The low-level mlx4 driver modified the page-list addresses for fast
register work requests post send to big-endian, and set a "present"
bit. This caused problems later when the consumer attempted to unmap
the pages using the page-list (using the list addresses which were
assumed to be still in CPU-endian order). Fix the mlx4 driver to
allocate two buffers and use a private buffer for the hardware-format
bus addresses.
This patch fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1571>,
an NFS/RDMA server crash. The cause of the crash was found by Vu Pham
of Mellanox. The fix is along the lines suggested by Steve Wise in
comment #21 in bug 1571.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the SQ is flushed, mark the flushed entries as not signaled so
the poll logic doesn't re-insert the CQ entry thinking its an out of
order completion.
The bug can cause the NFS/RDMA server to crash due to processing the
same completed work request twice.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If reg_phys_mem() fails, we need to free memory allocated for MPA
frame with private data before returning the error. Also move
nes_add_ref() after the reg_phys_mem() is successful.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Running large cluster setup, we are hanging after many hours of
testing. Fixing this required going over the code and making sure the
rexmit entry was properly removed based on the cm_node's state and
packet received. Also when receiving a FIN packet, check seq# and
make sure there were no errors before calling handle_fin().
Following are the changes done in nes_cm.c:
* handle_ack_pkt() needs to return error value, so in case of error,
handle_fin() is not called. Some cleanup done while going over the code.
* handle_rst_pkt(), handling of cm_node's NES_CM_STATE_LAST_ACK is missing.
* process_packet(), in case of FIN only packet is received, call
check_seq() before processing.
* in handle_fin_pkt(), we are calling cleanup_retrans_entry() for all
conditions, even if the packets need to be dropped.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Under heavy load with large cluster testing, it may take longer to
receive a response to MPA requests. Change the driver to wait longer
after each rexmit to max time value.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
check_seq() was not checking if the seq#s have wrapped. Fix it.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a connect request comes, apbvt should only be set for
non-loopback connections.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove the NES_DEBUG that is causing the compile warning about an
unused variable when INFINIBAND_NES_DEBUG is not enabled.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
/sys/class/infiniband/nes?/fw_ver is not displaying firmware version
properly (it shows 0.0.0 with the current code). Fill in the correct
firmware version number.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
With updated PHY firmware for SFP_D, setting the trace length to 1
inch for SFP_D provides a more stable link.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enable repause timer for port 1. Without this setting, under stress,
the chip may misbehave.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In commit 1b949324 ("RDMA/nes: Fix SFP+ PHY initialization") there is
a mistake in the clean up code that removed port 1 CDR loop filter
settings for 10G cards other than CX4. Put the correct setting back
for appropriate PHY types.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change thermo mitigation code to flip the SerDes1 reference clock to
internal, to match the change in commit a4849fc1 ("RDMA/nes: Add
wide_ppm_offset parm for switch compatibility").
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set target can queue limit to the number of preallocated
session tasks we have.
This along with the cxgb3i can_queue patch will fix a throughput
problem where it could only queue one LU worth of data at a time.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In error paths where a CQ is not created, pbl is not freeed properly.
In nes_destroy_cq(), add the corresponding check for nescq->mcrqf to
not call nes_free_resource() when it is already done in nes_create_cq().
Signed-off-by: Miroslaw Walukiewicz <miroslaw.walukiewicz@intel.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commands INIT_HCA, CLOSE_HCA, SYS_EN, SYS_DIS, and CLOSE_IB all have 1
second timeouts. For INIT_HCA this causes problems when had more than
2^18 are QPs configured, since the command takes more than 1 second to
complete.
All other commands have 60-second timeouts. This patch makes the
above commands consistent with the rest of the commands (and with the
chip documentation).
This patch is an expansion of a patch from Arthur Kepner
<akepner@sgi.com> fixing just the INIT_HCA timeout.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
QP attributes must stay initialized when moving back to IDLE. Zeroing
them will crash the system in _flush_qp() if the QP is subsequently
moved to ERROR and back to IDLE.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code incorrectly failed memory registration if the buffer was not
page aligned. Also, the length field is mangled causing the hardware
to think the registration is much larger than it really is.
The fix is to remove the page alignment restriction as well the
incorrect length adjustment. Also make sure that all buffers after
the first start at a page boundary, and all buffers except the last
end on a page boundary.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Initialize pbl_count_256 to 0 to get rid of the warning:
drivers/infiniband/hw/nes/nes_verbs.c: In function 'nes_reg_mr':
drivers/infiniband/hw/nes/nes_verbs.c:1955: warning: 'pbl_count_256' may be used uninitialized in this function
Reported-by: Roland Dreier <rdreier@cisco.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If NAPI is enabled while IPoIB's CQ is being drained, it creates a
race on priv->ibwc between ipoib_poll() and ipoib_drain_cq(), leading
to memory corruption.
The solution is to enable/disable NAPI in ipoib_ib_dev_{open/stop}()
instead of in ipoib_{open/stop}(), and sync NAPI on the INITIALIZED
flag instead on the ADMIN_UP flag. This way NAPI will be disabled when
ipoib_drain_cq() is called.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1587>.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
NFS/RDMA currently fails to set up connections if peer2peer is on.
This is due to the fact that the NFS/RDMA client sets its ORD to 0.
If peer2peer is set, make sure the active side ORD is >= 1 and the
passive side IRD is >=1.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Add support for new SFP+ PHY
RDMA/nes: Add wide_ppm_offset parm for switch compatibility
RDMA/nes: Fix SFP+ PHY initialization
RDMA/nes: Fix nes_nic_cm_xmit() error handling
RDMA/nes: Fix error handling issues
RDMA/nes: Fix incorrect casts on 32-bit architectures
IPoIB: Document newish features
RDMA/cma: Create cm id even when IB port is down
RDMA/cma: Use rate from IPoIB broadcast when joining IPoIB multicast groups
IPoIB: Avoid free_netdev() BUG when destroying a child interface
mlx4_core: Don't leak mailbox for SET_PORT on Ethernet ports
RDMA/cxgb3: Release dependent resources only when endpoint memory is freed.
RDMA/cxgb3: Handle EEH events
IB/mlx4: Use pgprot_writecombine() for BlueFlame pages
Add new register settings for new SFP+ PHY/firmware.
Add new PHY to to nes_netdev_get/set_settings.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We have observed unstable link with a new BNT switch.
Add wide_ppm_offset parameter to allow the user to control the clock
ppm offset on the CX4 interface for better compatibility. Default is
100ppm, setting it to 1 will increase it to 300ppm. Change default
SerDes1 reference clock to external source.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
SFP+ PHY initialization has very long delays, incorrect settings for
direct attach copper cables, and inconsistent link detection.
Adjust delays to the minimum required by the PHY. Worst case is now
less than 4 seconds. Add new register settings for direct attach
cables. Change link detection logic to use two new registers for more
consistent link state detection. Reorganize code to shorten line
length.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We are getting crash or hung situation when we are running network
cable pull tests during RDMA traffic.
In schedule_nes_timer(), we return an error if nes_nic_cm_xmit()
returns failure. This is changed to success as skb is being put on
the timer routines to be processed later. In send_syn() case, we are
indicating connect failure once from nes_connect() and the other when
the rexmit retries expires.
The other issue is skb->users which we are incrementing before calling
nes_nic_cm_xmit() which calls dev_queue_xmit() but in case of failure
we are decrementing the skb->users at the same time putting the skb on
the rexmit path. Even if dev_queue_xmit() fails, the skb->users is
decremented already. We are removing the decrement of skb->users in
case of failure from both schedule_nes_timer() as well as from
nes_cm_timer_tick().
There is also extra check in nes_cm_timer_tick() for rexmit failure
which does a break from the loop is removed. This causes problem as
the other nodes have their cm_node->ref_count incremented and are not
processed.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix issues found by static code analysis:
(1) Check if cm_node was successfully created for loopback connection.
(2) schedule_nes_timer() does not free up allocated memory after
encountering an error. There is a WARN_ON() for this condition.
(3) there is a cm_node->freed flag which is set but not used.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The were some incorrect casts to unsigned long that caused 64-bit values
to be truncated on 32-bit architectures and made the driver pass invalid
adresses and lengths to the hardware. The problems were primarily seen
with kernels with highmem configured but some could show up in
non-highmem kernels, too.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When doing rdma_resolve_addr(), if the relevant IB port is down, the
function fails and the cm_id is not bound to the correct device.
Therefore, application does not have a device handle and cannot wait
for the port to become active. The function fails because the
underlying IPoIB interface is not joined to the broadcast group and
therefore the SA does not have a multicast record to take a Q_Key
from.
The fix is to use lazy Q_Key resolution - cma_set_qkey() will set
id_priv->qkey if it was not set, and will be called just before the
Q_Key is really required.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When joining an IPoIB multicast group, use the same rate as in the
broadcast group. Otherwise, if the RDMA CM creates this group before
IPoIB does, it might get a different rate. This will cause IPoIB to
fail joining to the same group later on, because IPoIB uses strict
rate selection.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We have to release the RTNL before calling free_netdev() so that the
device state has a chance to become NETREG_UNREGISTERED. Otherwise
when removing a child interface, we hit the BUG() that tests the
device state in free_netdev().
Reported-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The cxgb3 l2t entry, hwtid, and dst entry were being released before
all the iwch_ep references were released. This can cause a crash in
t3_l2t_send_slow() and other places where the l2t entry is used.
The fix is to defer releasing these resources until all endpoint
references are gone.
Details:
- move flags field to the iwch_ep_common struct.
- add a flag indicating resources are to be released.
- release resources at endpoint free time instead of close/abort time.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- wrap calls into cxgb3 and fail them if we're in the middle
of a PCI EEH event.
- correctly unwind and release endpoint and other resources when
we are in an EEH event.
- dispatch IB_EVENT_DEVICE_FATAL event when cxgb3 notifies iw_cxgb3 of
a fatal error.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The PAT work on x86 has finally made pgprot_writecombine() a usable API
for modular drivers. As the comment indicates, this is exactly what we
want to use in mlx4_ib to map BlueFlame pages up to userspace, since
using WC for these pages improves small message latency significantly.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When net-next and infiniband were merged upstream, each branch deleted
one of a pair of adjacent lines from nes_nic.c, but when Linus fixed the
conflict up, he brought back both of the lines. Fix up to the intended
final tree state.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1750 commits)
ixgbe: Allow Priority Flow Control settings to survive a device reset
net: core: remove unneeded include in net/core/utils.c.
e1000e: update version number
e1000e: fix close interrupt race
e1000e: fix loss of multicast packets
e1000e: commonize tx cleanup routine to match e1000 & igb
netfilter: fix nf_logger name in ebt_ulog.
netfilter: fix warning in ebt_ulog init function.
netfilter: fix warning about invalid const usage
e1000: fix close race with interrupt
e1000: cleanup clean_tx_irq routine so that it completely cleans ring
e1000: fix tx hang detect logic and address dma mapping issues
bridge: bad error handling when adding invalid ether address
bonding: select current active slave when enslaving device for mode tlb and alb
gianfar: reallocate skb when headroom is not enough for fcb
Bump release date to 25Mar2009 and version to 0.22
r6040: Fix second PHY address
qeth: fix wait_event_timeout handling
qeth: check for completion of a running recovery
qeth: unregister MAC addresses during recovery.
...
Manually fixed up conflicts in:
drivers/infiniband/hw/cxgb3/cxio_hal.h
drivers/infiniband/hw/nes/nes_nic.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (30 commits)
RDMA/cxgb3: Enforce required firmware
IB/mlx4: Unregister IB device prior to CLOSE PORT command
mlx4_core: Add link type autosensing
mlx4_core: Don't perform SET_PORT command for Ethernet ports
RDMA/nes: Handle MPA Reject message properly
RDMA/nes: Improve use of PBLs
RDMA/nes: Remove LLTX
RDMA/nes: Inform hardware that asynchronous event has been handled
RDMA/nes: Fix tmp_addr compilation warning
RDMA/nes: Report correct vendor_id and vendor_part_id
RDMA/nes: Update copyright to new legal entity and year
RDMA/nes: Account for freed PBL after HW operation
IB: Remove useless ibdev_is_alive() tests from sysfs code
IB/sa_query: Fix AH leak due to update_sm_ah() race
IB/mad: Fix ib_post_send_mad() returning 0 with no generate send comp
IB/mad: initialize mad_agent_priv before putting on lists
IB/mad: Fix null pointer dereference in local_completions()
IB/mad: Fix RMPP header RRespTime manipulation
IB/iser: Remove hard setting of path MTU
mlx4_core: Add device IDs for MT25458 10GigE devices
...
The cxgb3 NIC driver can handle more firmware versions than iw_cxgb3,
and since commit 8207befa ("cxgb3: untie strict FW matching") cxgb3
will load with firmware versions that iw_cxgb3 can't handle. The FW
major number indicates a specific interface between the FW and
iw_cxgb3. Thus if the major number of the running firmware does not
match the required version compiled into iw_cxgb3, then iw_cxgb3 must
not register that device.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Also, removed unnecessary memset() since alloc_netdev returns
zeroed memory.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert this driver to new net_device_ops infrastructure.
Also use default net_device get-stats infrastructure
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the ConnectX programmer's reference manual, all
operations should be stopped, all QPs should be torn down and all WQEs
flushed before the CLOSE_PORT command is invoked. In some cases
reversing the order of operations (as implemented now) could cause
a loss of completions.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We do not need to have llds set the host no for the session's
parent, because we know the session's parent is going to be
the host. This removes it from the session creation callback
and converts the drivers.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The qdepth setting was useful when we needed libiscsi to verify
the setting. Now we just need to make sure if older tools
passed in zero then we need to set some default.
So this patch just has us use the sht->cmd_per_lun or if
for LLD does a host per session then we can set it on per
host basis.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We were using the shost work queue which ended up being
a little akward since all iscsi hosts need a thread for
scanning, but only drivers hooked into libiscsi need
a workqueue for transmitting. So this patch moves the
xmit workqueue to the lib.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There is no need to cap the queue depth in the modules. We set
this in userspace and can do that there. For performance testing
with ram based targets, this is helpful since we can have very
high queue depths.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
iser has its own logging inrfastrucutre. Convert it to use
it instead of libiscsi.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
STag zero is a special STag that allows consumers to access any bus
address without registering memory. The nes driver unfortunately
allows STag zero to be used even with QPs created by unprivileged
userspace consumers, which means that any process with direct verbs
access to the nes device can read and write any memory accessible to
the underlying PCI device (usually any memory in the system). Such
access is usually given for cluster software such as MPI to use, so
this is a local privilege escalation bug on most systems running this
driver.
The driver was using STag zero to receive the last streaming mode
data; to allow STag zero to be disabled for unprivileged QPs, the
driver now registers a special MR for this data.
Cc: <stable@kernel.org>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While doing testing, there are failures as MPA Reject call is not
handled. To handle MPA Reject call, following changes are done:
*Handle inbound/outbound MPA Reject response message.
When nes_reject() is called for pending MPA request reply,
send the MPA Reject message to its peer (active
side)cm_node. The peer cm_node (active side) will indicate
Reject message event for the pending Connect Request.
*Handle MPA Reject response message for loopback connections and listener.
When MPA Request is rejected, check if it is a loopback
connection and if it is then it will send Reject message event
to its peer loopback node. Also when destroying listener,
check if the cm_nodes for that listener are loopback or not.
*Add gracefull connection close with the MPA Reject response message.
Send gracefull close (FIN, FIN ACK..) to terminate the cm_nodes.
*Some code re-org while making the above changes.
Removed recv_list and recv_list_lock from the cm_node
structure as there can be only one receive close entry on the
timer. Also implemented handle_recv_entry() as receive close
entry is processed from both nes_rem_ref_cm_node() as well as
nes_cm_timer_tick().
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Two level 256 byte PBLs was not implemented so the driver could report
out of memory when in fact there were PBLs still available.
This solution prefers to use 4KB PBLs over two level 256B PBLs until
the number of 4KB PBLs falls below a threshold. At this point the 4KB
PBL structure is converted to use 256B PBLs which prevents the driver
from running out of 4KB PBLs too quickly.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
NETIF_F_LLTX is deprecated. Remove private TX locking from the driver
and remove the NETIF_F_LLTX feature flag. This also fixes a warning
in some configs that comes from doing skb_linearize() call in the
hard_start_xmit method with IRQs disabled (if HIGHMEM is enabled,
skb_linearize() may end up enabling BHs, which is a no-no if hard IRQs
are disabled in that context). By getting rid of LLTX, we do not
disable IRQs when skb_linearize() is called.
Remove the sq_lock as it is not needed for non-LLTX. Fix ethtool not
to show the counter for sq_lock.
Reported-by: aluno3@poczta.onet.pl
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When asynchronous events are processed by software, it is necessary
to let the hardware know that software has handled the event. This
frees up the entry in the asynchronous event queue.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In find_node(), tmp_addr causes an "unused variable" warning when
INFINIBAND_NES_DEBUG is not defined. It's only used in a nes_debug()
and the print does not make sense. So take out the whole thing.
Reported-by: Manish Katiyar <mkatiyar@gmail.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ibv_devinfo displays 0 for vendor_id and vendor_part_id. Fill in OUI
and device_id for those two fields.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Update copyright to the new legal entity, Intel-NE, Inc., an Intel
company. Update copyright for the new year.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix occurrences where the software PBL counts were changed before the
hardware was updated. This bug allowed another thread to overallocate
the hardware resources.
Add proper PBL accounting in case nes_reg_mr() fails.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some attribute show functions test ibdev_is_alive() to make sure that
it's OK to access device state. However, the sysfs attributes will
not be registered until the device is fully initialized, and they'll
be unregistered before anything is torn down, so ibdev_is_alive()
doesn't do anything useful. Remove it.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Our testing uncovered a race condition in ib_sa_event():
spin_lock_irqsave(&port->ah_lock, flags);
if (port->sm_ah)
kref_put(&port->sm_ah->ref, free_sm_ah);
port->sm_ah = NULL;
spin_unlock_irqrestore(&port->ah_lock, flags);
schedule_work(&sa_dev->port[event->element.port_num -
sa_dev->start_port].update_task);
If two events occur back-to-back (e.g., client-reregister and LID
change), both may pass the spinlock-protected code above before the
scheduled work updates the port->sm_ah handle. Then if the scheduled
work ends up running twice, the second operation will then find a
non-NULL port->sm_ah, and will simply overwrite it in update_sm_ah --
resulting in an AH leak.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If ib_post_send_mad() returns 0, the API guarantees that there will be
a callback to send_buf->mad_agent->send_handler() so that the sender
can call ib_free_send_mad(). Otherwise, the ib_mad_send_buf will be
leaked and the mad_agent reference count will never go to zero and the
IB device module cannot be unloaded. The above can happen without
this patch if process_mad() returns (IB_MAD_RESULT_SUCCESS |
IB_MAD_RESULT_CONSUMED).
If process_mad() returns IB_MAD_RESULT_SUCCESS and there is no agent
registered to receive the mad being sent, handle_outgoing_dr_smp()
returns zero which causes a MAD packet which is at the end of the
directed route to be incorrectly sent on the wire but doesn't cause a
hang since the HCA generates a send completion.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There is a potential race in ib_register_mad_agent() where the struct
ib_mad_agent_private is not fully initialized before it is added to
the list of agents per IB port. This means the ib_mad_agent_private
could be seen before the refcount, spin locks, and linked lists are
initialized. The fix is to initialize the structure earlier.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
handle_outgoing_dr_smp() can queue a struct ib_mad_local_private
*local on the mad_agent_priv->local_work work queue with
local->mad_priv == NULL if device->process_mad() returns
IB_MAD_RESULT_SUCCESS | IB_MAD_RESULT_REPLY and
(!ib_response_mad(&mad_priv->mad.mad) ||
!mad_agent_priv->agent.recv_handler).
In this case, local_completions() will be called with local->mad_priv
== NULL. The code does check for this case and skips calling
recv_mad_agent->agent.recv_handler() but recv == 0 so
kmem_cache_free() is called with a NULL pointer.
Also, since recv isn't reinitialized each time through the loop, it
can cause a memory leak if recv should have been zero.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Remove hard setting of the IB MTU used by iSER's RC queue-pair to 1K,
as this was done due to inter-op issues with an old iser target which
is not used any more.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Move the ib_device_unregister_sysfs() call from ib_dealloc_device() to
ib_unregister_device(). The old code allows device unregister to
proceed even if some sysfs files are open, which leaves a window where
userspace can open a file before a device is removed but then end up
reading the file after the device is removed, which leads to various
kernel crashes either because the device data structure is freed or
because the low-level driver code is gone after module removal.
By not returning from ib_unregister_device() until after all sysfs
entries are removed, we make sure that data structures and/or module
code is not freed until after all sysfs access is done.
Reported-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipath_release_user_pages_on_close() just allocated a structure to
schedule work with but just returned (leaking the structure) rather than
actually doing schedule_work(). Fix the logic to what was intended.
This was spotted by the Coverity checker (CID 2700).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the second vmalloc() fails, the wrong pointer is pased to vfree(), so
the first vmalloc() ends up getting leaked.
This was spotted by the Coverity checker (CID 2709).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Impact: new timer API
Based on an idea from Martin Josefsson with the help of
Patrick McHardy and Stephen Hemminger:
introduce the mod_timer_pending() API which is a mod_timer()
offspring that is an invariant on already removed timers.
(regular mod_timer() re-activates non-pending timers.)
This is useful for the networking code in that it can
allow unserialized mod_timer_pending() timer-forwarding
calls, but a single del_timer*() will stop the timer
from being reactivated again.
Also while at it:
- optimize the regular mod_timer() path some more, the
timer-stat and a debug check was needlessly duplicated
in __mod_timer().
- make the exports come straight after the function, as
most other exports in timer.c already did.
- eliminate __mod_timer() as an external API, change the
users to mod_timer().
The regular mod_timer() code path is not impacted
significantly, due to inlining optimizations and due to
the simplifications.
Based-on-patch-from: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Cc: netdev@vger.kernel.org
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If path_rec_start() returns error, call path_free() only if the path
was newly-created. If we free an existing path whose valid flag was zero,
(but do not detach it from the list) we cause corruption of the
path list (of which it is a member), and get a kernel crash.
The simplest solution is to not free an existing path -- just leave it
in the list as-is (i.e., with its valid flag cleared).
Thanks to Yossi Etigin of Voltaire for identifying the problem flow
which caused the kernel crash.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Moni Shua <monis@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove modulo usage to avoid a divide in the fast path (not all
gcc versions do strength reduction here).
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The poll and flush code needs to handle all send opcodes: SEND,
SEND_WITH_SE, SEND_WITH_INV, and SEND_WITH_SE_INV.
Ignore TERM indications if the connection already gone.
Ignore HW receive completions if the RQ is empty.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The variable 'offset' in iwch_sgl2pbl_map() needs to be a u64.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When snooping a PortInfo MAD, its client_reregister bit is checked.
If the bit is ON then a CLIENT_REREGISTER event is dispatched,
otherwise a LID_CHANGE event is dispatched. This way of decision
ignores the cases where the MAD changes the LID along with an
instruction to reregister (so a necessary LID_CHANGE event won't be
dispatched) or the MAD is neither of these (and an unnecessary
LID_CHANGE event will be dispatched).
This causes problems at least with IPoIB, which will do a "light"
flush on reregister, rather than the "heavy" flush required due to a
LID change.
Fix this by dispatching a CLIENT_REREGISTER event if the
client_reregister bit is set, but also compare the LID in the MAD to
the current LID. If and only if they are not identical then a
LID_CHANGE event is dispatched.
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When snooping a PortInfo MAD, its client_reregister bit is checked.
If the bit is ON then a CLIENT_REREGISTER event is dispatched,
otherwise a LID_CHANGE event is dispatched. This way of decision
ignores the cases where the MAD changes the LID along with an
instruction to reregister (so a necessary LID_CHANGE event won't be
dispatched) or the MAD is neither of these (and an unnecessary
LID_CHANGE event will be dispatched).
This causes problems at least with IPoIB, which will do a "light"
flush on reregister, rather than the "heavy" flush required due to a
LID change.
Fix this by dispatching a CLIENT_REREGISTER event if the
client_reregister bit is set, but also compare the LID in the MAD to
the current LID. If and only if they are not identical then a
LID_CHANGE event is dispatched.
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Freeze activity when notified that the underlying chip
is getting reset on a EEH event or fatal error.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The base versions handle constant folding just fine, use them
directly. The replacements are OK in the include/ files as they are
not exported to userspace so we don't need the __ prefixed versions.
This patch does not affect code generation at all.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ehca_plpar_hcall9() takes an unsigned long array, so make all callers
pass that in. This fixes warnings introduced by commit fe333321
("powerpc: Change u64/s64 to a long long integer type"), which changed
u64 from unsigned long to unsigned long long.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit fe333321 ("powerpc: Change u64/s64 to a long long integer
type") changed u64 from unsigned long to unsigned long long, which
means that printk formats for printing u64 values should use "ll"
instead of "l" to avoid warnings. Fix all the places affected by this
in ehca.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When IPoIB tries to join a multicast group, and the SA module's SM
address handle is NULL (because of an SM change, etc), the join
returns with -EAGAIN status. In that case, don't print an error
message unless multicast debugging is enabled.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The current work request posting code writes the LSO segment before
writing any data segments. This leaves a window where the LSO segment
overwrites the stamping in one cacheline that the HCA prefetches
before the rest of the cacheline is filled with the correct data
segments. When the HCA processes this work request, a local
protection error may result.
Fix this by saving the LSO header size field off and writing it only
after all data segments are written. This fix is a cleaned-up version
of a patch from Jack Morgenstein <jackm@dev.mellanox.co.il>.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1383>.
Reported-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a deadlock between child interface creation/deletion and ipoib
start/stop. The former takes vlan_mutex, and then might take RTNL via
register_netdev()/unregister_netdev(). The latter is executed with
RTNL held, and tries to take vlan_mutex, which can lead to an AB-BA
deadlock.
Fix this by having the child interface creation/deletion code take the
RTNL first so vlan_mutex always nests inside RTNL. We can use
register_netdevice() for child interfaces because we form the
interface name from the parent interface and hence don't need the '%'
expansion of register_netdev().
Reported-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
After commit fe25c561 ("IPoIB: Don't enable NAPI when it's already
enabled"), if an interface is brought up but the corresponding P_Key
never appears, then ipoib_stop() will hang in napi_disable(), because
ipoib_open() returns before it does napi_enable().
Fix this by changing ipoib_open() to call napi_enable() even if the
P_Key isn't present.
Reported-by: Yossi Etigin <yosefe@Voltaire.COM>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/iser: Add dependency on INFINIBAND_ADDR_TRANS
IPoIB: Do not join broadcast group if interface is brought down
RDMA/nes: Fix for NIPQUAD removal
IPoIB: Fix loss of connectivity after bonding failover on both sides
IB/mlx4: Don't register IB device for adapters with no IB ports
mlx4_core: Fix warning from min()
IB/ehca: spin_lock_irqsave() takes an unsigned long
Fix ib_iser build to depend on INFINIBAND_ADDR_TRANS; if INET=y but
IPV6=n, then the RDMA CM is not built but INFINIBAND_ISER can be
enabled, leading to:
ERROR: "rdma_destroy_id" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_connect" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_destroy_qp" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_create_id" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_create_qp" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_resolve_route" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_disconnect" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_resolve_addr" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Because the ipoib_workqueue is not flushed when ipoib interface is
brought down, ipoib_mcast_join() may trigger a join to the broadcast
group after priv->broadcast was set to NULL (during cleanup). This
will cause the system to be a member of the broadcast group when
interface is down. As a side effect, this breaks the optimization of
setting the Q_key only when joining the broadcast group.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit 63779436 ("drivers: replace NIPQUAD()") accidentally replaced
some HIPQUAD()s, causing IP addresses to be printed in reverse order.
Add temporary local vars until the byteswapping can be pushed further
up the stack.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix bonding failover in the case both peers failover and the
gratuitous ARP is lost. In that case, the sender side will create an
ipoib_neigh and issue a path request with the old GID first. When
skb->dst->neighbour->ha changes due to ARP refresh, this ipoib_neigh
will not be added to the path->list of the path of the new GID,
because the ipoib_neigh already exists. It will not have an AH
either, because of sender-side failover. Therefore, it will not get
an AH when the path is resolved.
The solution here is to compare GIDs in ipoib_start_xmit() even if
neigh->ah is invalid. Comparing with an uninitialized value of
neigh->dgid should be fine, since a spurious match is harmless (and
astronomically unlikely too).
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the mlx4_ib driver finds an adapter that has only ethernet ports, the
current code will register an IB device with 0 ports. Nothing useful or
sensible can be done with such a device, so just skip registering it.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When I review ocfs2 code, find there are 2 typos to "successfull". After
doing grep "successfull " in kernel tree, 22 typos found totally -- great
minds always think alike :)
This patch fixes all the similar typos. Thanks for Randy's ack and comments.
Signed-off-by: Coly Li <coyli@suse.de>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
The flags argument to spin_lock_irqsave() should really be unsigned
long. This will also help prevent some warnings when we change u64 to
unsigned long long.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
... and don't bother in callers. Don't bother with zeroing i_blocks,
while we are at it - it's already been zeroed.
i_mode is not worth the effort; it has no common default value.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Fix reading SL field out of cqe->sl_vid
RDMA/addr: Fix build breakage when IPv6 is disabled
Commit f780a9f1 ("mlx4_core: Add ethernet fields to CQE struct")
introduced a bug in how wc->sl is set in mlx4_ib_poll_one() -- since
cqe->sl_vid is a big-endian value, the shift must be done after
converting to host endianness.
This bug was found using sparse endianness checking.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit 38617c64 ("RDMA/addr: Add support for translating IPv6
addresses") broke the build when CONFIG_IPV6=n, because the ib_addr
module unconditionally attempted to call ipv6_chk_addr() and other
IPv6 functions that are not defined when IPv6 is disabled. Fix this
by only building IPv6 support if CONFIG_IPV6 is turned on, and
add a Kconfig dependency to prevent the ib_addr code from being built
in when IPv6 is built modular.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Impact: cleanup
We're moving from handing around cpumask_t's to handing around struct
cpumask *'s. cpus_*, cpumask_t and cpu_*_map are deprecated: convert
to cpumask_*, cpu_*_mask.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ralph Campbell <infinipath@qlogic.com>
Impact: cleanup
We're moving from handing around cpumask_t's to handing around struct
cpumask *'s. cpus_*, cpumask_t and cpu_*_map are deprecated: convert
to cpumask_*, cpu_*_mask.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Tested-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Cc: Christoph Raisch <raisch@de.ibm.com>
Impact: cleanup
In future, accessing cpu numbers beyond nr_cpu_ids (the runtime limit)
will be undefined. We can avoid future problems by using
for_each_online_cpu() here.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Tested-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Cc: Christoph Raisch <raisch@de.ibm.com>
We do not need to allocate a itt for data_out, so this
passes the opcode to the alloc_pdu callout.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This just converts iser to new alloc_pdu api. It still
preallocates the pdu, so there is no difference.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
net: Allow dependancies of FDDI & Tokenring to be modular.
igb: Fix build warning when DCA is disabled.
net: Fix warning fallout from recent NAPI interface changes.
gro: Fix potential use after free
sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
sfc: When disabling the NIC, close the device rather than unregistering it
sfc: SFT9001: Add cable diagnostics
sfc: Add support for multiple PHY self-tests
sfc: Merge top-level functions for self-tests
sfc: Clean up PHY mode management in loopback self-test
sfc: Fix unreliable link detection in some loopback modes
sfc: Generate unique names for per-NIC workqueues
802.3ad: use standard ethhdr instead of ad_header
802.3ad: generalize out mac address initializer
802.3ad: initialize ports LACPDU from const initializer
802.3ad: remove typedef around ad_system
802.3ad: turn ports is_individual into a bool
802.3ad: turn ports is_enabled into a bool
802.3ad: make ntt bool
ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
...
Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
When we removed the network device argument from several
NAPI interfaces in 908a7a16b8
("net: Remove unused netdev arg from some NAPI interfaces.")
several drivers now started getting unused variable warnings.
This fixes those up.
Signed-off-by: David S. Miller <davem@davemloft.net>
When resizing a CQ, when copying over unpolled CQEs from the old CQE
buffer to the new buffer, the ownership bit must be set appropriately
for the new buffer, or the ownership bit in the new buffer gets
corrupted.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There is no lock protecting tx_free_list thus causing a system crash
when skb_dequeue() is called and the list is empty. Since it did not give
any performance boost under heavy load, remove it to simplify the code.
Replace get_free_pkt() with dev_alloc_skb() to allocate MAX_CM_BUFFER skb
for connection establishment/teardown as well as MPA request/response.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Handle AF_INET6 cases where required, and use struct sockaddr_storage
wherever an IPv6 address might be stored.
Signed-off-by: Aleksey Senin <aleksey@alst60.(none)>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for translating AF_INET6 addresses to the IB address
translation service. This requires using struct sockaddr_storage
instead of struct sockaddr wherever an IPv6 address might be stored,
and adding cases to handle IPv6 in addition to IPv4 to the various
translation functions.
Signed-off-by: Aleksey Senin <aleksey@alst60.(none)>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using MSI-X mode, create a completion event queue for each CPU.
Report the number of completion EQs in a new struct mlx4_caps member,
num_comp_vectors, and extend the mlx4_cq_alloc() interface with a
vector parameter so that consumers can specify which completion EQ
should be used to report events for the CQ being created.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
iSCSI/iSER targets may send PDUs without a prior request from the
initiator. RFC 5046 refers to these PDUs as "unexpected". NOP-In PDUs
with itt=RESERVED and Asynchronous Message PDUs occupy this category.
The amount of active "unexpected" PDU's an iSER target may have at any
time is governed by the MaxOutstandingUnexpectedPDUs key, which is not
yet supported.
Currently when an iSER target sends an "unexpected" PDU, the
initiators recv buffer consumed by the PDU is not replaced. If over
initial_post_recv_bufs_num "unexpected" PDUs are received then the
receive queue will run out of receive work requests entirely.
This patch ensures recv buffers consumed by "unexpected" PDUs are
replaced in the next iser_post_receive_control() call.
Signed-off-by: David Disseldorp <ddiss@sgi.com>
Signed-off-by: Ken Sandars <ksandars@sgi.com>
Acked-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
vpage is checked not to be NULL just after it is initialized at the
beginning of each loop iteration.
A simplified version of the semantic patch that makes this change is
as follows: (http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
expression E;
position p1,p2;
@@
if (x@p1 == NULL || ...) { ... when forall
return ...; }
... when != \(x=E\|x--\|x++\|--x\|++x\|x-=E\|x+=E\|x|=E\|x&=E\|&x\)
(
x@p2 == NULL
|
x@p2 != NULL
)
// another path to the test that is not through p1?
@s exists@
local idexpression r.x;
position r.p1,r.p2;
@@
... when != x@p1
(
x@p2 == NULL
|
x@p2 != NULL
)
@fix depends on !s@
position r.p1,r.p2;
expression x,E;
statement S1,S2;
@@
(
- if ((x@p2 != NULL) || ...)
S1
|
- if ((x@p2 == NULL) && ...) S1
|
- BUG_ON(x@p2 == NULL);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
With the latest flush error completion patch we introduced modulus
operation to calculate the next index within a qmap. Based on
comments from other mailing lists we decided to optimize this
operation by using an addition and an if-statement instead of modulus,
even though this is on the error path.
Signed-off-by: Stefan Roscher <stefan.roscher@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fixes timing race resulting in panic. Not a performance sensitive path.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipath_piobufbase was a single value offset, but is multiple values on
newer chips, so use only the 32 bits for the 2K buffers (4K buffers
are currently used only by the driver).
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Implement the ignoring of ibsymbol errors and linkrecover errors while
the link is at less than INIT (long needed), to get accurate counts.
Particularly an issue when doing non-IBTA DDR negotiation with chips
from vendors that do not support IBTA mode negotiation. If the driver
is unloaded, and there is a delta, the adjusted counters are written
back to the chip, so they stay adjusted across driver reload.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This fixes an obvious oversight where the return value is not checked
for error.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The PSN of the first packet after an RDMA read is based on the size of
the RDMA read request. This is calculated correctly for the WQE sent
after the first request message but not on subsequent requests if the
RDMA read is resent.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Wrap NES_DEBUG and assert macros with do while (0) to avoid ambiguous
else. No one is using sk_buff * returned from form_cm_frame(), so
drop the return. drop_packet() should not be incrementing reset
counter on receiving a FIN.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Between the first empty list check and locking the list, the list can
change. Check it again after it is locked to make sure the list is
still not empty.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ANVL testing showed we are not handling all cm_node states during
connection establishment. Add missing state handlers and fix sequence
number send reset in handle_tcp_options().
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Under heavy traffic, there is a small windows when an APBVT entry is
not yet removed and a new connection is established. Packets for the
new connection are dropped until APBVT entry is removed. This patch
will forward the packets instead of dropping them.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In passive open, after indicating MPA request to rdma_cm, an incoming
RST would fire a reset event to rdma_cm causing it to crash, since the
current state is not connected. The solution is to wait for
nes_accept() or nes_reject() before firing the reset event. If
nes_accept() or nes_reject() is already done, then the reset event
will be fired when RST is processed.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
While processing connected_nodes list, we would release the lock when
we need to send reset to remote partner. That created a window where
the list can be modified. Change this into a two step process: place
nodes that need processing on a local list then process the local list.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use nes_free_cqp_request() instead of open coding. Change some
continue to break in nes_cm_timer_tick, because send_entry used to be
a list processed in a loop (so continue went to the next item). Now
it is a single item, so using break is correct.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Receive work queue entries are checked for L_Key validity, and
pointers to the memory region structure are saved in an allocated
structure. For UD loopback packets, this structure is allocated and
freed for each packet. This patch changes that to allocate/free
during QP creation and destruction.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The return from lookup_one_len() is assigned to *dentry, so that's
what we should be checking with IS_ERR().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
shca_list_lock is taken from softirq context in ehca_poll_eqs, so we
need to lock IRQ safe elsewhere. Found by lockdep.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
