* git://git.infradead.org/mtd-2.6: (58 commits)
mtd: jedec_probe: add PSD4256G6V id
mtd: OneNand support for Nomadik 8815 SoC (on NHK8815 board)
mtd: nand: driver for Nomadik 8815 SoC (on NHK8815 board)
m25p80: Add Spansion S25FL129P serial flashes
jffs2: Use SLAB_HWCACHE_ALIGN for jffs2_raw_{dirent,inode} slabs
mtd: sh_flctl: register sh_flctl using platform_driver_probe()
mtd: nand: txx9ndfmc: transfer 512 byte at a time if possible
mtd: nand: fix tmio_nand ecc correction
mtd: nand: add __nand_correct_data helper function
mtd: cfi_cmdset_0002: add 0xFF intolerance for M29W128G
mtd: inftl: fix fold chain block number
mtd: jedec: fix compilation problem with I28F640C3B definition
mtd: nand: fix ECC Correction bug for SMC ordering for NDFC driver
mtd: ofpart: Check availability of reg property instead of name property
driver/Makefile: Initialize "mtd" and "spi" before "net"
mtd: omap: adding DMA mode support in nand prefetch/post-write
mtd: omap: add support for nand prefetch-read and post-write
mtd: add nand support for w90p910 (v2)
mtd: maps: add mtd-ram support to physmap_of
mtd: pxa3xx_nand: add single-bit error corrections reporting
...
Trivial patch which adds the __init and __exit macros to the module_init /
module_exit functions to the following modules from drivers/mtd/
devices/m25p80.c
devices/slram.c
linux version 2.6.30
ftl.c
nand/cafe_nand.c
nand/cmx270_nand.c
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds a new "page" parameter to all NAND read_page/read_page_raw
APIs. The read_page API for the new mode ECC_HW_OOB_FIRST requires the
page information to send the READOOB command and read the OOB area before
the data area.
Reviewed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
[dwmw2: updated and made to still register whole device first]
Signed-off-by: Philip Rakity <pakity@yahoo.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Originally from Marcelo; modified to put the original timing registers
back instead of 0xFFFFFFFF.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
It was only the very early prototypes which made the mistake of using
the same device ident for all three functions on the device -- don't
bother trying to express that in the PCI match table, since the tools
don't cope. We can check in the probe routine instead, just in case.
Also remember to terminate the table.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The CAFÉ can handle two chip on separate chipselect lines. Hook up the
undocumented chipselect bits in the driver and probe both.
In the case of OLPC, it's not actually two separate devices -- it's a
single '1GiB' package with two 512MiB dies internally. So clear the
NAND_BBT_PERCHIP flag to treat it as a single chip for BBT purposes, and
make life easier for the firmware.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
