Skip compiling OMAP15xx I2C ISR for non-OMAP15xx builds. Saves 400 bytes
of text for most OMAP builds.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on an earlier patch from Nishant Menon:
- Transfers can use FIFO on FIFO capable devices
- Prevents errors for HSI2C if FIFO is not used
- Implemented errenous handling of STT-STP handling on SDP2430
Also merged in is a fix from Jaron Marini to fix occasional i2c
hang if OMAP_I2C_CON_STT remains asserted.
Signed-off-by: Jason P Marini <jason.marini@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Omap2430 has additional support for high-speed I2C.
This patch moves I2C speed parameter (from module) to platform data.
Also added basic High Speed support based on I2C bus speed.
This patch is tested for high speed I2C (with TWL4030 Keypad) and works as
expected.
Also change the 2430 i2chs_fck names to use the standard naming.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap_i2c_idle() sets an internal flag, "dev->idle", instructing its
ISR to decline interrupts. It sets this flag before it actually masks
the interrupts on the I2C controller. This is problematic, since an
I2C interrupt could arrive after dev->idle is set, but before the
interrupt source is masked. When this happens, Linux disables the I2C
controller's IRQ, causing all future transactions on the bus to fail.
Symptoms, happening on about 7% of boots:
irq 56: nobody cared (try booting with the "irqpoll" option)
<warning traceback here>
Disabling IRQ #56
i2c_omap i2c_omap.1: controller timed out
In omap_i2c_idle(), this patch sets dev->idle only after the interrupt
mask write to the I2C controller has left the ARM write buffer.
That's probably the major offender. For additional prophylaxis, in
omap_i2c_unidle(), the patch clears the dev->idle flag before
interrupts are enabled, rather than afterwards.
The patch has survived twenty-two reboots on the 3430SDP here without
wedging I2C1. Not absolutely dispositive, but promising!
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If there is a signal pending and wait_for_completion_interruptible_timeout
terminates with -ERESTARTSYS, we return and disable the i2c clocks in
omap_i2c_xfer.
If we terminate before sending last i2c message with a stop condition, the
bus remains busy and we are not able to send new messages into bus with
successive omap_i2c_xfer calls. Therefore a pending signal is not caught
here and we return only because of timeout or i2c error.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In commit e6bafba5b4, a bug was fixed that
involved converting !x & y to !(x & y). The code below shows the same
pattern, and thus should perhaps be fixed in the same way. In particular,
the result of !readl(i2c->regs + S3C2410_IICCON) & S3C2410_IICCON_IRQEN is
always 0.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@ expression E; constant C; @@
(
!E & !C
|
- !E & C
+ !(E & C)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The scx200_i2c driver is missing the .class parameter, which means no
i2c drivers are willing to probe for devices on the bus and attach to
them.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Add info->archdata field
i2c: Inform about deprecated chips directory
i2c: Use pci_ioremap_bar()
Schedule removal of the legacy i2c device driver binding model
i2c: Clean up <linux/i2c.h>
i2c: Update and clean up writing-clients document
i2c: Drop 2-byte address block transfer defines
i2c: Delete legacy model documentation
i2c: Constify i2c_get_clientdata's parameter
i2c: Delete outdated client porting guide
i2c: Make clear what the class field of i2c_adapter is good for
i2c-algo-pcf: Fix typo in debugging log message
i2c-algo-pcf: Add adapter hooks around xfer begin and end
i2c-algo-pcf: Pass adapter data into ->waitforpin() method
i2c-i801: Add support for Intel Ibex Peak
If present the info->archdata is copied into the dev->archdata.
Some (OpenFirmware) platforms need it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The chips directory under drivers/i2c is deprecated. Spread the word!
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use the newly introduced pci_ioremap_bar() function in drivers/i2c.
pci_ioremap_bar() just takes a pci device and a bar number, with the goal
of making it really hard to get wrong, while also having a central place
to stick sanity checks.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix typo in debugging log message.
deteted --> detected
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Some I2C bus implementations need to synchronize with external
entities, such as system firmware, which might also be programming the
same I2C bus.
In order to facilitate this add ->xfer_begin() and ->xfer_end() hooks
which are invoked around pcf_xfer().
[JD: Make these hooks optional.]
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Similar to commit 618b26d528, also remove
automatic probing for this i2c controller. Might need updates to dts files
using it.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Only accept dynids whose driver_data value matches one of the driver's
pci_driver_id entries. This prevents the user from accidentally passing
values the drivers do not expect.
Cc: Milton Miller <miltonm@bga.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The driver flag dynids.use_driver_data is almost consistently not set,
and causes more problems than it solves. It was initially intended as a
flag to indicate whether a driver's usage of driver_data had been
carefully inspected and was ready for values from userspace. That audit
was never done, so most drivers just get a 0 for driver_data when new
IDs are added from userspace via sysfs. So remove the flag, allowing
drivers to see the data directly (a followon patch validates the passed
driver_data value against what the drivers expect).
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tejun's commit 7b595756ec made sysfs
attribute->owner unnecessary. But the field was left in the structure to
ease the merge. It's been over a year since that change and it is now
time to start killing attribute->owner along with its users - one arch at
a time!
This patch is attempt #1 to get rid of attribute->owner only for
CONFIG_X86_64 or CONFIG_X86_32 . We will deal with other arches later on
as and when possible - avr32 will be the next since that is something I
can test. Compile (make allyesconfig / make allmodconfig / custom config)
and boot tested.
akpm: the idea is that we put the declaration of sttribute.owner inside
`#ifndef CONFIG_X86'. But that proved to be too ambitious for now because
new usages kept on turning up in subsystem trees.
[akpm: remove the ifdef for now]
Signed-off-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change i2c to use the new bcd2bin/bin2bcd functions instead of the
obsolete BCD2BIN/BIN2BCD macros.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The legacy i2c binding model is phasing out, so the ams driver needs
to be converted to a new-style i2c driver. Here is a naive approach of
this conversion. Basically it is moving the i2c device creation from
the ams driver to the i2c-powermac driver. This should work, but I
suspect we could come up with something cleaner by declaring the i2c
device as part of the platform setup. This could be done later by
someone more familiar with openfirmware-based platforms than I am
myself.
One nice thing brought by this conversion is that the ams driver
should be loaded automatically on systems where is is needed (at
least when the I2C interface to the chip is used) providing
coldplug-aware user-space environment.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Stelian Pop <stelian@popies.net>
Cc: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (46 commits)
UIO: Fix mapping of logical and virtual memory
UIO: add automata sercos3 pci card support
UIO: Change driver name of uio_pdrv
UIO: Add alignment warnings for uio-mem
Driver core: add bus_sort_breadthfirst() function
NET: convert the phy_device file to use bus_find_device_by_name
kobject: Cleanup kobject_rename and !CONFIG_SYSFS
kobject: Fix kobject_rename and !CONFIG_SYSFS
sysfs: Make dir and name args to sysfs_notify() const
platform: add new device registration helper
sysfs: use ilookup5() instead of ilookup5_nowait()
PNP: create device attributes via default device attributes
Driver core: make bus_find_device_by_name() more robust
usb: turn dev_warn+WARN_ON combos into dev_WARN
debug: use dev_WARN() rather than WARN_ON() in device_pm_add()
debug: Introduce a dev_WARN() function
sysfs: fix deadlock
device model: Do a quickcheck for driver binding before doing an expensive check
Driver core: Fix cleanup in device_create_vargs().
Driver core: Clarify device cleanup.
...
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (158 commits)
powerpc: Fix CHRP PCI config access for indirect_pci
powerpc/chrp: Fix detection of Python PCI host bridge on IBM CHRPs
powerpc: Fix 32-bit SMP boot on CHRP
powerpc: Fix link errors on 32-bit machines using legacy DMA
powerpc/pci: Improve detection of unassigned bridge resources
hvc_console: Fix free_irq in spinlocked section
powerpc: Get USE_STRICT_MM_TYPECHECKS working again
powerpc: Reflect the used arguments in machine_init() prototype
powerpc: Fix DMA offset for non-coherent DMA
powerpc: fix fsl_upm nand driver modular build
powerpc/83xx: add NAND support for the MPC8360E-RDK boards
powerpc: FPGA support for GE Fanuc SBC610
i2c: MPC8349E-mITX Power Management and GPIO expander driver
powerpc: reserve two DMA channels for audio in MPC8610 HPCD device tree
powerpc: document the "fsl,ssi-dma-channel" compatible property
powerpc: disable CHRP and PMAC support in various defconfigs
OF: add fsl,mcu-mpc8349emitx to the exception list
powerpc/83xx: add DS1374 RTC support for the MPC837xE-MDS boards
powerpc: remove support for bootmem-allocated memory for the DIU driver
powerpc: remove non-dependent load fsl_booke PTE_64BIT
...
Add support for SMBus Process Call transactions. These are combined
word write, word read transactions.
Signed-off-by: Prakash Mortha <pmortha@escient.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Restore the i2c_smbus_process_call() as one driver (for the
Micronas MAP5401) will need it soon.
[JD: Update documentation accordingly.]
Signed-off-by: Prakash Mortha <pmortha@escient.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move I2C driver model init earlier in the boot sequence.
This avoids oopsing in statically linked systems when some
subsystems register I2C drivers in subsys_initcall() code,
but those subsystems are linked (and initialized) before I2C.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The two Tyan SMBus mux drivers (i2c-amd756-s4882 and i2c-nforce2-s4985)
are only useful on specific x86 motherboards, so there is no point in
letting them be built on other architectures.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Guard I2C against oopsing because of init sequence problems, by
verifying that i2c_init() has been called before calling any
routines that rely on that initialization. This specific test
just requires that bus_register(&i2c_bus_type) was called.
Examples of this kind of oopsing come from subystems and drivers
which register I2C drivers in their subsys_initcall code but
which are statically linked before I2C by drivers/Makefile.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The i2c-parport-light driver isn't a real platform driver, so it
should not instantiate platform devices with resources. The resource
management system can't cope with colliding resources, and we are
likely to create such a colliding resource.
So, better just try to grab the I/O ports we need right at module
initialization time, and bail out if we can't. It has the added
benefit that the module will no longer load if it isn't going to work,
which is definitely more user-friendly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
All the tps6501{0,1,2,3,4} chips have a signal for hooking up with
a vibrator (for non-auditory cell phone "ring") ... expose that as
one more (output-only) GPIO.
[ dbrownell@users.sourceforge.net: comments; list tps65014 too ]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Thanks to new datasheets published on http://linux.via.com.tw we can now add
support for VX800/VX820 chipsets.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This adds support for the SMBus adapter found in the various FPGAs on
the Renesas Highlander platforms. Particularly the R0P7780LC0011RL and
R0P7785LC0011RL FPGAs.
Functionality is fairly restricted, in that only byte and block data
transfers are supported. Normal/fast mode and IRQ/polling are also
supported. Primarily used for various RTCs and thermal sensors.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Grabbing ISA bus resources without anything or anyone telling us we
should can break boot on randconfig/allyesconfig builds by keeping
resources that are in fact owned by different hardware busy and does
as reported by Ingo Molnar.
Generally it's also dangerous to just poke at random I/O ports and
especially those in the range where other old easily confused ISA
hardware might live.
For this specialized I2C bus driver, insist that the user specifies
the resources before grabbing them.
The^WA user of this driver is a one time
echo "options i2c-pca-isa base=0x330 irq=10" >> /etc/modprobe.conf
away from the old behaviour.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Based on David Brownell's patch for tps65010 and previous work by
Felipe Balbi, this patch finishes converting isp1301_omap to a
new-style i2c driver.
There's definitely room for further drivers cleanups, but these are
out of the scope of this patch.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Based on David Brownell's patch for tps65010, this patch
starts converting isp1301_omap.c to new-style i2c driver.
Signed-off-by: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Tony Lindgren <tony@atomide.com>
On MPC8349E-mITX, MPC8315E-RDB and MPC837x-RDB boards there is a
Freescale MC9S08QG8 (MCU) chip with the custom firmware
pre-programmed. The chip is used to power-off the board by the
software, and to control some GPIO pins.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (236 commits)
[ARM] 5300/1: fixup spitz reset during boot
[ARM] 5295/1: make ZONE_DMA optional
[ARM] 5239/1: Palm Zire 72 power management support
[ARM] 5298/1: Drop desc_handle_irq()
[ARM] 5297/1: [KS8695] Fix two compile-time warnings
[ARM] 5296/1: [KS8695] Replace macro's with trailing underscores.
[ARM] pxa: allow multi-machine PCMCIA builds
[ARM] pxa: add preliminary CPUFREQ support for PXA3xx
[ARM] pxa: add missing ACCR bit definitions to pxa3xx-regs.h
[ARM] pxa: rename cpu-pxa.c to cpufreq-pxa2xx.c
[ARM] pxa/zylonite: add support for USB OHCI
[ARM] ohci-pxa27x: use ioremap() and offset for register access
[ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()
[ARM] ohci-pxa27x: use platform_get_{irq,resource} for the resource
[ARM] ohci-pxa27x: move OHCI controller specific registers into the driver
[ARM] ohci-pxa27x: introduce flags to avoid direct access to OHCI registers
[ARM] pxa: move I2S register and bit definitions into pxa2xx-i2s.c
[ARM] pxa: simplify DMA register definitions
[ARM] pxa: make additional DCSR bits valid for PXA3xx
[ARM] pxa: move i2c register and bit definitions into i2c-pxa.c
...
Fixed up conflicts in
arch/arm/mach-versatile/core.c
sound/soc/pxa/pxa2xx-ac97.c
sound/soc/pxa/pxa2xx-i2s.c
manually.
This patch suppresses I2C device probing by clearing the class field
of the "struct i2c_adapter" for the MPC I2C bus adapters. Some board
configurations which rely on probing must be fixed up by adding a
proper I2C device node to the DTS file, like the TQM85xx modules.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add fast_mode option to i2c_pxa_platform_data and use it to set the
ICR_FM bit appropriately when i2c_pxa_reset is called. Parameter
called fast_mode rather than frequency as this driver is also used
for the i2c_pxa_pwr bus which has different normal and fast frequencies.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We need to convert the error pointer from class_create(), else we'll return the
successful return code from register_chrdev() on failure.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
__devexit for i2c_powermac_probe is obviously wrong. In the definition
of struct platform_driver i2c_powermac_driver the remove function
i2c_powermac_remove is wrapped in __devexit_p, so it should be defined
using __devexit.
Signed-off-by: Uwe Kleine-Koenig <ukleinek@informatik.uni-freiburg.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Now that arch/ppc is dead CONFIG_PPC_MERGE is always defined for all
powerpc platforms and we want to get rid of CONFIG_PPC_MERGE use
CONFIG_PPC instead.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Properly hook the I2C driver into the PM code; the previous fix for
this (ece5f7b3c4) worked around the
platform where I2C is required to be available early during resume.
It has been found to be sufficient to use the early resume hook for
this function, so the original hack can die. Leave the hack in
place for the PIO transfer handler though.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
i2c_pxa_abort can be called from the atomic context.
Change it to use mdelay and counted loop.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add power I2C support for PXA3xx processors
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch teaches the i2c-sh_mobile driver to make use of wait irqs.
Without this patch only dte irqs are used which may lead to overruns
and cases of missing stop and extra bytes being read on the i2c bus.
Use of wait irqs forces the hardware to pause and wait until the cpu
is ready. Polling is also reworked in this patch to fix ms delay issues.
Verified with bus analyzer and tested on MigoR and AP325RXA boards.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some DVB adapters do not support the special I2C transaction that we
use for probing purposes. There's no point in logging this event, as
there's nothing the user can do and in general there is no actual
problem. So, degrade one of these messages to a debug message, and
move the other one around so that it is only printed on bogus drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Uwe Bugla <uwe.bugla@gmx.de>
device_init_wakeup must be called after device_register.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix various printk format strings where %zd was passed a size_t;
those should be %zu instead. (Courtesy of a version of GCC which
warns when these details are wrong.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We check for address business in i2c_probe_address(),
i2c_detect_address() and i2c_new_probed_device(), but this isn't
sufficient. Drivers can call i2c_attach_client() and
i2c_new_device() on any address, so we must check the address there
as well.
This fixes bug #11239:
http://bugzilla.kernel.org/show_bug.cgi?id=11239
Signed-off-by: Jean Delvare <khali@linux-fr.org>
In kernel 2.6.26, the ability to select I2C algorithm drivers manually
was removed, as all in-kernel drivers do that automatically. However
there were some complaints that it was a problem for out-of-tree I2C
bus drivers. In order to address these complaints, let's allow manual
selection of these drivers again, but still hide them by default for
better general user experience.
This closes bug #11140:
http://bugzilla.kernel.org/show_bug.cgi?id=11140
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix a NULL pointer dereference that happened when calling
i2c_new_probed_device on one of the addresses for which we use byte
reads instead of quick write for detection purpose (that is: 0x30-0x37
and 0x50-0x5f).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The two I2C bus multiplexer drivers (i2c-amd756-s4882 and
i2c-nforce2-s4985) make use of the bus they want to multiplex before
checking if it is really present. Swap the instructions to test for
presence first. This fixes a oops reported by Ingo Molnar.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ingo Molnar <mingo@elte.hu>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are 43 includes of asm/mach-types.h by files that don't
reference anything from that file. Remove these unnecessary
includes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PM_SUSPEND_MEM: Blackfin does not maintain register state through
Hibernate. Save and restore peripheral base initialization during
PM transitions.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Change the i2c_gpio driver to use platform_driver_register()
instead of platform_driver_probe() to ensure that is can
attach to any devices that may be loaded after it has initialised.
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Allow the platform data to specify the bus bumber that the
new I2C bus will be given. This is to allow the use of the
board registration mechanism to specify the new style of
I2C device registration which allows boards to provide a
list of attached devices.
Note, as discussed on the mailing list, we have dropped
backwards compatibility of adding an dynamic bus number
as it should not affect most boards to have the bus pinned
to 0 if they have either not specified platform data for
driver. Any board supplying platform data will automatically
have the bus_num field set to 0, and anyone who needs the
driver on a different bus number can supply platform data
to set bus_num.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds functionality to the gpio-lib subsystem to make it
possible to enable the gpio-lib code even if the architecture code didn't
request to get it built in.
The archtitecture code does still need to implement the gpiolib accessor
functions in its asm/gpio.h file. This patch adds the implementations for
x86 and PPC.
With these changes it is possible to run generic GPIO expansion cards on
every architecture that implements the trivial wrapper functions. Support
for more architectures can easily be added.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a simple sysfs interface for GPIOs.
/sys/class/gpio
/export ... asks the kernel to export a GPIO to userspace
/unexport ... to return a GPIO to the kernel
/gpioN ... for each exported GPIO #N
/value ... always readable, writes fail for input GPIOs
/direction ... r/w as: in, out (default low); write high, low
/gpiochipN ... for each gpiochip; #N is its first GPIO
/base ... (r/o) same as N
/label ... (r/o) descriptive, not necessarily unique
/ngpio ... (r/o) number of GPIOs; numbered N .. N+(ngpio - 1)
GPIOs claimed by kernel code may be exported by its owner using a new
gpio_export() call, which should be most useful for driver debugging.
Such exports may optionally be done without a "direction" attribute.
Userspace may ask to take over a GPIO by writing to a sysfs control file,
helping to cope with incomplete board support or other "one-off"
requirements that don't merit full kernel support:
echo 23 > /sys/class/gpio/export
... will gpio_request(23, "sysfs") and gpio_export(23);
use /sys/class/gpio/gpio-23/direction to (re)configure it,
when that GPIO can be used as both input and output.
echo 23 > /sys/class/gpio/unexport
... will gpio_free(23), when it was exported as above
The extra D-space footprint is a few hundred bytes, except for the sysfs
resources associated with each exported GPIO. The additional I-space
footprint is about two thirds of the current size of gpiolib (!). Since
no /dev node creation is involved, no "udev" support is needed.
Related changes:
* This adds a device pointer to "struct gpio_chip". When GPIO
providers initialize that, sysfs gpio class devices become children of
that device instead of being "virtual" devices.
* The (few) gpio_chip providers which have such a device node have
been updated.
* Some gpio_chip drivers also needed to update their module "owner"
field ... for which missing kerneldoc was added.
* Some gpio_chips don't support input GPIOs. Those GPIOs are now
flagged appropriately when the chip is registered.
Based on previous patches, and discussion both on and off LKML.
A Documentation/ABI/testing/sysfs-gpio update is ready to submit once this
merges to mainline.
[akpm@linux-foundation.org: a few maintenance build fixes]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This mirrors the functionality that driver_for_each_device has as well.
We add a start variable, and all callers of the function are fixed up at
the same time.
The block layer will be using this new functionality in a follow-on
patch.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new-style max6875 driver implements the optional detect() callback
to cover the use cases of the legacy driver. I'm curious if anyone
really needs this though, so it might be removed in the feature.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style pca9539 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Warning: users will now have to use the force module parameter to get
the driver to attach to their device. That's not a bad thing as these
devices can't be detected anyway.
Note that this doesn't change the fact that this driver is deprecated
in favor of gpio/pca953x.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style pcf8575 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Warning: users will now have to use the force module parameter to get
the driver to attach to their device. That's not a bad thing as these
devices can't be detected anyway.
Note that this doesn't change the fact that this driver is deprecated
in favor of gpio/pcf857x.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style pcf8574 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Warning: users will now have to use the force module parameter to get
the driver to attach to their device. That's not a bad thing as these
devices can't be detected anyway.
Note that this doesn't change the fact that this driver is deprecated
in favor of gpio/pcf857x.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style pcf8591 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style eeprom driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Clear i2c_adapter.dev on adapter removal. This makes it possible to
re-add the adapter at a later point, which some drivers
(i2c-amd756-s4882, i2c-nforce2-s4985) actually do.
This fixes a bug reported by John Stultz here:
http://lkml.org/lkml/2008/7/15/720
and by Ingo Molar there:
http://lkml.org/lkml/2008/7/16/78
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: (56 commits)
i2c: Add detection capability to new-style drivers
i2c: Call client_unregister for new-style devices too
i2c: Clean up old chip drivers
i2c-ibm_iic: Register child nodes
i2c: New-style EEPROM driver using device IDs
i2c: Export the i2c_bus_type symbol
i2c-au1550: Fix PM support
i2c-dev: Delete empty detach_client callback
i2c: Drop stray references to lm_sensors
i2c: Check for ACPI resource conflicts
i2c-ocores: basic PM support
i2c-sibyte: SWARM I2C board initialization
i2c-i801: Fix handling of error conditions
i2c-i801: Rename local variable temp to status
i2c-i801: Properly report bus arbitration loss
i2c-i801: Remove verbose debugging messages
i2c-algo-pcf: Drop unused struct members
i2c-algo-pcf: Multi-master lost-arbitration improvement
i2c: Deprecate the legacy gpio drivers
i2c-pxa: Initialize early
...
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (241 commits)
[ARM] 5171/1: ep93xx: fix compilation of modules using clocks
[ARM] 5133/2: at91sam9g20 defconfig file
[ARM] 5130/4: Support for the at91sam9g20
[ARM] 5160/1: IOP3XX: gpio/gpiolib support
[ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.
[ARM] 5084/1: zylonite: Register AC97 device
[ARM] 5085/2: PXA: Move AC97 over to the new central device declaration model
[ARM] 5120/1: pxa: correct platform driver names for PXA25x and PXA27x UDC drivers
[ARM] 5147/1: pxaficp_ir: drop pxa_gpio_mode calls, as pin setting
[ARM] 5145/1: PXA2xx: provide api to control IrDA pins state
[ARM] 5144/1: pxaficp_ir: cleanup includes
[ARM] pxa: remove pxa_set_cken()
[ARM] pxa: allow clk aliases
[ARM] Feroceon: don't disable BPU on boot
[ARM] Orion: LED support for HP mv2120
[ARM] Orion: add RD88F5181L-FXO support
[ARM] Orion: add RD88F5181L-GE support
[ARM] Orion: add Netgear WNR854T support
[ARM] s3c2410_defconfig: update for current build
[ARM] Acer n30: Minor style and indentation fixes.
...
This includes PXA work up to the SPI changes for the initial merge,
since e172274ccc depends on the SPI
tree being merged.
Conflicts:
arch/arm/configs/em_x270_defconfig
arch/arm/configs/xm_x270_defconfig
Add a mechanism to let new-style i2c drivers optionally autodetect
devices they would support on selected buses and ask i2c-core to
instantiate them. This is a replacement for legacy i2c drivers, much
cleaner.
Where drivers had to implement both a legacy i2c_driver and a
new-style i2c_driver so far, this mechanism makes it possible to get
rid of the legacy i2c_driver and implement both enumerated and
detected device support with just one (new-style) i2c_driver.
Here is a quick conversion guide for these drivers, step by step:
* Delete the legacy driver definition, registration and removal.
Delete the attach_adapter and detach_client methods of the legacy
driver.
* Change the prototype of the legacy detect function from
static int foo_detect(struct i2c_adapter *adapter, int address, int kind);
to
static int foo_detect(struct i2c_client *client, int kind,
struct i2c_board_info *info);
* Set the new-style driver detect callback to this new function, and
set its address_data to &addr_data (addr_data is generally provided
by I2C_CLIENT_INSMOD.)
* Add the appropriate class to the new-style driver. This is
typically the class the legacy attach_adapter method was checking
for. Class checking is now mandatory (done by i2c-core.) See
<linux/i2c.h> for the list of available classes.
* Remove the i2c_client allocation and freeing from the detect
function. A pre-allocated client is now handed to you by i2c-core,
and is freed automatically.
* Make the detect function fill the type field of the i2c_board_info
structure it was passed as a parameter, and return 0, on success. If
the detection fails, return -ENODEV.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We call adapter->client_register for both legacy and new-style i2c
devices, however we only call adapter->client_unregister for legacy
drivers. This doesn't make much sense. Usually, drivers will undo
in client_unregister what they did in client_register, so we should
call neither or both for every given i2c device.
In order to ease the transition from legacy to new-style devices, it
seems preferable to actually call both.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Clean up old i2c chip drivers:
* Name the i2c_client "client" instead of "new_client".
* Drop useless initializations to 0.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch completes the conversion of the IBM IIC driver to an
of-platform driver.
It removes the index from the IBM IIC driver and makes it an unnumbered
driver. It then calls of_register_i2c_devices to properly register all
the child nodes in the DTS.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add a new-style driver for most I2C EEPROMs, giving sysfs read/write
access to their data. Tested with various chips and clock rates.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Export the root of the i2c bus so that PowerPC device tree code can
iterate over devices on the i2c bus.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix driver power management:
- suspend the PSC while driver is idle.
- move PSC init/deinit to separate functions, as PSC must be
initialized/shutdown on resume/suspend.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Implementing detach_client is optional, so there is no point in
an empty implementation.
Likewise, i2c driver IDs are optional, and we don't need one.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Check for ACPI resource conflicts in i2c bus drivers. I've included
all recent SMBus master drivers for PC hardware.
I've voluntarily left out:
* Drivers that don't run on PCs: they can't conflict with ACPI.
* Bit-banged bus device drivers: it's very unlikely that ACPI would
deal with such buses.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Basic PM support: reinit the core on resume, disable it on suspend.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The standard rtc-m41t80.c driver cannot be used with the SWARM as it is,
because the board does not provide setup information for the I2C core.
As a result the bus and the address to probe for the M41T80 chip is not
known.
Here is a set of changes that fix the problem:
1. swarm-i2c.c -- SWARM I2C board setup, currently for the M41T80 chip on
the bus #1 only (there is a MAX6654 temperature sensor on the bus #0
which may be added in the future if we have a driver for that chip).
2. The i2c-sibyte.c BCM1250A SMBus controller driver now registers its
buses as numbered so that board setup is correctly applied.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move the check of pre-transaction and post-transaction conditions to
separate functions, and adjust them a bit. Having dedicated functions
for that ensures that errors are handled in a consistent way.
Bit HOST_BUSY of the status register is read-only, so writing to it is
certainly not going to clear it. If this bit is set then we simply
don't want to start the transaction, as it means that somebody else
(ACPI, SMM?) is already using the controller.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Bit BUS_ERR of the status register means that the ICH host controller
lost the arbitration. Report this event as such.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Dumping the register values before and after every transaction was
useful during driver development but now it's only spamming the log.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Struct members udelay and timeout aren't used anywhere, so drop them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Eric Brower <ebrower@gmail.com>
Improve lost-arbitration handling of PCF8584. This is necessary for
support of a currently out-of-kernel driver for Sun Microsystems E250
environmental management; perhaps others.
Signed-off-by: Eric Brower <ebrower@gmail.com>
Acked-by: Dan Smolik <marvin@mydatex.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The legacy pcf8574 and pcf8575 drivers should be avoided
on systems using the new gpiolib code, and generally deprecated
in the same way the legacy pca9539 driver is deprecated.
Also, correct the pca9539 deprecation to match the current name
of the preferred driver: pca953x, supporting several more chips.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Initialize the pxa i2c bus during subsystem initialization to make it
available during driver initialization (e.g. display powerup for pxafb).
Signed-off-by: Uli Luckas <u.luckas@road.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Enable the IBM I2C driver for all PPC4xx variants by adding
"ibm,iic" to the compatible list. This way all currently available
arch/powerpc 4xx ports can make use of this driver without any changes.
Additionally all "other" compatible entries are removed since they are
not needed anymore.
Currently all 4xx PPC's have the same compatible I2C macro. If at some
time an incompatibility is detected we can take care of this with an
additional property.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The deprecated OCP style driver part is used by the "old" arch/ppc
platform. This platform is scheduled for removal in June/July this year.
This patch now removes the OCP driver part from the IBM I2C driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When I2C block reads are not supported by the underlying adapter, use
SMBus read word transactions instead of consecutive byte reads.
Reasons for this change are:
* The consecutive byte read approach is not safe on multi-master buses.
* While consecutive byte reads have less overhead if you only count the
bytes on the bus, it takes more than twice as many transactions as
with SMBus read word transactions, and each transaction has a cost:
taking and releasing the adapter mutex, and for polling drivers,
waiting for the transaction to complete.
This change yields a significant performance boost at HZ=250 with
EEPROMs on an Intel 82801 bus (basically twice as fast.)
SMBus read word transactions are widely supported so I don't expect
compatibility issues.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Let general purpose I2C/SMBus bus drivers add SPD to their class. Once
this is done, we will be able to tell the eeprom driver to only probe
for SPD EEPROMs and similar on these buses.
Note that I took a conservative approach here, adding I2C_CLASS_SPD to
many drivers that have no idea whether they can host SPD EEPROMs or not.
This is to make sure that the eeprom driver doesn't stop probing buses
where SPD EEPROMs or equivalent live.
So, bus driver maintainers and users should feel free to remove the SPD
class from drivers those buses never have SPD EEPROMs or they don't
want the eeprom driver to bind to them. Likewise, feel free to add the
SPD class to any bus driver I might have missed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Bugfixes to the i2c-cpm driver
- enable correct interrupts (I2CER_TXE instead of I2CER_BUSY)
- replace forgotten iic with i2c
- prefix debug-output on init with 0x and add frequency
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This driver uses the port of 2.4 code from Vitaly Bordug
<vitb@kernel.crashing.org> and the actual algorithm used by the i2c
driver of the DBox code on cvs.tuxboc.org from Felix Domke
(tmbinc@gmx.net) and Gillem (htoa@gmx.net) converted to an
of_platform_driver. Tested on CPM1 (MPC823 on dbox2 hardware) and
CPM2 (MPC8272).
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is part of the effort to get rid of the BKL.
[JD: In fact i2c-dev doesn't need more locking than is already done
for the other i2c drivers, so we can simply switch to unlocked_ioctl.]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
New i2c bus driver for the Intel SCH chipsets (AF82US15W, AF82US15L,
AF82UL11L).
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use list_for_each_entry_safe() in i2c_del_adapter() and i2c_del_driver().
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix errorcode to be more descriptive when ioremap fails.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Give a more concrete error code, when the bus is not idle.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Many PC SMBus host controller drivers don't properly handle the case
where they are requested to achieve a transaction they do not support.
Update them so that the consistently print a warning message and
return a single error value in this case.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The i2c-piix4 driver was used recently as a model to write a new SMBus
host controller driver and this made me realize that the code of this
old driver wasn't exactly good. So, here are many cleanups and minor
fixes to this driver, so that these minor mistakes aren't duplicated
again:
* Delete unused structure.
* Delete needless forward function declaration.
* Properly announce the SMBus host controller as we find it.
* Spell it SMBus not SMB.
* Return -EBUSY instead of -ENODEV when the I/O region is already in
use.
* Drop useless masks on the 7-bit address and the R/W bit.
* Reject block transaction requests with an invalid block length.
* Check and report block transaction replies with an invalid block
length.
* Delete a useless comment.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tighten error paths used by various i2c adapters (mostly x86) so
they return real fault/errno codes instead of a "-1" (which is
most often interpreted as "-EPERM"). Build tested, with eyeball
review.
One minor initial goal is to have adapters consistently return
the code "-ENXIO" when addressing a device doesn't get an ACK
response, at least in the probe paths where they are already
good at stifling related logspam.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Defend the i2c refcount calls against NULL pointers, as is important
(and conventional) for such calls. Note that none of the current
callers of i2c_use_client() use its return value.
[JD: I hate this but apparently all the other subsystems do it so...]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Provide kerneldoc for most of the I2C and SMBus I/O calls. Add a
comment summarizing some fault reporting issues which affect the
ability to provide clean fault reports through I2C master transfer
calls. (Making it hard to precisely specify their return values...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Function i2c_smbus_write_quick has no users left, so we can delete it.
Also update the list of these helper functions which are gone but
could be added back if needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The list of I2C/SMBus bus drivers is growing and it is sometimes
difficult for the users to figure out what drivers they should enable.
By grouping the drivers by type, I hope to make the selection easier.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
More updates to the I2C stack's fault reporting: make the core stop
returning "-1" (usually "-EPERM") for all faults. Instead, pass lower
level fault code up the stack, or return some appropriate errno.
This patch happens to touch almost exclusively SMBus calls.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Since only a few Blackfins lack TWI, just list them in a depends
statement.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch contains the scheduled removal of i2c-i810, i2c-prosavage
and i2c-savage4.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Just like the Tyan S4882, the S4985 uses a multiplexer to give access
to all 16 memory module SPD EEPROMs. This specific i2c-nforce2-s4985
driver adds support for this. It is heavily based on the older
i2c-amd756-s4882 driver.
As more mainboards will use multiplexer chips, we will have to find a
way to support them without having to write a new specfic driver for
each. The recent changes to the i2c subsystem should help us, and the
new gpio subsystem might help, too.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
If an interrupt happens before an I2c master read/write,
complete is called on uninitialized structure.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
If wait_for_completion_interruptible_timeout exits due
to a signal, the i2c bus was locking up.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Interrupts are enabled at the point where the DAVINCI_I2C_IVR_REG is read,
so unless an interrupt happened just at that moment, no interrupt would be
pending. Even though documentation implies you should do this, I see no
reason. If slave support is added, this read would cause a hard to
reproduce bug.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Previously the dev_dbg only printed if no error.
Printing also on an error is more useful
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Ensure psc value gives a clock between 7-12 MHz
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Convert i2c-mpc to an of_platform driver. Utilize the code in
drivers/of-i2c.c to make i2c modules dynamically loadable by the
device tree.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Both i2c-pxa.c and irq.c still include pxa2xx-gpio.h although is is not
needed anymore.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change omap USB code to use omap_read/write instead of __REG for multi-omap
Cc: David Brownell <david-b@pacbell.net>
Cc: linux-usb@vger.kernel.org
Cc: i2c@lm-sensors.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a MODULE_ALIAS() statement for the i2c-s3c2410 controller
to ensure that it can be autoloaded on the S3C2440 systems that
we support.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The driver should be returning -ENXIO for transfers that do not
pass the initial address byte stage.
Note, also small tidyups to the driver comments in the area.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We should check for the reception of an ACK after transmitting each
data byte. The address send has been correctly checking this, but the
data write byte state should have also been checking for these failures.
As part of the same fix, we remove the ACK checking from the receive
path where it should not have been checking for an ACK which our hardware
was sending.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This fixes a build error introduced when the power manager
register definitions were moved into pxa2xx-regs.h.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
i2c-core takes care of the possible corruption of 24RF08 chips for
quite some times, so device devices no longer need to do it. And they
really should not, as applying the prevention twice voids it.
I thought that I had fixed all drivers long ago but apparently I had
missed that one.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Gardner <bgardner@wabtec.com>
The i2c-amd756 driver pretends to support SMBus process call
transactions but actually does not. Fix it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Remove the old driver_name/type scheme for i2c driver matching. Only the
standard aliasing model will be used from now on.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
There is a strange chip at 0x2e on the second SMBus channel of the
DFI Lanparty NF4 Expert motherboard. Accessing the chip reboots the
system. As there's nothing interesting on this SMBus channel, the
easiest and safest thing to do is to disable it on that board.
This is a better fix to bug #5889 than the it87 driver update that was
done originally:
http://bugzilla.kernel.org/show_bug.cgi?id=5889
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The Alchemy platform code registers the SMBus device using the virtual
address of its registers instead of the physical one -- fix this, taking
into account that actually the whole megabyte is decoded by any of the
programmable serial controllers (one of which is SMBus), and that all the
Alchemy peripherals are directly mappable into KSEG1 kernel space and
therefore ioremap() call would just boil down to CKSEG1ADDR() invocation.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As the old driver_name/type matching scheme is going away soon, change
the dummy device mechanism to use the new matching scheme.
This has the downside that dummy i2c clients can no longer choose
their name, they'll all appear as "dummy" in sysfs and in log
messages. I don't think it is a problem in practice though, as there
is little reason to use these i2c clients to log messages.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The i2c_sibyte_add_bus() function is not called, nor meant to, from
outside, so mark it as static; fixing a sparse warning too.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The frequency may have been once hardcoded to 100 kHz, but currently it is
passed as an argument to i2c_sibyte_add_bus(), so update the comment to
match code. While at it, reformat a nearby comment for consistency. No
functional changes.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We had a report that running sensors-detect on a Sapphire AM2RD790
motherbord killed the CPU. While the exact cause is still unknown,
I'd rather play it safe and prevent any access to the SMBus on that
machine by not letting the i2c-piix4 driver attach to the SMBus host
device on that machine. Also blacklist a similar board made by DFI.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Per the PIIX4 errata, there maybe a delay between setting the
start bit in the Smbus Host Controller Register and the transaction
actually starting. If the driver doesn't delay long enough, it
may appear that the transaction is complete when actually it
hasn't started, this may lead to bus collisions.
While 1 ms appears to be enough for most chips, the ServerWorks CSB5
wants 2 ms.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Alter the mpc i2c driver to use the NO_IRQ symbol instead of the constant
zero when checking for valid interrupts. NO_IRQ=-1 on ppc and NO_IRQ=0 on
powerpc so the checks against zero are not correct.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Based on earlier work by Jon Smirl and Jochen Friedrich.
Update most new-style i2c drivers to use standard module aliasing
instead of the old driver_name/type driver matching scheme. I've
left the video drivers apart (except for SoC camera drivers) as
they're a bit more diffcult to deal with, they'll have their own
patch later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Jochen Friedrich <jochen@scram.de>
Based on earlier work by Jon Smirl and Jochen Friedrich.
This patch allows new-style i2c chip drivers to have alias names using
the official kernel aliasing system and MODULE_DEVICE_TABLE(). At this
point, the old i2c driver binding scheme (driver_name/type) is still
supported.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jochen Friedrich <jochen@scram.de>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
tps65010_remove() calls i2c_get_clientdata(client) but the client data
is never set during initialization, so it gets a NULL pointer at best.
I guess it was never spotted because the tps65010 driver is typically
not built modular so this function is discarded.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
* Remove a needless include.
* Remove a legacy comment in piix4_access.
* Minor optimization in piix4_access.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Since 43cc71eed1, the platform
modalias is prefixed with "platform:". Add MODULE_ALIAS() to the
hotpluggable I2C platform drivers, to allow module auto loading.
[ db: add some more drivers ]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is V5 of the SuperH Mobile I2C Controller Driver. A simple Master
only driver for the I2C block included in processors such as sh7343,
sh7722 and sh7723. Tested on a sh7722 MigoR using a rs5c732b rtc.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Simply use "depends on BLACKFIN" (which is technically correct) and just
document which machines have the device.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Blackfin TWI controller hardware pin should be requested from GPIO port controller
Before BF54x, there is no need to do this. But as long as BF54x and BF52x
are supported by this generic driver, the missing pin mux operation should be
added.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
- Dynamic alloc the resource of TWI driver data according to board information
- TWI register read/write accessor based on dynamic regs_base
- Support TWI0/TWI1 for BF54x
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
- Create a new mode TWI_I2C_MODE_REPEAT.
- No change to smbus operation.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
__FUNCTION__ is gcc-specific, use __func__.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Driver for I2C interfaces in master mode on SH7760.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Split the handling of the I2C_RDWR and I2C_SMBUS ioctls to their own
functions. This limits the stack usage, saves one level of indentation
and makes the code more readable.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch allows the i2c-ibm_iic driver to be built either as an ocp
driver or an of_platform driver. This allows it to run under the powerpc
arch but maintains backward compatibility with the ppc arch.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Change the log levels based on feedback from linxppc-dev.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The separation between algorithm and adapter was unsharp at places. This was
partly hidden by the fact, that the ISA-driver allowed just one instance and
had all private data in static variables. This patch makes neccessary
preparations to add a platform driver on top of the algorithm, while still
supporting ISA. Note: Due to lack of hardware, the ISA-driver could not be
tested except that it builds.
Concerning the core struct i2c_algo_pca_data:
- A private data field was added, all hardware dependant data may go here.
Similar to other algorithms, now a pointer to this data is passed to the
adapter's functions. In order to make as less changes as possible to the
ISA-driver, it leaves the private data empty and still only uses its static
variables.
- A "reset_chip" function pointer was added; such a functionality must come
from the adapter, not the algorithm.
- use a variable "i2c_clock" instead of a function pointer "get_clock",
allowing for write access to a default in case a wrong value was supplied.
In the algorithm-file:
- move "i2c-pca-algo.h" into "linux/i2c-algo-pca.h"
- now using per_instance timeout values (i2c_adap->timeout)
- error messages specify the device, not only the driver name
- restructure initialization to easily support "i2c_add_numbered_adapter"
- drop "retries" and "own" (i2c address) as they were unused
(The state-machine for I2C-communication was not touched.)
In the ISA-driver:
- adapt to new algorithm
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Remove trailing whitespaces to make further patches more readable. Also remove
an unnecessary UTF-char for simplicity ("us" for microseconds is fine enough).
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The algorithm drivers are helper drivers that are selected automatically
as needed. There's no point in listing them in the config menu, it can
only confuse users and waste their time.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
two reasons:
1. GPIO namings and their mode definitions are conceptually not part
of the PXA register definitions
2. this is actually a temporary move in the transition of PXA2xx to
use MFP-alike APIs (as what PXA3xx is now doing), so that legacy
code will still work and new code can be added in step by step
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make the tps65010 driver use gpiolib to expose its GPIOs.
Note: This patch will get merged via omap tree instead of I2C
as it will cause some board updates. This has been discussed
at on the I2C list:
http://lists.lm-sensors.org/pipermail/i2c/2008-March/003031.html
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: i2c@lm-sensors.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
I have recently bought some USB PIDs from EZPrototypes for my USB projects
and one will be for the i2c-tiny-usb. I have not yet started to use the new
one in the official i2c-tiny-usb firmware since i think it makes sense to get
the change into the kernel before releasing a modified firmware.
This patch adds support for the EZPrototypes USB vid/pid pair used in later
i2c-tiny-usb firmware versions (avrusb v1.06 and up, usbtiny v2.06 and up).
Signed-off-by: Till Harbaum <Till@Harbaum.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
DAVINCI_I2C_STR_REG is a write 1 to clear register,
so don't use a read/modify/write cycle.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Noticed this when grepping for fast mode module params, the i2c-ibm_iic
driver was using a non-existent variable for MODULE_PARM_DESC. Fix it up
to reflect what it's actually supposed to be describing.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Sometimes kernel-doc and xmlto conspire to create output that is invalid
and causes problems. Until I know a real/better solution, change the
source code that causes this.
If anyone has better fixes or can just explain what is happening here,
that would be great.
xmlto: input does not validate (status 1)
mmotm-2008-0314-1449/Documentation/DocBook/kernel-api.xml:71468: parser error : Opening and ending tag mismatch: programlisting line 71464 and para
</para><para>
^
mmotm-2008-0314-1449/Documentation/DocBook/kernel-api.xml:71480: parser error : Opening and ending tag mismatch: para line 71473 and programlisting
</programlisting></informalexample>
^
make[1]: *** [Documentation/DocBook/kernel-api.html] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
If an I2C interrupt happens between disabling interface clock
and functional clock, the interrupt handler will produce an
external abort on non-linefetch error when trying to access
driver registers while interface clock is disabled.
This patch fixes the problem by saving and disabling i2c-omap
interrupt before turning off the clocks. Also disable functional
clock before the interface clock as suggested by Paul Walmsley.
Patch also renames enable/disable_clocks functions to unidle/idle
functions. Note that the driver is currently not taking advantage
of the idle interrupts. To use the idle interrupts, driver would
have to enable interface clock based on the idle interrupt
and dev->idle flag.
This patch has been tested in linux-omap tree with various omaps.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The i2c-bfin-twi driver doesn't support BF54x for now due to
missing header definitions causing the build to fail. Exclude
it for now, it will be enabled again later.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Ensure that client->driver is set to NULL if the probe() returns an
error (this keeps client->driver and client->dev.driver in sync).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch fixes an off-by-one error spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add the Intel ICH10 SMBus Controller DeviceID's and updates
Tolapai support.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When probing i2c-pca-isa writes to legacy ioports, which crashes the kernel
if there is no device at that port.
This patch adds a check_legacy_ioport call, so probe fails gracefully
and thus prevents the oops.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
While working on the PCA9564-platform driver, I sometimes had a glimpse at the
pxa-driver. I found some suspicious places, and this patch contains my
suggestions. Note: They are not tested, due to no hardware.
[JD: Some more fixes.]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Mike Rapoport <mike@compulab.co.il>
Tested-by: Eric Miao <ymiao3@marvell.com>
This fixes two warnings:
* unused static defined function decode_ICR() when
compiled without CONFIG_I2C_PXA_SLAVE
* a sparse warning about a void function returning
something
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Many I2C hwmon drivers define a driver ID but no other code references
these, meaning that they are useless. Discard them, along with a few
IDs which are defined but never used at all.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Use drivers/gpio/pca9539.c instead.
Signed-off-by: eric miao <eric.miao@marvell.com>
Acked-by: Ben Gardner <bgardner@wabtec.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch converts users of pci_enable_device_bars() to the new
pci_enable_device_{io,mem} interface.
The new API fits nicely, except maybe for the QLA case where a bit of
code re-organization might be a good idea but I prefer sticking to the
simple patch as I don't have hardware to test on.
I'll also need some feedback on the cs5520 change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* orion: (26 commits)
[ARM] Orion: implement power-off method for QNAP TS-109/209
[ARM] Orion: add support for QNAP TS-109/TS-209
[ARM] Orion: I2C support
[I2C] i2c-mv64xxx: Don't set i2c_adapter.retries
[I2C] Split mv643xx I2C platform support
[ARM] Orion: enable CONFIG_RTC_DRV_M41T80 for D-Link DNS-323
[ARM] Orion defconfig
[ARM] Orion: add support for Orion/MV88F5181 based D-Link DNS-323
[ARM] Orion: MV88F5181 support bits
[ARM] Orion: Buffalo/Revogear Kurobox Pro support
[ARM] OrionNAS RD board support
[ARM] Orion: support for Marvell Orion-2 (88F5281) Development Board
[ARM] Orion: common platform setup for Gigabit Ethernet port
[ARM] Orion: platform device registration for UART, USB and NAND
[ARM] Orion: system timer support
[ARM] Orion edge GPIO IRQ support
[ARM] Orion: IRQ support
[ARM] Orion: provide GPIO method for enabling hardware assisted blinking
[ARM] Orion: GPIO support
[ARM] Orion: programable address map support
...
Conflicts:
arch/arm/Kconfig
arch/arm/Makefile
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All the users of this driver explicitly specify the I2C bus numbers
to be used in their platform data. Make the driver respect that.
Signed-off-by: Kalle Pokki <kalle.pokki@eke.fi>
Cc: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Convert the i2c-au1550 bus driver to platform driver, and
register a platform device for the Alchemy Db/Pb series of
boards.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Zero-bytes transfers would leave the bus transaction unfinished
(no i2c stop is sent), with the following transfer actually
sending the slave address to the previously addressed device,
resulting in weird device failures (e.g. reset minute register
values in my RTC).
This patch instructs the controller to send an I2C STOP right after
the slave address in case of a zero-byte transfer.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Propagate the error values returned by i2c_wait() instead of overriding
them with a meaningless -1.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This adds a i2c_new_dummy() primitive to help work with devices
that consume multiple addresses, which include many I2C eeproms
and at least one RTC.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It is no longer required to hold adapter->clist_lock to call
i2c_check_addr.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
This goes on top of the patch removing most i2c_adapter.clients usage,
updating i2c_attach_client:
- Don't call device_register() while holding clist_lock. This
removes a self-deadlock when on the i2c_driver.probe() path,
for drivers that need to attach new devices (e.g. dummies).
- Remove a redundant address check. The driver model core does
this as a consequence of guaranteeing unique names.
- Move the "device registered" diagnostic so that it never lies;
previously, on error paths it would falsely report success.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The i2c_adapter.clients list of i2c_client nodes duplicates driver
model state. This patch starts removing that list, letting us remove
most existing users of those i2c-core lists.
* The core I2C code now iterates over the driver model's list instead
of the i2c-internal one in some places where it's safe:
- Passing a command/ioctl to each client, a mechanims
used almost exclusively by DVB adapters;
- Device address checking, in both i2c-core and i2c-dev.
* Provide i2c_verify_client() to use with driver model iterators.
* Flag the relevant i2c_adapter and i2c_client fields as deprecated,
to help prevent new users from appearing.
For the moment the list needs to stick around, since some issues show
up when deleting devices created by legacy I2C drivers. (They don't
follow standard driver model rules. Removing those devices can cause
self-deadlocks.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for another variant of the VT8237. I couldn't test
I2C block support but I assume it is present as well.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Checking the PCI function number doesn't add any value, and it makes
adding dynamic IDs to the driver more difficult. Drop this check.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The i2c-amd756 and i2c-viapro drivers make use of the driver_data
field of the PCI device ID. When adding device IDs dynamically (by
writing to the new_id sysfs file) you cannot set the value of this
field by default. It has to be allowed explicitly. Do that, and
check the value so that the user can't crash the kernel accidentally.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Add polling I2C transfer implementation for PXA I2C. This is needed
for cases where I2C transactions have to occur at times interrups are
disabled.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Allow i2c_transfer to be called in contexts where sleeping is not allowed.
It is the reponsability of the caller to ensure that the underlying i2c bus
driver will not sleep either.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The implementation is unsafe, and anyway one can achieve the same from
userspace using i2c-dev + i2cdetect.
Also tag i2c_sibyte_add_bus __init.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
I2C block read is supported since the ICH5. I couldn't get it to work
using the block buffer, so it's using the old-style byte-by-byte mode
for now.
Note: I'm also updating the driver author... The i2c-i801 driver was
really written by Mark Studebaker, even though he based his work on
the i2c-piix4 driver which was written by Philip Edelbrock.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Clear special mode bits (PEC, block buffer) at driver load time,
you never know in which state the device was left by its last user.
Also make sure that we reset the block buffer mode at the end of every
transaction, not only when PEC was used.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Provide a clearer documentation of which additional features each
ICH chip support, and which of these the driver supports.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move the tps65010 header file from the OMAP arch directory to the
more generic <linux/i2c/...> directory, and remove the spurious
dependency of this driver on OMAP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Rename the main mutex in i2c-core from core_lists to core_lock. This
makes more sense now that the redundant lists are gone.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
i2c_driver.list is superfluous, this list duplicates the one
maintained by the driver core. Drop it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
i2c_adapter.list is superfluous, this list duplicates the one
maintained by the driver core. Drop it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Use more standard prototypes for i2c_use_client() and
i2c_release_client(). The former now returns a pointer to the client,
and the latter no longer returns anything. This matches what all other
subsystems do.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Don't implement our own reference counting mechanism for i2c clients
when the driver model already has one.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
The framebuffer drivers for these pieces of hardware include support
for the DDC/I2C buses, so there is no need for separate drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
I2C adapter drivers are supposed to handle retries on nack by themselves
if they do, so there's no point in setting .retries if they don't.
As this retry mechanism is going away (at least in its current form),
clean this up now so that we don't get build failures later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch allows much of the I2C client address data to move from initdata
into text.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The 10-bit address support in i2c-algo-pcf is so heavily broken that
it can't have ever been used. Nobody ever complained, so I'll take it
that nobody needs it. Let's just delete it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Update comments and logging on return path for byte writes. NAK is
an error, to be reported or optionally ignored. Timeouts are always
errors. Lost arbitration is not currently handled, so don't even list
it as an option in the error message.
Don't return bogus EFAULT code for inappropriate NAK; EIO is better,
there is no bad userspace address in question.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix *LOTS* of whitespace goofs and checkpatch.pl warnings, strangely
parenthesized ternary expressions, and other CodingStyle glitches.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
remove #ifdef CONFIG_PXA27x .. #endif and use cpu_is_pxaXXXX() macros
so that a single binary can support PXA25x/PXA27x/PXA3xx at run-time.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch contains the overdue removal of three I2C drivers.
[JD: In fact only i2c-ixp4xx can be removed at the moment, the other two
platforms don't implement the generic GPIO layer yet.]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch contains the scheduled removal of legacy I2C RTC drivers with
replacement drivers.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use numbered adapter registration to always have the same hardware bus
show up at the same number.
PWRficient 1682M has three buses, they are all on the same PCI device but
different functions. So do the simple thing and register them based on
function number. Future products, if having a different number of busses,
are expected to have similar behaviour w.r.t. device/function layout.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
My guess is that all the chips supported by this driver support block
transactions and reset, but for now we play it safe and only list the
ones for which this was actually tested.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Oleg Ryjkov <olegr@olegr.ca>
I2C adapter drivers are supposed to handle retries on nack by themselves
if they do, so there's no point in setting .retries if they don't.
As this retry mechanism is going away (at least in its current form),
clean this up now so that we don't get build failures later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
The motivation for this change is to allow other chips, like the
Marvell Orion ARM SoC family, to use the existing i2c-mv64xxx driver.
Signed-off-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
If the registration of the second I2C channel fails, we really want to
unregister the first one before we return with an error.
While we're here, fix the printk right above so that it displays the
real driver name.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
This patch fixes bug #9581 reported by Marcio Buss. If kzalloc fails,
omap_i2c_write_reg() tries to reset an unallocated I2C controller.
Cc: Marcio Buss <marciobuss@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Build fix to the isp1301_omap driver ... this driver gets built
more often in the OMAP tree than in mainline, partly because the
defconfig for H2 (plus probably H3 and H4) needs updating.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is required to let hwmon drivers attach to the adapter.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Recent (i.e. 2005 and later) Sony Vaio laptops have names beginning
with VGN rather than PCG. Update the eeprom driver so that it
recognizes these.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The sysfs interface to DMI data takes care to not make the system
serial number and UUID world-readable, presumably due to privacy
concerns. For consistency, we should not let the eeprom driver
export these same strings to the world on Sony Vaio laptops.
Instead, only make them readable by root, as we already do for BIOS
passwords.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Turns out we don't actually check the status to see if there was a
device out there to talk to, just if we had a timeout when doing so.
Add the proper check, so we don't falsly think there are devices
on the bus that are not there, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
i2c_check_addr is only used inside i2c-core now, so we can make it
static and stop exporting it. Thanks to David Brownell for noticing.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Let i2c-dev deal properly with new-style i2c clients. Instead of
considering them always busy, it needs to check wether a driver is
bound to them or not.
This is still not completely correct, as the client could become
busy later, but the same problem already existed before new-style
clients were introduced. We'll want to fix it someday.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
This adds some "how does this work" comments to the i2c-dev driver,
plus separators between the three main components:
- The parallel list of i2c_adapters ("i2c_dev_list"), each of which
gets a "struct i2c_dev" and a /dev/i2c-X character special file.
- An i2cdev_driver gets adapter add/remove notifications, which are
used to maintain that list of adapters.
- Special file operations, which let userspace talk either directly to
the adapter (for i2c_msg operations) or through cached addressing info
using an anonymous i2c_client (never registered anywhere).
Plus there's the usual module load/unload record keeping.
After making sense of this code, I think that the anonymous i2c_client
is pretty shady. But since it's never registered, using this code with
a system set up for "new style" I2C drivers is no more complicated than
always using the I2C_SLAVE_FORCE ioctl (instead of I2C_SLAVE).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Most of these fixes were already submitted for old kernel versions, and were
approved, but for some reason they never made it into the releases.
Because this is a consolidation of a couple old missed patches, it touches both
Kconfigs and documentation texts.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
* Convert files to UTF-8.
* Also correct some people's names
(one example is Eißfeldt, which was found in a source file.
Given that the author used an ß at all in a source file
indicates that the real name has in fact a 'ß' and not an 'ss',
which is commonly used as a substitute for 'ß' when limited to
7bit.)
* Correct town names (Goettingen -> Göttingen)
* Update Eberhard Mönkeberg's address (http://lkml.org/lkml/2007/1/8/313)
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
i2c-pxa, rename BIT macro to PXA_BIT
BIT macro will be global definiton of (1 << x)
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nicolas Pitre <nico@cam.org>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Found these while looking at printk uses.
Add missing newlines to dev_<level> uses
Add missing KERN_<level> prefixes to multiline dev_<level>s
Fixed a wierd->weird spelling typo
Added a newline to a printk
Signed-off-by: Joe Perches <joe@perches.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Smart <James.Smart@Emulex.Com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Other/Some pr_*() macros are already defined in kernel.h, but pr_err() was
defined multiple times in several other places
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Tony Lindgren <tony@atomide.com>
Reviewed-by: Satyam Sharma <satyam@infradead.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (95 commits)
[ARM] 4578/1: CM-x270: PCMCIA support
[ARM] 4577/1: ITE 8152 PCI bridge support
[ARM] 4576/1: CM-X270 machine support
[ARM] pxa: Avoid pxa_gpio_mode() in gpio_direction_{in,out}put()
[ARM] pxa: move pxa_set_mode() from pxa2xx_mainstone.c to mainstone.c
[ARM] pxa: move pxa_set_mode() from pxa2xx_lubbock.c to lubbock.c
[ARM] pxa: Make cpu_is_pxaXXX dependent on configuration symbols
[ARM] pxa: PXA3xx base support
[NET] smc91x: fix PXA DMA support code
[SERIAL] Fix console initialisation ordering
[ARM] pxa: tidy up arch/arm/mach-pxa/Makefile
[ARM] Update arch/arm/Kconfig for drivers/Kconfig changes
[ARM] 4600/1: fix kernel build failure with build-id-supporting binutils
[ARM] 4599/1: Preserve ATAG list for use with kexec (2.6.23)
[ARM] Rename consistent_sync() as dma_cache_maint()
[ARM] 4572/1: ep93xx: add cirrus logic edb9307 support
[ARM] 4596/1: S3C2412: Correct IRQs for SDI+CF and add decoding support
[ARM] 4595/1: ns9xxx: define registers as void __iomem * instead of volatile u32
[ARM] 4594/1: ns9xxx: use the new gpio functions
[ARM] 4593/1: ns9xxx: implement generic clockevents
...
This patch is to add an abort function that will bring back the MCP51/55
controller if it was blocked by a block-read operation, in particular.
(When a slave sends a wrong byte count on a byte read, the host gets
locked up). I've only tested it on an MCP51 and MCP55. However, I'm
almost certain it will also work on MCP65, I just did not have the board
to test it on. Thus for now the abort function will only be called
if an MCP51/55 was detected.
Signed-off-by: Oleg Ryjkov <olegr@olegr.ca>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is the first part of the patch that adds a function to reset the
nvidia MCP51/55 i2c controller, if something bad happens to it (e.g.
a slave sends a wrong byte count during a block transaction).
This patch just adds nforce2_check_status function. It was originally
written by Hans-Frieder Vogt.
The reason that I'm the one sending it is:
- I relied on it for the second part of the patch,
- It makes the driver code cleaner/better.
Signed-off-by: Oleg Ryjkov <olegr@olegr.ca>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix a "mis-used register" problem on the AMD MIPS Alchemy au1550
I2C interface.
In summary, the programmable serial controller seems to hang the kernel
when I send a single 'address' byte on the I2C bus. The patch
essentially uses the PSC_SMBSTAT register's TE (transmit FIFO empty)
bit to check when the transmit FIFO is empty, instead of using the
PSC_SMBEVNT register's TU (transmit underflow) bit. Using the TE bit
fixed the hang problem.
Signed-off-by: Chris David <cd@chrisdavid.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Rename I2C_FUNC_SMBUS_HWPEC_CALC as I2C_FUNC_SMBUS_PEC, and list that
functionality as always available through the software implementation.
Update documentation accordingly (and list similar requirements).
The way it's currently packaged doesn't present the capability in a
useful way.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Mark the i2c-at91 driver BROKEN in Kconfig, and explain just
why it's broken. (Summary: hardware design issues.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This removes:
- An effectively unused hook: i2c_algorithm.algo_control.
- The i2c_control() call, used only by i2c-dev to call that
unused hook or set two barely supported adapter params.
(That param setting moves into i2c-dev.c ... still iffy
due to lack of locking, but no other changes.)
As shown by diffstat, this is a net code shrink. It also reduces the
complexity of the I2C adapter and /dev interfaces.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This removes NOP implementations of i2c_algorithm.algo_control.
With this change, there are no implementations of this hook in
the kernel.org tree ... that hook seems about ripe to remove.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The I2C_M_RECV_LEN calling convention for i2c_mesg.flags involves
playing games with reported buffer lengths. (They start out less
than their actual size, and the length is then modified to reflect
how many bytes were delivered ... which one hopes is less than the
presumed actual size.) Refuse to play such error prone games across
the boundary between userspace and kernel.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for multiple chips to i2c-stub. I've changed the memory
allocation scheme from static to dynamic, so that we don't waste too
much memory.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mark M. Hoffman <mhoffman@lightlink.com>
Remove this unneeded mutex. Indeed it was used to serialize access to
the hardware, but this is already done by the i2c-core layer, see
'bus_lock' mutex used by i2c_transfer().
Signed-off-by: Francis Moreau <francis.moro@gmail.com>
Acked-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Clarify use of the I2C_M_* flags by highlighting the fact that
most of them depend on I2C_FUNC_PROTOCOL_MANGLING.
Also provide kerneldoc for i2c_smbus_read_block_data() and also
for "struct i2c_msg".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Do not initialize the PCF8574 with an arbitrary value. Users will have
to write the initial value to sysfs themselves.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Aurelien Jarno <aurelien@aurel32.net>
