mirror of
https://github.com/adulau/aha.git
synced 2024-12-28 03:36:19 +00:00
42d399e418
There have accumulated quite a lot of them after the code reorganizations... In several cases I had to replace #include <linux/dma-mapping.h> which wasn't needed directly but happened to #include <linux/err.h> which was needed. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
97 lines
2.7 KiB
C
97 lines
2.7 KiB
C
/*
|
|
* TI DaVinci serial driver
|
|
*
|
|
* Copyright (C) 2006 Texas Instruments.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
|
|
*
|
|
*/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/init.h>
|
|
#include <linux/serial_8250.h>
|
|
#include <linux/serial_reg.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/clk.h>
|
|
#include <linux/io.h>
|
|
|
|
#include <mach/serial.h>
|
|
#include <mach/cputype.h>
|
|
|
|
static inline unsigned int serial_read_reg(struct plat_serial8250_port *up,
|
|
int offset)
|
|
{
|
|
offset <<= up->regshift;
|
|
return (unsigned int)__raw_readl(IO_ADDRESS(up->mapbase) + offset);
|
|
}
|
|
|
|
static inline void serial_write_reg(struct plat_serial8250_port *p, int offset,
|
|
int value)
|
|
{
|
|
offset <<= p->regshift;
|
|
__raw_writel(value, IO_ADDRESS(p->mapbase) + offset);
|
|
}
|
|
|
|
static void __init davinci_serial_reset(struct plat_serial8250_port *p)
|
|
{
|
|
unsigned int pwremu = 0;
|
|
|
|
serial_write_reg(p, UART_IER, 0); /* disable all interrupts */
|
|
|
|
/* reset both transmitter and receiver: bits 14,13 = UTRST, URRST */
|
|
serial_write_reg(p, UART_DAVINCI_PWREMU, pwremu);
|
|
mdelay(10);
|
|
|
|
pwremu |= (0x3 << 13);
|
|
pwremu |= 0x1;
|
|
serial_write_reg(p, UART_DAVINCI_PWREMU, pwremu);
|
|
|
|
if (cpu_is_davinci_dm646x())
|
|
serial_write_reg(p, UART_DM646X_SCR,
|
|
UART_DM646X_SCR_TX_WATERMARK);
|
|
}
|
|
|
|
int __init davinci_serial_init(struct davinci_uart_config *info)
|
|
{
|
|
int i;
|
|
char name[16];
|
|
struct clk *uart_clk;
|
|
struct davinci_soc_info *soc_info = &davinci_soc_info;
|
|
struct device *dev = &soc_info->serial_dev->dev;
|
|
struct plat_serial8250_port *p = dev->platform_data;
|
|
|
|
/*
|
|
* Make sure the serial ports are muxed on at this point.
|
|
* You have to mux them off in device drivers later on if not needed.
|
|
*/
|
|
for (i = 0; i < DAVINCI_MAX_NR_UARTS; i++, p++) {
|
|
if (!(info->enabled_uarts & (1 << i)))
|
|
continue;
|
|
|
|
sprintf(name, "uart%d", i);
|
|
uart_clk = clk_get(dev, name);
|
|
if (IS_ERR(uart_clk))
|
|
printk(KERN_ERR "%s:%d: failed to get UART%d clock\n",
|
|
__func__, __LINE__, i);
|
|
else {
|
|
clk_enable(uart_clk);
|
|
p->uartclk = clk_get_rate(uart_clk);
|
|
davinci_serial_reset(p);
|
|
}
|
|
}
|
|
|
|
return platform_device_register(soc_info->serial_dev);
|
|
}
|