An earlier patch from Jens Osterkamp attempted to fix GDB
watchpoints by enabling the DABRX register at boot time.
Unfortunately, this did not work on SMP setups, where
secondary CPUs were still using the power-on DABRX value.
This introduces the same change for secondary CPUs on cell
as well.
Reported-by: Ulrich Weigand <Ulrich.Weigand@de.ibm.com>
Tested-by: Ulrich Weigand <Ulrich.Weigand@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Kexec/kdump currently fails on the IBM QS2x blades when the kexec happens
on a CPU other than the initial boot CPU. It turns out that this is the
result of mpic_init trying to set affinity of each interrupt vector to the
current boot CPU.
As far as I can tell, the same problem is likely to exist on any
secondary MPIC, because they have to deliver interrupts to the first
output all the time. There are two potential solutions for this: either
not set up affinity at all for secondary MPICs, or assume that a single
CPU output is connected to the upstream interrupt controller and hardcode
affinity to that per architecture.
This patch implements the second approach, defaulting to the first output.
Currently, all known secondary MPICs are routed to their upstream port
using the first destination, so we hardcode that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The MSI capture logic for the axon bridge can sometimes
lose interrupts in case of high DMA and interrupt load,
when it signals an MSI interrupt to the MPIC interrupt
controller while we are already handling another MSI.
Each MSI vector gets written into a FIFO buffer in main
memory using DMA, and that DMA access is normally flushed
by the actual interrupt packet on the IOIF. An MMIO
register in the MSIC holds the position of the last
entry in the FIFO buffer that was written. However,
reading that position does not flush the DMA, so that
we can observe stale data in the buffer.
In a stress test, we have observed the DMA to arrive
up to 14 microseconds after reading the register.
This patch works around this problem by retrying the
access to the FIFO buffer.
We can reliably detect the conditioning by writing
an invalid MSI vector into the FIFO buffer after
reading from it, assuming that all MSIs we get
are valid. After detecting an invalid MSI vector,
we udelay(1) in the interrupt cascade for up to
100 times before giving up.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I got a bug report about a distro kernel not booting on a particular
machine. It would freeze during boot:
> ...
> Could not find start_pfn for node 1
> [boot]0015 Setup Done
> Built 2 zonelists in Node order, mobility grouping on. Total pages: 123783
> Policy zone: DMA
> Kernel command line:
> [boot]0020 XICS Init
> [boot]0021 XICS Done
> PID hash table entries: 4096 (order: 12, 32768 bytes)
> clocksource: timebase mult[7d0000] shift[22] registered
> Console: colour dummy device 80x25
> console handover: boot [udbg0] -> real [hvc0]
> Dentry cache hash table entries: 1048576 (order: 7, 8388608 bytes)
> Inode-cache hash table entries: 524288 (order: 6, 4194304 bytes)
> freeing bootmem node 0
I've reproduced this on 2.6.27.7. It is caused by commit
8f64e1f2d1 ("powerpc: Reserve in bootmem
lmb reserved regions that cross NUMA nodes").
The problem is that Jon took a loop which was (in pseudocode):
for_each_node(nid)
NODE_DATA(nid) = careful_alloc(nid);
setup_bootmem(nid);
reserve_node_bootmem(nid);
and broke it up into:
for_each_node(nid)
NODE_DATA(nid) = careful_alloc(nid);
setup_bootmem(nid);
for_each_node(nid)
reserve_node_bootmem(nid);
The issue comes in when the 'careful_alloc()' is called on a node with
no memory. It falls back to using bootmem from a previously-initialized
node. But, bootmem has not yet been reserved when Jon's patch is
applied. It gives back bogus memory (0xc000000000000000) and pukes
later in boot.
The following patch collapses the loop back together. It also breaks
the mark_reserved_regions_for_nid() code out into a function and adds
some comments. I think a huge part of introducing this bug is because
for loop was too long and hard to read.
The actual bug fix here is the:
+ if (end_pfn <= node->node_start_pfn ||
+ start_pfn >= node_end_pfn)
+ continue;
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, some PCIe devices on POWER6 machines do not get interrupts
assigned correctly. The problem is that OF doesn't create an
"interrupt" property for them. The fix is for of_irq_map_pci to fall
back to using the value in the PCI interrupt-pin register in config
space, as we do when there is no OF device-tree node for the device.
I have verified that this works fine with a pair of Squib-E SAS
adapter on a P6-570.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
parisc: struct device - replace bus_id with dev_name(), dev_set_name()
parisc: fix kernel crash when unwinding a userspace process
parisc: __kernel_time_t is always long
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: prevent divide by zero error in cpu_avg_load_per_task, update
sched, cpusets: fix warning in kernel/cpuset.c
sched: prevent divide by zero error in cpu_avg_load_per_task
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
irq.h: fix missing/extra kernel-doc
genirq: __irq_set_trigger: change pr_warning to pr_debug
irq: fix typo
x86: apic honour irq affinity which was set in early boot
genirq: fix the affinity setting in setup_irq
genirq: keep affinities set from userspace across free/request_irq()
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: always define DECLARE_PCI_UNMAP* macros
x86: fixup config space size of CPU functions for AMD family 11h
x86, bts: fix wrmsr and spinlock over kmalloc
x86, pebs: fix PEBS record size configuration
x86, bts: turn macro into static inline function
x86, bts: exclude ds.c from build when disabled
arch/x86/kernel/pci-calgary_64.c: change simple_strtol to simple_strtoul
x86: use limited register constraint for setnz
xen: pin correct PGD on suspend
x86: revert irq number limitation
x86: fixing __cpuinit/__init tangle, xsave_cntxt_init()
x86: fix __cpuinit/__init tangle in init_thread_xstate()
oprofile: fix an overflow in ppro code
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: Save/restore HWS_PGA on suspend/resume
drm: move drm vblank initialization/cleanup to driver load/unload
drm/i915: execbuffer pins objects, no need to ensure they're still in the GTT
drm/i915: Always read pipestat in irq_handler
drm/i915: Subtract total pinned bytes from available aperture size
drm/i915: Avoid BUG_ONs on VT switch with a wedged chipset.
drm/i915: Remove IMR masking during interrupt handler, and restart it if needed.
drm/i915: Manage PIPESTAT to control vblank interrupts instead of IMR.
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] powernow-k8: ignore out-of-range PstateStatus value
[CPUFREQ] Documentation: Add Blackfin to list of supported processors
A very minor patch on ramfs-rootfs-initramfs.txt: update the location
where CONFIG_INITRAMFS_SOURCE lives in menuconfig
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Check model for Dell 92HD73xx laptops
ALSA: hda - mark Dell studio 1535 quirk
ALSA: hda - No 'Headphone as Line-out' swich without line-outs
ALSA: hda - Fix AFG power management on IDT 92HD* codecs
ALSA: hda - Fix caching of SPDIF status bits
ALSA: hda - Add a quirk for Dell Studio 15
ALSA: hda: Add STAC_DELL_M4_3 quirk
sound/sound_core: Fix sparse warnings
ALSA: hda: STAC_DELL_M6 EAPD
* 'linux-next' of git://git.infradead.org/~dedekind/ubi-2.6:
UBI: Don't exit from ubi_thread until kthread_should_stop() is true
UBI: fix EBADMSG handling
Compress a set of consecutive switch cases into a case-range.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
toshiba_acpi: close race in toshiba_acpi driver
ACPICA: disable _BIF warning
ACPI: delete OSI(Linux) DMI dmesg spam
ACPICA: Allow _WAK method to return an Integer
ACPI: thinkpad-acpi: fix fan sleep/resume path
sony-laptop: printk tweak
sony-laptop: brightness regression fix
Revert "ACPI: don't enable control method power button as wakeup device when Fixed Power button is used"
ACPI suspend: Blacklist boxes that require us to set SCI_EN directly on resume
ACPI: scheduling in atomic via acpi_evaluate_integer ()
ACPI: battery: Convert discharge energy rate to current properly
ACPI: EC: count interrupts only if called from interrupt handler.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - add support for new USB Tablet PCs
Input: replace spin_lock_bh with spin_lock_irqsave in ml_ff_playback
Input: i8042 - add Compal Hel80 laptop to nomux blacklist
Input: cm109 - add keymap for ATCom AU-100 phone
Input: fix the example of an input device driver
Input: psmouse - fix incorrect validate_byte check in OLPC protocol
Input: atkbd - cancel delayed work before freeing its structure
Input: atkbd - add keymap quirk for Inventec Symphony systems
Input: i8042 - add Dell XPS M1530 to nomux list
Input: elo - fix format string in elo driver
All architectures now use the generic compat_sys_ptrace, as should every
new architecture that needs 32bit compat (if we'll ever get another).
Remove the now superflous __ARCH_WANT_COMPAT_SYS_PTRACE define, and also
kill a comment about __ARCH_SYS_PTRACE that was added after
__ARCH_SYS_PTRACE was already gone.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ml_ff_playback() uses spin_(un)lock_bh. However this function is called
with interrupts disabled from erase_effect() in drivers/input/ff-core.c:196.
This is not permitted, and will result in a WARN_ON in the bottom half handling code.
This patch changes this function to just use spin_lock_irqsave() instead, solving
the problem and simplifying the locking logic.
This was reported as entry #106559 in kerneloops.org
Reported-by: kerneloops.org
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Same as for hotplug_cpu - we want static notifier_block in there in meminitdata,
to avoid false positives whenever it's used.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... by giving the instances' names magic suffix recognized by modpost ;-/
Their ->probe() is __devinit
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... so get xen-ops.h in agreement with xen/smp.c
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
for fsck sake, it's used only when parsing kernel command line...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
a) hisax_init_pcmcia() needs to be defined only if we have
CONFIG_HOTPLUG (no PCMCIA support otherwise) and can be declared
__devinit.
b) HiSax_inithardware() can go __init
c) hisax_register() is passing to checkcard() full-blown hisax_cs_setup_card():
checkcard(i, id, NULL, hisax_d_if->owner, hisax_cs_setup_card);
The problem with it is that
* hisax_cs_setup_card() is __devinit
* hisax_register() is not
* hisax_cs_setup_card() is a switch from hell, calling a lot of
setup_some_weirdcard() depending on card->typ. _These_ are also
__devinit.
However, in hisax_register() we have card->typ equal to
ISDN_CTYPE_DYNAMIC, which reduces hisax_cs_setup_card() to "nevermind
all that crap, just do nothing and return 2". So we add a
trimmed-down callback doing just that and passed to checkcard() by
hisax_register(). _This_ is non-init (we can stand the impact on
.text size).
Voila - no section warnings from drivers/isdn
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'aperture' is declared devinitdata (the whole word of it) and
is used from ->fetch_size() which can, AFAICS, be used on
!HOTPLUG after init time.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
functions calling devinit and called only from devinit
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
a) ->probe() can be __devinit; no need to put it into .text
b) calling __init stuff from it, OTOH, is wrong
c) ->remove() is __devexit fodder
Acked-by: rmk+kernel@arm.linux.org.uk
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
usual "introduce .text.head, put it in front of TEXT_TEXT in vmlinux.lds.S,
make the stuff up to jump to start_kernel live in it", same as on other
targets.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ibmtr_resume() is calling ibmtr_probe(), which is devinit. Whether
that's the right thing to do there is a separate question, but
since it's PCMCIA and thus will never compile without HOTPLUG...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ixgbe_init_interrupt_scheme() is called from ixgbe_resume(). Build that
with CONFIG_PM and without CONFIG_HOTPLUG and you've got a problem.
Several helpers called by it also are misannotated __devinit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* rackmeter_remove() reference needs devexit_p
* rackmeter_setup() is calls devinit and is called only from devinit
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PCI side of driver should be devinit, not init
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
switch to __init for those; unlike powerpc sparc has no hotplug support
for that stuff and their ->probe() tends to call __init functions while
being declared __devinit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code
if (shost->dma_channel != NO_ISA_DMA)
free_dma(shost->dma_channel);
in there is triggerable only if we have CONFIG_ISA (we only set ->dma_channel to
something other than NO_ISA_DMA under #ifdef CONFIG_ISA). OTOH, free_dma() is
not guaranteed to be there in absense of CONFIG_ISA. IOW, driver runs into
undefined symbols on PCI-but-not-ISA configs (e.g. on frv) and it's a false
positive.
Fix: put the entire if () under #ifdef CONFIG_ISA; behaviour doesn't change and
dependency on free_dma() disappears for !CONFIG_ISA.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Uses clk_...() a lot
Acked-by: rmk+kernel@arm.linux.org.uk
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
icside_register_v[56] is called from (__devinit) icside_probe
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
