* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
netxen: update copyright
netxen: fix tx timeout recovery
netxen: fix file firmware leak
netxen: improve pci memory access
netxen: change firmware write size
tg3: Fix return ring size breakage
netxen: build fix for INET=n
cdc-phonet: autoconfigure Phonet address
Phonet: back-end for autoconfigured addresses
Phonet: fix netlink address dump error handling
ipv6: Add IFA_F_DADFAILED flag
net: Add DEVTYPE support for Ethernet based devices
mv643xx_eth.c: remove unused txq_set_wrr()
ucc_geth: Fix hangs after switching from full to half duplex
ucc_geth: Rearrange some code to avoid forward declarations
phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
drivers/net/phy: introduce missing kfree
drivers/net/wan: introduce missing kfree
net: force bridge module(s) to be GPL
Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
...
Fixed up trivial conflicts:
- arch/x86/include/asm/socket.h
converted to <asm-generic/socket.h> in the x86 tree. The generic
header has the same new #define's, so that works out fine.
- drivers/net/tun.c
fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
switched over to using 'tun->socket.sk' instead of the redundantly
available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
to the TUN driver") which added a new 'tun->sk' use.
Noted in 'next' by Stephen Rothwell.
Reported by Michael Guntsche <mike@it-loops.com>
--------------------
Commit
38bddf04bc gianfar: gfar_remove needs to call unregister_netdev()
breaks the build of the gianfar driver because "dev" is undefined in
this function. To quickly test rc9 I changed this to priv->ndev but I do
not know if this is the correct one.
--------------------
Signed-off-by: David S. Miller <davem@davemloft.net>
If vlan has been enabled. ifdown followed by ifup will lost hardware
related state.
Also remove duplicated operation in gfar_vlan_rx_register().
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit fe192a4911 ("Rework gianfar
driver to use of_mdio infrastructure") the fixed-link support is
broken, the driver oopses at init_phy():
Unable to handle kernel paging request for data at address 0x000000e4
Faulting instruction address: 0xc01cf298
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c01cf298] init_phy+0x80/0xdc
LR [c01cf250] init_phy+0x38/0xdc
Call Trace:
[cf81fe80] [c01d1cf8] gfar_enet_open+0x6c/0x19c
[cf81fea0] [c024494c] dev_open+0xfc/0x134
[cf81fec0] [c0242edc] dev_change_flags+0x84/0x1ac
[cf81fee0] [c0399ee0] ic_open_devs+0x168/0x2d8
[cf81ff20] [c039b2e8] ip_auto_config+0x90/0x2a4
[cf81ff60] [c0003884] do_one_initcall+0x34/0x1a8
This patch fixes the oops, and removes phy_node checks, and adds a call
to of_phy_connect_fixed_link() if a phy isn't attached..
Also, remove an old fixed-link code that we don't use any longer.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of it was converted to %pM, but the variable
stuck -- remove it now to not cause spurious warnings.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev() used to install default implementations of these
operations, but they must now be explicitly installed in struct
net_device_ops.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 0fd56bb5be ("gianfar:
Add support for skb recycling"), gianfar puts skbuffs that are in
the rx ring back onto the recycle list as-is in case there was a
receive error, but this breaks the following invariant: that all
skbuffs on the recycle list have skb->data = skb->head + NET_SKB_PAD.
The RXBUF_ALIGNMENT realignment done in gfar_new_skb() will be done
twice on skbuffs recycled in this way, causing there not to be enough
room in the skb anymore to receive a full packet, eventually leading
to an skb_over_panic from gfar_clean_rx_ring() -> skb_put().
Resetting the skb->data pointer to skb->head + NET_SKB_PAD before
putting the skb back onto the recycle list restores the mentioned
invariant, and should fix this issue.
Reported-by: Michael Guntsche <mike@it-loops.com>
Tested-by: Michael Guntsche <mike@it-loops.com>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
cacheable_memzero() is completely overkill for the clearing out the FCB
block which is only 8-bytes. The compiler should easily optimize this
with memset. Additionally, cacheable_memzero() only exists on ppc32 and
thus breaks builds of gianfar on ppc64.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch simplifies the driver by making use of more common code.
Tested on Freescale MPC8349emitxgp eval board
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code that was added to increase headroom was wrong.
It doesn't handle the case where gfar_add_fcb() changes the skb.
Better to do check at start of transmit (outside of lock), where
error handling is better anyway.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gianfar uses a hardware header FCB for offloading. However when used
with bridging or IP forwarding, TX skb might not have enough headroom
for the FCB. Reallocate skb for such cases.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 4826857f1b ("gianfar: pass the
proper dev to DMA ops") introduced this build breakage:
CC drivers/net/gianfar.o
drivers/net/gianfar.c: In function 'gfar_suspend':
drivers/net/gianfar.c:552: error: 'struct gfar_private' has no member named 'dev'
drivers/net/gianfar.c: In function 'gfar_resume':
drivers/net/gianfar.c:601: error: 'struct gfar_private' has no member named 'dev'
make[2]: *** [drivers/net/gianfar.o] Error 1
Fix this by converting suspend and resume routines to use
gfar_private->ndev.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to be passing the of_platform device struct into the DMA ops as
its the one that has the archdata setup to know which low-level DMA ops we
should be using (not the net_device one). This isn't an issue until we
expect the archdata to be setup correctly.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a wrong check on num_txbdfree. It could lead to
num_txbdfree become nagative. Result was that the gianfar stops
sending data.
Changes from first version :
- removed a space between parens (David Millers comment)
- full email address in signed off line
Signed-off-by: Rini van Zetten <rini@arvoo.nl>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ira Snyder found that commit 8c7396aebb
"gianfar: Merge Tx and Rx interrupt for scheduling clean up ring" can
cause hangs. It's because there was removed clearing of interrupts in
gfar_schedule_cleanup() (which is called by an interrupt handler) in
case when netif scheduling has been disabled. This patch brings back
this action and a comment.
Reported-by: Ira Snyder <iws@ovro.caltech.edu>
Reported-by: Peter Korsgaard <jacmet@sunsite.dk>
Bisected-by: Ira Snyder <iws@ovro.caltech.edu>
Tested-by: Peter Korsgaard <jacmet@sunsite.dk>
Tested-by: Ira Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stashing is only supported on the 85xx (e500-based) SoCs. The 83xx and 86xx
chips don't have a proper cache for this. U-Boot has been updated to add
stashing properties to the device tree nodes of gianfar devices on 85xx. So
now we modify Linux to keep stashing off unless those properties are there.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO bus drivers for the UCC and gianfar ethernet controllers are
essentially the same. There's no reason to duplicate that much code.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SOFT_RESET must be asserted for at least 3 TX clocks in order for it to work
properly. The syncs in the gfar_write() commands have been hiding this, but
we need to guarantee it.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes following sparse warnings:
CHECK gianfar_ethtool.c
gianfar_ethtool.c:610:26: warning: symbol 'gfar_ethtool_ops' was not declared. Should it be static?
CHECK gianfar_mii.c
gianfar_mii.c:108:35: warning: cast adds address space to expression (<asn:2>)
gianfar_mii.c:119:35: warning: cast adds address space to expression (<asn:2>)
gianfar_mii.c:128:35: warning: cast adds address space to expression (<asn:2>)
gianfar_mii.c:272:5: warning: cast removes address space of expression
gianfar_mii.c:271:15: warning: cast adds address space to expression (<asn:2>)
gianfar_mii.c:340:11: warning: cast adds address space to expression (<asn:2>)
CHECK gianfar_sysfs.c
gianfar_sysfs.c:84:1: warning: symbol 'dev_attr_bd_stash' was not declared. Should it be static?
gianfar_sysfs.c:133:1: warning: symbol 'dev_attr_rx_stash_size' was not declared. Should it be static?
gianfar_sysfs.c:175:1: warning: symbol 'dev_attr_rx_stash_index' was not declared. Should it be static?
gianfar_sysfs.c:213:1: warning: symbol 'dev_attr_fifo_threshold' was not declared. Should it be static?
gianfar_sysfs.c:250:1: warning: symbol 'dev_attr_fifo_starve' was not declared. Should it be static?
gianfar_sysfs.c:287:1: warning: symbol 'dev_attr_fifo_starve_off' was not declared. Should it be static?
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements wakeup management for the gianfar driver.
The driver should set wakeup enable if WOL is enabled, so that
phylib won't power off an attached PHY.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 77ecaf2d5a ("gianfar: Fix VLAN
HW feature related frame/buffer size calculation") wrongly removed
priv->vlgrp assignment, and now priv->vlgrp is always NULL.
This patch fixes the issue, plus fixes following sparse warning
introduced by the same commit:
gianfar.c:1406:13: warning: context imbalance in 'gfar_vlan_rx_register' - wrong count at exit
gfar_vlan_rx_register() checks for "if (old_grp == grp)" and tries
to return w/o dropping the lock.
According to net/8021q/vlan.c VLAN core issues rx_register() callback:
1. In register_vlan_dev() only on a newly created group;
2. In unregister_vlan_dev() only if the group becomes empty.
Thus the check in the gianfar driver isn't needed.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the same kind of wrapper that can also be found in many
other network device drivers.
Tested with a freescale MPC8349E host CPU:
Toggled the interface LEDs on a DP83865 PHY.
Signed-off-by: Clifford Wolf <clifford@clifford.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b31a1d8b41 ("gianfar: Convert
gianfar to an of_platform_driver") went back to using BUS_ID_SIZE
instead of sizeof() as per the larger patch series that will remove
"char bus_id[20]" from struct device.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing the link between 100Mbps and 1Gbps in SGMII mode it was
found out that the link would stop working. The issue is that ECNTRL[R100]
needs to be cleared when in 1Gbps mode. Older reference manuals didn't
require the explicitly clearing but has since been found it that it is
needed.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gfar_poll would declare polling done once the rx queue was empty,
but the tx queue could still have packets left.
Stolen mostly from the e1000 driver.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No clean up function is executed in the interrupt context by this patch.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interface name (ex. eth0) is used as the prefix for the interrupt name,
with _rx, _tx, and _er appended to distinguish multiple interrupts on
the same interface.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scatter Gather support in gianfar driver to handle fragmented frames on
the transmit side.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch which fixed gianfar so it drops packets when it runs out
of memory left in the code which frees the skb when it drops packets.
Change the code so that we only free the skb if the new skb was successfully
created.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever we want to update the status field in a BD, we usually want to
update the length field, too. By combining them into one 32-bit field, we
reduce the number of stores to memory shared with the controller, and we
eliminate the need for order-enforcement, as the length and "READY" bit are
now updated atomically at the same time.
Signed-off-by: Dai Haruki <Dai.Haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is based strongly on code from Dai Haruki <Dai.Haruki@freescale.com>.
The gianfar Buffer Descriptors are arranged in a circular array, the end of
which is denoted by setting the "WRAP" bit in the descriptor. However, the
software knows the end of the ring because it knows how many descriptors are
there. Rather than check each descriptor for whether the WRAP bit is set,
use pointer math to determine where the next BD is. This is also useful for
when we want to look at BDs other than the very next one (for Scatter-Gather).
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
