aha/arch/arm/mach-ixp4xx/Makefile
Rod Whitby 7e36e2f535 [ARM] 4874/2: ixp4xx: Add support for the Freecom FSG-3 board
The Freecom-FSG3 is a small network-attached-storage device with the
following feature set:

* Intel IXP422
* 4MB Flash (ixp4xx flash driver)
* 64MB RAM
* 4 USB 2.0 host ports (ehci and ohci drivers)
* 1 WAN (eth1) and 3 LAN (eth0) ethernet ports
  * Supported by the open source ixp4xx ethernet driver
* Via VT6421 disk controller (libata and sata-via drivers)
  * Internal hard disk (PATA supported, SATA not yet supported)
  * External SATA port (not yet supported)
* ISL1208 RTC chip
* Winbond 83782 temp sensor and fan controller
* MiniPCI slot

The ixp4xx_defconfig is also updated to support this device (the
leds-fsg driver is to be submitted separately via the leds tree after
this initial support is merged, as it depends on header gpio defines).

Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-04 10:03:59 +01:00

36 lines
1.2 KiB
Makefile

#
# Makefile for the linux kernel.
#
obj-pci-y :=
obj-pci-n :=
obj-pci-$(CONFIG_ARCH_IXDP4XX) += ixdp425-pci.o
obj-pci-$(CONFIG_MACH_AVILA) += avila-pci.o
obj-pci-$(CONFIG_MACH_IXDPG425) += ixdpg425-pci.o
obj-pci-$(CONFIG_ARCH_ADI_COYOTE) += coyote-pci.o
obj-pci-$(CONFIG_MACH_GTWX5715) += gtwx5715-pci.o
obj-pci-$(CONFIG_MACH_NSLU2) += nslu2-pci.o
obj-pci-$(CONFIG_MACH_NAS100D) += nas100d-pci.o
obj-pci-$(CONFIG_MACH_DSMG600) += dsmg600-pci.o
obj-pci-$(CONFIG_MACH_GATEWAY7001) += gateway7001-pci.o
obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o
obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o
obj-y += common.o
obj-$(CONFIG_ARCH_IXDP4XX) += ixdp425-setup.o
obj-$(CONFIG_MACH_AVILA) += avila-setup.o
obj-$(CONFIG_MACH_IXDPG425) += coyote-setup.o
obj-$(CONFIG_ARCH_ADI_COYOTE) += coyote-setup.o
obj-$(CONFIG_MACH_GTWX5715) += gtwx5715-setup.o
obj-$(CONFIG_MACH_NSLU2) += nslu2-setup.o
obj-$(CONFIG_MACH_NAS100D) += nas100d-setup.o
obj-$(CONFIG_MACH_DSMG600) += dsmg600-setup.o
obj-$(CONFIG_MACH_GATEWAY7001) += gateway7001-setup.o
obj-$(CONFIG_MACH_WG302V2) += wg302v2-setup.o
obj-$(CONFIG_MACH_FSG) += fsg-setup.o
obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o
obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o
obj-$(CONFIG_IXP4XX_NPE) += ixp4xx_npe.o