fd.o bz#21849
We were aligning to +16 dwords, instead of to the next 16dword
boundary in the ring. Fix the calculation to go to the next 16dword
boundary when space checking.
Signed-off-by: Dave Airlie <airlied@redhat.com>
allocating devname in the i915 driver was a hack originally and I
forgot to figure out how to do this properly back then.
So this is the cleaner version that just picks devname or driver name
in the irq code.
It removes the devname allocs from the i915 driver.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Freescale eSDHC controller has the special order for
the HOST version register. that is not same as the other's
registers. The address of HOSTVER in spec is 0xFE, and
we need use the in_be16(0xFE) to access it, not in_be16(0xFC).
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Especially with Sandisk SDHC cards, the second SWITCH command was failing
with a timeout and the card was not recognized at all. However if the
system was busy, or debugging was enabled, or a udelay(100) was inserted
before the second SWITCH command in the core code, then the timing was
so that the card started to work.
With some unusual block sizes, the data FIFO status doesn't indicate a
"empty" state right away when the data transfer is done. Queuing
another data transfer in that condition results in a transfer timeout.
The empty FIFO bit eventually get set by itself in less than 50 usecs
when it is not set right away. So let's just poll for that bit before
configuring the controller with a new data transfer.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Empirical evidences show that this is causing far more problems than it
solves when this mode is enabled in the host hardware. Amongst those
cards that are known to be non functional when this bit is set are:
A-Data "Speedy" 2GB SD card
Kodak 512MB SD card
Ativa 1GB MicroSD card
Marvell 8688 (WIFI/Bluetooth) SDIO card
Since those cards do work on other host controllers which do honnor the
hs timing, the issue must be with this particular host hardware.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
disable_irq() should wait for all running handlers to complete
before returning. As such, if it's used to disable an interrupt
from that interrupt's handler it will deadlock. This replaces
the dangerous instances with the _nosync() variant which doesn't
have this problem.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
We plan to use fsl,esdhc going forward as the base compatible so update
the driver to bind against it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
When a software timeout occurs in polling mode hardware was left in
an indeterminate state causing subsequent operations to block.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
This is a temporary workaround until the MMC stack can be fixed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Remove the __initdata annotation for the clock lookups, since they will
be needed when loading modules which use clk_get().
Tested-by: Agustín Ferrín Pozuelo <gatoguan-os@yahoo.com>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently, whenever an erratum workaround is enabled, it will be
applied whether or not the erratum is relevent for the CPU. This
patch changes this - we check the variant and revision fields in the
main ID register to determine which errata to apply.
We also avoid re-applying erratum 460075 if it has already been applied.
Applying this fix in non-secure mode results in the kernel failing to
boot (or even do anything.)
This fixes booting on some ARMv7 based platforms which otherwise
silently fail.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define ARCH_KMALLOC_MINALIGN in asm/cache.h
At the request of Russell also move ARCH_SLAB_MINALIGN to this file.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ideally we should have a directory of drivers and a link to the 'active'
driver. For now just show the first device which is effectively the existing
semantics without a warning.
This is an update on the original buggy patch that I then forgot to
resubmit. Confusingly it was proposed by Red Hat, written by Etched Pixels
fixed and submitted by Intel ...
Resolves-Bug: http://bugzilla.kernel.org/show_bug.cgi?id=9749
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This matches Bartlomiej's patch for ide_pci_generic:
c339dfdd65
In the libata case netcell has its own mini driver. I suspect this fix is
actually only needed for some firmware revs but it does no harm either way.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: prevent deadlock in xfs_qm_shake()
xfs: fix overflow in xfs_growfs_data_private
xfs: fix double unlock in xfs_swap_extents()
This patch fixes a bug which unconfigured struct tcf_proto keeps
chaining in tc_ctl_tfilter(), and avoids kernel panic in
cls_cgroup_classify() when we use cls_cgroup.
When we execute 'tc filter add', tcf_proto is allocated, initialized
by classifier's init(), and chained. After it's chained,
tc_ctl_tfilter() calls classifier's change(). When classifier's
change() fails, tc_ctl_tfilter() does not free and keeps tcf_proto.
In addition, cls_cgroup is initialized in change() not in init(). It
accesses unconfigured struct tcf_proto which is chained before
change(), then hits Oops.
Signed-off-by: Minoru Usui <usui@mxm.nes.nec.co.jp>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Tested-by: Minoru Usui <usui@mxm.nes.nec.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch to fix bad length checking in e1000. E1000 by default does two
things:
1) Spans rx descriptors for packets that don't fit into 1 skb on recieve
2) Strips the crc from a frame by subtracting 4 bytes from the length prior to
doing an skb_put
Since the e1000 driver isn't written to support receiving packets that span
multiple rx buffers, it checks the End of Packet bit of every frame, and
discards it if its not set. This places us in a situation where, if we have a
spanning packet, the first part is discarded, but the second part is not (since
it is the end of packet, and it passes the EOP bit test). If the second part of
the frame is small (4 bytes or less), we subtract 4 from it to remove its crc,
underflow the length, and wind up in skb_over_panic, when we try to skb_put a
huge number of bytes into the skb. This amounts to a remote DOS attack through
careful selection of frame size in relation to interface MTU. The fix for this
is already in the e1000e driver, as well as the e1000 sourceforge driver, but no
one ever pushed it to e1000. This is lifted straight from e1000e, and prevents
small frames from causing the underflow described above
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phy_power_down parameter to forcedeth: set to 1 to power down the
phy and disable the link when an interface goes down; set to 0 to always
leave the phy powered up.
The phy power state persists across reboots; Windows, some BIOSes, and
older versions of Linux don't bother to power up the phy again, forcing
users to remove all power to get the interface working (see
http://bugzilla.kernel.org/show_bug.cgi?id=13072). Leaving the phy
powered on is the safest default behavior. Users accustomed to seeing
the link state reflect the interface state and/or wanting to minimize
power consumption can set phy_power_down=1 if compatibility with other
OSes is not an issue.
Signed-off-by: Ed Swierk <eswierk@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible to recurse into filesystem from the memory
allocation, which deadlocks in xfs_qm_shake(). Add check
for __GFP_FS, and bail out if it is not set.
Signed-off-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Hedi Berriche <hedi@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
In the case where growing a filesystem would leave the last AG
too small, the fixup code has an overflow in the calculation
of the new size with one fewer ag, because "nagcount" is a 32
bit number. If the new filesystem has > 2^32 blocks in it
this causes a problem resulting in an EINVAL return from growfs:
# xfs_io -f -c "truncate 19998630180864" fsfile
# mkfs.xfs -f -bsize=4096 -dagsize=76288719b,size=3905982455b fsfile
# mount -o loop fsfile /mnt
# xfs_growfs /mnt
meta-data=/dev/loop0 isize=256 agcount=52,
agsize=76288719 blks
= sectsz=512 attr=2
data = bsize=4096 blocks=3905982455, imaxpct=5
= sunit=0 swidth=0 blks
naming =version 2 bsize=4096 ascii-ci=0
log =internal bsize=4096 blocks=32768, version=2
= sectsz=512 sunit=0 blks, lazy-count=0
realtime =none extsz=4096 blocks=0, rtextents=0
xfs_growfs: XFS_IOC_FSGROWFSDATA xfsctl failed: Invalid argument
Reported-by: richard.ems@cape-horn-eng.com
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
Regreesion from commit ef8f7fc, which rearranged the code in
xfs_swap_extents() leading to double unlock of xfs inode ilock.
That resulted in xfs_fsr deadlocking itself on platforms, which
don't handle double unlock of rw_semaphore nicely. It caused the
count go negative, which represents the write holder, without
really having one. ia64 is one of the platforms where deadlock
was easily reproduced and the fix was tested.
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
Add fan_max description.
Add fan limit alarm 'max_alarm' to the alarm section.
Signed-off-by: Christian Engelmayer <christian.engelmayer@frequentis.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The remove function uses __devexit, so the .remove assignment needs
__devexit_p() to fix a build error with hotplug disabled.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Several EISA device IDs for 3c509 family network cards are missing from
the driver, making the cards unusable in their EISA mode. Here's a fix to
add them based on the EISA configuration files distributed by 3Com and our
eisa.ids database.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds me as the maintainer of the CPMAC (AR7)
Ethernet driver.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix the following 'make headers_check' warnings:
usr/include/linux/net_dropmon.h:7: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warnings:
usr/include/linux/auto_fs.h:17: include of <linux/types.h> is preferred over <asm/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
A quirk that we've always supported is having an sg entry that's
bigger than a page, or more generally an sg entry that crosses
page boundaries. Even though it would be better to explicitly have
to sg entries for this, we need to support it for the existing users,
in particular, IPsec.
The new ahash sg walking code did try to handle this, but there was
a bug where we didn't increment the page so kept on walking on the
first page over an dover again.
This patch fixes it.
Tested-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We need to explicitly mark words 85-87 as valid ones since
firmware doesn't do it.
This should fix support for LBA48 and FLUSH CACHE [EXT] command
which stopped working after we applied more strict checking of
identify words in:
commit 942dcd85bf
("ide: idedisk_supports_lba48() -> ata_id_lba48_enabled()")
and
commit 4b58f17d7c
("ide: ide_id_has_flush_cache() -> ata_id_flush_enabled()")
Reported-and-tested-by: "Trevor Hemsley" <trevor.hemsley@ntlworld.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
fsldma: Fix compile warnings
fsldma: fix memory leak on error path in fsl_dma_prep_memcpy()
fsldma: snooping is not enabled for last entry in descriptor chain
fsldma: fix infinite loop on multi-descriptor DMA chain completion
fsldma: fix "DMA halt timeout!" errors
fsldma: fix check on potential fdev->chan[] overflow
fsldma: update mailling list address in MAINTAINERS
The nilfs_cpfile_delete_checkpoints() wrongly skips brelse() for the
header block of checkpoint file in case of errors. This fixes the
leak bug.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Gary Lin reports that a new device id needs to be added to the atl1e in
order to get some new Asus hardware to work properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
