properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Patch was tested on Toshiba NB200 and is found to enable sound.
Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the commit fdbc66266c, I mistakenly
replaced the capture mixer array for ALC268_ACER to nosrc version
although this should be kept to alt_mixer. Now fixed back.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reference: ALSA bug #0004614https://bugtrack.alsa-project.org/alsa-bug/view.php?id=4614
port-A (0x11) - front hp-out
port-D (0x12) - rear line out
port-E (0x1c) - front mic-in
port-F (0x16) - Internal speakers
digital-mic (0x17) - Internal mic
init verbs, mixers, jack sensing and PCI_QUIRK to support this hardware
Signed-off-by: Miguel de Barros <miguel.de.barros@bluewin.ch>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After puting a cd-audio inside my laptop there was no sound out here,
so I decided to install alsa-driver with debug level and setup a
model=test, it didn't help, but then I look at source code and added
this few lines, now cd-audio is working both when playback/recording.
[Additional minor fixes of mixer element/item names by tiwai]
Signed-off-by: Lukasz Marcinowski <nowymarluk@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The headphone and speaker mixer elements aren't properly set for
MSI GX620 with targa-8ch-dig quirk.
Also fixed the speaker volume control for other ALC883-targa quirks,
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The pin setup for Dell S14 quirk is rather wrong for the latest driver.
Fixed pin 0x0a, 0x0b, 0x0d and 0x0f.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove unnecessary (and buggy) init sequences left for IDT92HD83*
codecs in the previous fixes. The DACs are now dynamically connected,
thus shouldn't be set statically in init verbs. Also, the mono_nid
is detected dynamically, thus shouldn't be set staticaly, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the quirk entry for HP dv6. Also add a workaround for the headphone
detection by setting hp_detect=1 beforehand. Without this, the driver
won't do auto-muting because BIOS doesn't give any HP pin but only a
line-out pin.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's possible that hp_detect is set even though no headphone pin is
detected. The driver issues, however, an unsol event only to hp_pins[0],
which can be invalid.
This patch adds the check of the valid pin to send an unsol event
at initialization and resume callbacks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
IDT92HD73xx and STAC927x codecs use GPIO0 bit as EAPD on many machines.
However, currently we don't set it unless the model is specified just
for safety reason. But, most machines do need this bit, so this safety
handling is rather annoying.
This patch enables GPIO0 setup as default for them. Many HP / Dell
laptops should work even without model override with this change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP laptops with ALC268 codec seem working better with model=auto
than model=toshiba; e.g. the auto model fixes missing digital outputs.
Let's fix quirk entry to choose auto model explicitly.
Tested-by: Jens Jorgensen <jbj1@ultraemail.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The model clevo-m540r was created with 6-channel and digital support. All
functions verified except spdif. Tested with a VIT D2000 laptop which has:
[lspci extract]
Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD Audio
Controller [8086:284b] (rev 03)
Subsystem: CLEVO/KAPOK Computer Device [1558:5409]
[/proc/asound/card0/codec\#0 header]
Codec: Realtek ALC883
Address: 0
Function Id: 0x1
Vendor Id: 0x10ec0883
Subsystem Id: 0x15585409
Revision Id: 0x100002
[Added a comment about HP mute and the model description by tiwai]
Signed-off-by: Dhionel Diaz <ddiaz@cenditel.gob.ve>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the quirk for Alienware M17x with IDT 92HD73* codec chip.
It has two HP and one line-out jack, one mic jack, a built-in
speaker and a built-in mic.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Due to the previous fix of input source for IDT92HD73xx, the amp mux
and amp vol stuff became unused. Let's rip off dead codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the mux_nids to select directly the input source instead of mux
mixers so that it works with the current mux enum handler for IDT
92HD73xx codecs.
Also, clean up useless / unnecessary mixer controls and init verbs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Unmute the docking-station line-out as default on machines with
AD1984A codec chip. It can be still muted via "Dock" mixer switch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the support of automatic mute and mic-switching of the docking
station HP and mic plugs for AD1984A laptop model for some HP machines.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the headphone pin routing of ALC268/ALC269 codecs. Using alc882
routine doesn't work because alc268/alc269 parser assumes the
independent DACs for both HP and speaker outputs. Need to assign the
DAC depending on the pin.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes the wrong headphone output routing for MacBookPro 3,1/4,1
quirk with ALC889A codec, which caused the silent headphone output.
Also, this gives the individual Headphone and Speaker volume controls.
Reference: kernel bug#14078
http://bugzilla.kernel.org/show_bug.cgi?id=14078
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
In patch_vt1708(), the check of MUX nids is missing and this results in
the -EINVAL error in accessing Input Source mixer element. Simpliy
adding the call of get_mux_nids() fixes the problem.
Reference: Novell bnc#534904
https://bugzilla.novell.com/show_bug.cgi?id=534904
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, the digital mic capture volume wasn't created. This is because
IDT codecs have output amps for digital mics, not input amps, while
input amps should be used for other analog pins. Thus the automatic
capture volume creation should check both directions for digital mics.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
1) Added support of internal subwoofer (it sounds!!!)
2) Auto muting front speakers and internal subwoofer on headphones plug.
3) Internal mic works.
4) 3 channel mods (jack maps):
black pink blue
2ch: front ext mic line in
4ch: front ext mic surround
6ch: front CLFE surround
Can be changed in mixer.
5) Sound can be recorded from:
Internal mic
Ext mic
Cd
Line in
6) 2 separate capture channels.
Signed-off-by: Denis Kuplyakov <dener.kup@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
One more patch to give a better name for the primary output controls,
this time for ALC861-VD codec. The change is simple, just checking the
pin connection whether it's a speaker-out. When both speaker and HP
are assigned, we name the volume as "PCM" as this influences on both
outputs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similar improvements for ALC262 codec like previous two commits:
assign a better name, either Master or Speaker, for the primary output
controls.
However, in the case of ALC262 codec, the necessary changes are larger
than others because we need to check the possibility of different mixer
amps depending on the pins. The pin 0x16 is mono, and bound with the
dedicated mixer 0x0e while other pins are bound with 0x0c. Thus, there
are two possible volumes.
When only one of them is used, we can name it as "Master". OTOH, when
both are used at the same time, they have to be named uniquely.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of fixed "Front" mixer name, try to assign a better name, e.g.
"Master" or "Speaker" fot the primary output volume controls of ALC260
codec.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When there is only one DAC is used for ALC880, try to assign a better
name, either Speaker or Front, depending on the output pin type.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Provide a standard parser for input pins to create the input mixer
and input source controls instead of having a difference one for each
Realtek codec. The new helper parses the codec connections dynamically
isntead of fixed indicies.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reuse a part of the code of ALC268 parser for ALC269.
This will change the default output volume either to Front or Speaker
depending on the pin configuration.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are many variants of Toshiba laptops with ALC268 codec, and
it seems that a few of them don't work with model=toshiba preset
since they have the secondary ALC268 codec just for HDMI output.
This is a regression due to the previous clean-up work to merge all
Toshiba quirk entries into a single check.
This patch adds the identification of such laptops to apply the
standard BIOS-probing method. Unfortunately, Toshiba laptops have
all the same PCI SSID, so we need to check the codec SSID to identify
each device.
Tested-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
