The corruption check is enabled in Kconfig by default, but disabled at runtime.
This patch adds several kernel parameters to control the corruption
check's behaviour; these are documented in kernel-parameters.txt.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some BIOSes have been observed to corrupt memory in the low 64k. This
change:
- Reserves all memory which does not have to be in that area, to
prevent it from being used as general memory by the kernel. Things
like the SMP trampoline are still in the memory, however.
- Clears the reserved memory so we can observe changes to it.
- Adds a function check_for_bios_corruption() which checks and reports on
memory becoming unexpectedly non-zero. Currently it's called in the
x86 fault handler, and the powermanagement debug output.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (98 commits)
V4L/DVB (8881): gspca: After 'while (retry--) {...}', retry will be -1 but not 0.
V4L/DVB (8880): PATCH: Fix parents on some webcam drivers
V4L/DVB (8877): b2c2 and bt8xx: udelay to mdelay
V4L/DVB (8876): budget: udelay changed to mdelay
V4L/DVB (8874): gspca: Adjust hstart for sn9c103/ov7630 and update usb-id's.
V4L/DVB (8873): gspca: Bad image offset with rev012a of spca561 and adjust exposure.
V4L/DVB (8872): gspca: Bad image format and offset with rev072a of spca561.
V4L/DVB (8870): gspca: Fix dark room problem with sonixb.
V4L/DVB (8869): gspca: Move the Sonix webcams with TAS5110C1B from sn9c102 to gspca.
V4L/DVB (8868): gspca: Support for vga modes with sif sensors in sonixb.
V4L/DVB (8844): dabusb_fpga_download(): fix a memory leak
V4L/DVB (8843): tda10048_firmware_upload(): fix a memory leak
V4L/DVB (8842): vivi_release(): fix use-after-free
V4L/DVB (8840): dib0700: add basic support for Hauppauge Nova-TD-500 (84xxx)
V4L/DVB (8839): dib0700: add comment to identify 35th USB id pair
V4L/DVB (8837): dvb: fix I2C adapters name size
V4L/DVB (8835): gspca: Same pixfmt as the sn9c102 driver and raw Bayer added in sonixb.
V4L/DVB (8834): gspca: Have a bigger buffer for sn9c10x compressed images.
V4L/DVB (8833): gspca: Cleanup the sonixb code.
V4L/DVB (8832): gspca: Bad pixelformat of vc0321 webcams.
...
* 'release-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-acpi-2.6:
acer-wmi: remove debugfs entries upon unloading
ACPI: Avoid bogus timeout about SMbus check
fujitsu-laptop: fix regression for P8010 in 2.6.27-rc
ACPI: Make Len Brown the ACPI maintainer again
ACPI: thinkpad-acpi: wan radio control is not experimental
PNPACPI: ignore the producer/consumer bit for extended IRQ descriptors
acpi: add checking for NULL early param
ACPI: Fix typo in "Disable MWAIT via DMI on broken Compal board"
ACPI: Fix now signed module parameter.
ACPI: Change package length error to warning
ACPI: Fix now signed module parameter.
As noted by Gu Rui in http://bugzilla.kernel.org/show_bug.cgi?id=11444,
there is a typo in Documentation/sound/alsa/ALSA-Configuration.txt.
After checking the source (sound/pci/hda/hda_intel.c), the report
looks correct to me.
Signed-off-by: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds a generic infrastructure for policy-based dequeueing of
TX packets and provides two policies:
* a simple FIFO policy (which is the default) and
* a priority based policy (set via socket options).
Both policies honour the tx_qlen sysctl for the maximum size of the write
queue (can be overridden via socket options).
The priority policy uses skb->priority internally to assign an u32 priority
identifier, using the same ranking as SO_PRIORITY. The skb->priority field
is set to 0 when the packet leaves DCCP. The priority is supplied as ancillary
data using cmsg(3), the patch also provides the requisite parsing routines.
Signed-off-by: Tomasz Grobelny <tomasz@grobelny.oswiecenia.net>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This adds full support for local/remote Sequence Window feature, from which the
* sequence-number-validity (W) and
* acknowledgment-number-validity (W') windows
derive as specified in RFC 4340, 7.5.3.
Specifically, the following changes are introduced:
* integrated new socket fields into dccp_sk;
* updated the update_gsr/gss routines with regard to these fields;
* updated handler code: the Sequence Window feature is located at the TX side,
so the local feature is meant if the handler-rx flag is false;
* the initialisation of `rcv_wnd' in reqsk is removed, since
- rcv_wnd is not used by the code anywhere;
- sequence number checks are not done in the LISTEN state (cf. 7.5.3);
- dccp_check_req checks the Ack number validity more rigorously;
* the `struct dccp_minisock' became empty and is now removed.
Until the handshake completes with activating negotiated values, the local/remote
Sequence-Window values are undefined and thus can not reliably be estimated.
This issue is addressed in a separate patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This removes the use of the sysctl and the minisock variable for the Send Ack
Vector feature, which is now handled fully dynamically via feature negotiation;
i.e. when CCID2 is enabled, Ack Vectors are automatically enabled (as per
RFC 4341, 4.).
Using a sysctl in parallel to this implementation would open the door to
crashes, since much of the code relies on tests of the boolean minisock /
sysctl variable. Thus, this patch replaces all tests of type
if (dccp_msk(sk)->dccpms_send_ack_vector)
/* ... */
with
if (dp->dccps_hc_rx_ackvec != NULL)
/* ... */
The dccps_hc_rx_ackvec is allocated by the dccp_hdlr_ackvec() when feature
negotiation concluded that Ack Vectors are to be used on the half-connection.
Otherwise, it is NULL (due to dccp_init_sock/dccp_create_openreq_child),
so that the test is a valid one.
The activation handler for Ack Vectors is called as soon as the feature
negotiation has concluded at the
* server when the Ack marking the transition RESPOND => OPEN arrives;
* client after it has sent its ACK, marking the transition REQUEST => PARTOPEN.
Adding the sequence number of the Response packet to the Ack Vector has been
removed, since
(a) connection establishment implies that the Response has been received;
(b) the CCIDs only look at packets received in the (PART)OPEN state, i.e.
this entry will always be ignored;
(c) it can not be used for anything useful - to detect loss for instance, only
packets received after the loss can serve as pseudo-dupacks.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Updating the NDP count feature is handled automatically now:
* for CCID-2 it is disabled, since the code does not use NDP counts;
* for CCID-3 it is enabled, as NDP counts are used to determine loss lengths.
Allowing the user to change NDP values leads to unpredictable and failing
behaviour, since it is then possible to disable NDP counts even when they
are needed (e.g. in CCID-3).
This means that only those user settings are sensible that agree with the
values for Send NDP Count implied by the choice of CCID. But those settings
are already activated by the feature negotiation (CCID dependency tracking),
hence this form of support is redundant.
At startup the initialisation of the NDP count feature is with the default
value of 0, which is done implicitly by the zeroing-out of the socket when
it is allocated. If the choice of CCID or feature negotiation enables NDP
count, this will then be updated via the NDP activation handler.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
The TX/RX CCIDs of the minisock are now redundant: similar to the Ack Vector
case, their value equals initially that of the sysctl, but at the end of
feature negotiation may be something different.
The old interface removed by this patch thus has been replaced by the newer
interface to dynamically query the currently loaded CCIDs earlier in this
patch set.
Also removed the constructors for the TX CCID and the RX CCID, since the
switch rx/non-rx is done by the handler in minisocks.c (and the handler is
the only place in the code where CCIDs are loaded).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
With this patch, TX/RX CCIDs can now be changed on a per-connection basis, which
overrides the defaults set by the global sysctl variables for TX/RX CCIDs.
To make full use of this facility, the remaining patches of this patch set are
needed, which track dependencies and activate negotiated feature values.
Note on the maximum number of CCIDs that can be registered:
-----------------------------------------------------------
The maximum number of CCIDs that can be registered on the socket is constrained
by the space in a Confirm/Change feature negotiation option.
The space in these in turn depends on the size of header options as defined
in RFC 4340, 5.8. Since this is a recurring constant, it has been moved from
ackvec.h into linux/dccp.h, clarifying its purpose.
Relative to this size, the maximum number of CCID identifiers that can be
present in a Confirm option (which always consumes 1 byte more than a Change
option, cf. 6.1) is 2 bytes less than the maximum TLV size: one for the
CCID-feature-type and one for the selected value.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This patch deprecates the Ack Ratio sysctl, since
* Ack Ratio is entirely ignored by CCID-3 and CCID-4,
* Ack Ratio currently doesn't work in CCID-2 (i.e. is always set to 1);
* even if it would work in CCID-2, there is no point for a user to change it:
- Ack Ratio is constrained by cwnd (RFC 4341, 6.1.2),
- if Ack Ratio > cwnd, the system resorts to spurious RTO timeouts
(since waiting for Acks which will never arrive in this window),
- cwnd is not a user-configurable value.
The only reasonable place for Ack Ratio is to print it for debugging. It is
planned to do this later on, as part of e.g. dccp_probe.
With this patch Ack Ratio is now under full control of feature negotiation:
* Ack Ratio is resolved as a dependency of the selected CCID;
* if the chosen CCID supports it (i.e. CCID == CCID-2), Ack Ratio is set to
the default of 2, following RFC 4340, 11.3 - "New connections start with Ack
Ratio 2 for both endpoints";
* what happens then is part of another patch set, since it concerns the
dynamic update of Ack Ratio while the connection is in full flight.
Thanks to Tomasz Grobelny for discussion leading up to this patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This provides a data structure to record which CCIDs are locally supported
and three accessor functions:
- a test function for internal use which is used to validate CCID requests
made by the user;
- a copy function so that the list can be used for feature-negotiation;
- documented getsockopt() support so that the user can query capabilities.
The data structure is a table which is filled in at compile-time with the
list of available CCIDs (which in turn depends on the Kconfig choices).
Using the copy function for cloning the list of supported CCIDs is useful for
feature negotiation, since the negotiation is now with the full list of available
CCIDs (e.g. {2, 3}) instead of the default value {2}. This means negotiation
will not fail if the peer requests to use CCID3 instead of CCID2.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
-Add usb id for 093a:2624 (pac7302)
-Report some controls to userspace with 7302 only, as they are 7302 only
-Add gain and exposure controls
-Add autogain
-Fix 7302 imaged being mirrored by default
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch adapted from a patch to gspcav1 made by the google microdia group.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Update Documentation/filesystems/proc.txt: it describes the file
auto_msgmni intoduced to enable/disable msgmni automatic recomputing upon
memory add/remove (see thread http://lkml.org/lkml/2008/7/4/27). Also
added a description for msgmni (this filex is only listed in
Documentation/sysctl/kernel.txt).
Signed-off-by: Nadia Derbey <Nadia.Derbey@bull.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the location of the NTFS homepage in several files.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the new firmware infrastructure in 2.6.27, some files are generated and shouldn't be
diffed; add these 2 to the "dontdiff" file
Signed-off-by: Arjan van de Ven <arjan@Linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Added the support of Toshiba RX1 laptop with ALC262 codec chip.
Related ALSA bug#3386:
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3386
Signed-off-by: Hiroshi Miura <miurahr@acm.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the descriptions of missing model values.
Also, fixed the model strings of a few new models to a standard style.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The WWAN radio control has been working well for over three years,
and is no longer experimental.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Commit ecd29476ae removed the
"disable_8254_timer" and "enable_8254_timer" kernel parameters from
the kernel but did not remove the references to them from two
files in the Documentation directory: kernel-parameters.txt and
x86/x86_64/boot-options.txt.
This change completes the removal.
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In August 2006 I posted a patch generating a minimal SELinux policy. This
week, David P. Quigley posted an updated version of that as a patch against
the kernel. It also had nice logic for auto-installing the policy.
Following is David's original patch intro (preserved especially
bc it has stats on the generated policies):
se interested in the changes there were only two significant
changes. The first is that the iteration through the list of classes
used NULL as a sentinel value. The problem with this is that the
class_to_string array actually has NULL entries in its table as place
holders for the user space object classes.
The second change was that it would seem at some point the initial sids
table was NULL terminated. This is no longer the case so that iteration
has to be done on array length instead of looking for NULL.
Some statistics on the policy that it generates:
The policy consists of 523 lines which contain no blank lines. Of those
523 lines 453 of them are class, permission, and initial sid
definitions. These lines are usually little to no concern to the policy
developer since they will not be adding object classes or permissions.
Of the remaining 70 lines there is one type, one role, and one user
statement. The remaining lines are broken into three portions. The first
group are TE allow rules which make up 29 of the remaining lines, the
second is assignment of labels to the initial sids which consist of 27
lines, and file system labeling statements which are the remaining 11.
In addition to the policy.conf generated there is a single file_contexts
file containing two lines which labels the entire system with base_t.
This policy generates a policy.23 binary that is 7920 bytes.
(then a few versions later...):
The new policy is 587 lines (stripped of blank lines) with 476 of those
lines being the boilerplate that I mentioned last time. The remaining
111 lines have the 3 lines for type, user, and role, 70 lines for the
allow rules (one for each object class including user space object
classes), 27 lines to assign types to the initial sids, and 11 lines for
file system labeling. The policy binary is 9194 bytes.
Changelog:
Aug 26: Added Documentation/SELinux.txt
Aug 26: Incorporated a set of comments by Stephen Smalley:
1. auto-setup SELINUXTYPE=dummy
2. don't auto-install if selinux is enabled with
non-dummy policy
3. don't re-compute policy version
4. /sbin/setfiles not /usr/sbin/setfiles
Aug 22: As per JMorris comments, made sure make distclean
cleans up the mdp directory.
Removed a check for file_contexts which is now
created in the same file as the check, making it
superfluous.
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: David Quigley <dpquigl@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
This patch adds kernel doc for the completion feature.
An error in the split-man.pl PERL snippet in kernel-doc-nano-HOWTO.txt is
also fixed.
Signed-off-by: Kevin Diggs <kevdig@hypersurf.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Added the basic support of AD1882A codec chip.
It's almost compatible with AD1882, but with a digital mic and some
differences in connections.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
By calling pcmcia_loop_config(), a pcmcia driver can iterate over all
available configuration options. During a driver's probe() phase, one
doesn't need to use pcmcia_get_{first,next}_tuple, pcmcia_get_tuple_data
and pcmcia_parse_tuple directly in most if not all cases.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: Update documentation to remind users to update mke2fs.conf
ext4: Fix small file fragmentation
ext4: Initialize writeback_index to 0 when allocating a new inode
ext4: make sure ext4_has_free_blocks returns 0 for ENOSPC
ext4: journal credit fix for the delayed allocation's writepages() function
ext4: Rework the ext4_da_writepages() function
ext4: journal credits reservation fixes for DIO, fallocate
ext4: journal credits reservation fixes for extent file writepage
ext4: journal credits calulation cleanup and fix for non-extent writepage
ext4: Fix bug where we return ENOSPC even though we have plenty of inodes
ext4: don't try to resize if there are no reserved gdt blocks left
ext4: Use ext4_discard_reservations instead of mballoc-specific call
ext4: Fix ext4_dx_readdir hash collision handling
ext4: Fix delalloc release block reservation for truncate
ext4: Fix potential truncate BUG due to i_prealloc_list being non-empty
ext4: Handle unwritten extent properly with delayed allocation
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] pata_it821x: fix warning
libata: Fix a large collection of DMA mode mismatches
ahci: sis controllers actually can do PMP
pata_via: clean up recent tf_load changes
libata: restore SControl on detach
libata: use ata_link_printk() when printing SError
libata: always do follow-up SRST if hardreset returned -EAGAIN
libata: fix EH action overwriting in ata_eh_reset()
sata_mv: add the Gen IIE flag to the SoC devices.
ata_piix: IDE Mode SATA patch for Intel Ibex Peak DeviceIDs
ahci: RAID mode SATA patch for Intel Ibex Peak DeviceIDs
sata_mv: don't issue two DMA commands concurrently
libata: implement no[hs]rst force params
Implement force params nohrst, nosrst and norst. This is to work
around reset related problems and ease debugging.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Hi,
This patch adds SubmitChecklist translated into Japanese to
Documentation/ja_JP directory.
The translated SubmitChecklist has already been reviewed by JF project.
SubmitChecklist is one of the important policy documents.
So, I would like to merge into 2.6.27.
Signed-off-by: Takenori Nagano <t-nagano@ah.jp.nec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Documentation update for PAT. Reflect the latest API details.
Also, adds details about ways to get more info in order to debug PAT.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rewrite of the CFS documentation - because the old one was sorely
out-dated.
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
"bootmem_debug" is not mentioned in kernel-parameters.txt. Recently I
had to use that kernel option and I think it should be documented.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Johannes Weiner <hannes@saeurebad.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (22 commits)
[SCSI] ibmvfc: Driver version 1.0.2
[SCSI] ibmvfc: Add details to async event log
[SCSI] ibmvfc: Sanitize response lengths
[SCSI] ibmvfc: Fix for lost async events
[SCSI] ibmvfc: Fixup host state during reinit
[SCSI] ibmvfc: Fix another hang on module removal
[SCSI] ibmvscsi: Fixup desired DMA value for shared memory partitions
[SCSI] megaraid_sas: remove sysfs dbg_lvl world writeable permissions
[SCSI] qla2xxx: Update version number to 8.02.01-k7.
[SCSI] qla2xxx: Explicitly tear-down vports during PCI remove_one().
[SCSI] qla2xxx: Reference proper ha during SBR handling.
[SCSI] qla2xxx: Set npiv_supported flag for FCoE HBAs.
[SCSI] qla2xxx: Don't leak SG-DMA mappings while aborting commands.
[SCSI] qla2xxx: Correct vport-state management issues during ISP-ABORT.
[SCSI] qla2xxx: Correct synchronization of software/firmware fcport states.
[SCSI] scsi_dh: Initialize lun_state in check_ownership()
[SCSI] scsi_dh: Do not use scsilun in rdac hardware handler
[SCSI] megaraid_sas: version and Documentation Update
[SCSI] megaraid_sas: add new controllers (0x78 0x79)
[SCSI] megaraid_sas: add the shutdown DCMD cmd to driver shutdown routine
...
Add security/inode.c functions to the kernel-api docbook.
Use '%' on constants in kernel-doc notation.
Fix several typos/spellos in security function descriptions.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Morris <jmorris@namei.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (94 commits)
pkt_sched: Prevent livelock in TX queue running.
Revert "pkt_sched: Add BH protection for qdisc_stab_lock."
Revert "pkt_sched: Protect gen estimators under est_lock."
pkt_sched: remove bogus block (cleanup)
nf_nat: use secure_ipv4_port_ephemeral() for NAT port randomization
netfilter: ctnetlink: sleepable allocation with spin lock bh
netfilter: ctnetlink: fix sleep in read-side lock section
netfilter: ctnetlink: fix double helper assignation for NAT'ed conntracks
netfilter: ipt_addrtype: Fix matching of inverted destination address type
dccp: Fix panic caused by too early termination of retransmission mechanism
pkt_sched: Don't hold qdisc lock over qdisc_destroy().
pkt_sched: Add lockdep annotation for qdisc locks
pkt_sched: Never schedule non-root qdiscs.
removed unused #include <version.h>
rt2x00: Fix txdone_entry_desc_flags
b43: Fix for another Bluetooth Coexistence SPROM Programming error for BCM4306
mac80211: remove kdoc references to IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE
p54u: reset skb's data/tail pointer on requeue
p54: move p54_vdcf_init to the right place.
iwlwifi: fix printk newlines
...
Guard rfkill controllers attached to a rfkill class against state changes
after class suspend has been issued.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* master.kernel.org:/home/rmk/linux-2.6-arm: (38 commits)
[ARM] 5191/1: ARM: remove CVS keywords
[ARM] pxafb: fix the warning of incorrect lccr when lcd_conn is specified
[ARM] pxafb: add flag to specify output format on LDD pins when base is RGBT16
[ARM] pxafb: fix the incorrect configuration of GPIO77 as ACBIAS for TFT LCD
[ARM] 5198/1: PalmTX: PCMCIA fixes
[ARM] Fix a pile of broken watchdog drivers
[ARM] update mach-types
[ARM] 5196/1: fix inline asm constraints for preload
[ARM] 5194/1: update .gitignore
[ARM] add proc-macros.S include to proc-arm940 and proc-arm946
[ARM] 5192/1: ARM TLB: add v7wbi_{possible,always}_flags to {possible,always}_tlb_flags
[ARM] 5193/1: Wire up missing syscalls
[ARM] traps: don't call undef hook functions with spinlock held
[ARM] 5183/2: Provide Poodle LoCoMo GPIO names
[ARM] dma-mapping: provide sync_range APIs
[ARM] dma-mapping: improve type-safeness of DMA translations
[ARM] Kirkwood: instantiate the orion_spi driver in the platform code
[ARM] prevent crashing when too much RAM installed
[ARM] Kirkwood: Instantiate mv_xor driver
[ARM] Orion: Instantiate mv_xor driver for 5182
...
Signed-off-by: Bo Yang <bo.yang@lsi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* 'linux-next' of git://git.infradead.org/~dedekind/ubifs-2.6: (29 commits)
UBIFS: xattr bugfixes
UBIFS: remove unneeded check
UBIFS: few commentary fixes
UBIFS: fix budgeting request alignment in xattr code
UBIFS: improve arguments checking in debugging messages
UBIFS: always set i_generation to 0
UBIFS: correct spelling of "thrice".
UBIFS: support splice_write
UBIFS: minor tweaks in commit
UBIFS: reserve more space for index
UBIFS: print pid in dump function
UBIFS: align inode data to eight
UBIFS: improve budgeting checks
UBIFS: correct orphan deletion order
UBIFS: fix typos in comments
UBIFS: do not union creat_sqnum and del_cmtno
UBIFS: optimize deletions
UBIFS: increment commit number earlier
UBIFS: remove another unneeded function parameter
UBIFS: remove unneeded function parameter
...
Minor documentation update to reflect the current full name of the power
management hardware interface and reflows the text a bit.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With man-pages-3.07, the numa_maps documentation home is now proc(5), so
the reference in Documentation/vm/page_migration needs updating.
(Cliff/Lee are removing numa_maps.5 from the numactl package.) Also, the
download location for the numactl package changed a while back. This
patch fixes both things, as well as a typo (provided-->provides).
Signed-off-by: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Cliff Wickman <cpw@sgi.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All of the in-tree uses of list_for_each_rcu() have been converted to
list_for_each_entry_rcu(), so list_for_each_rcu() can now be removed.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Added the ignore_ctl_error parameter to enable/disable the control-error
handling for mixer interfaces. It was a hard-coded ifdef, and now you
can change it more easily.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the missing description of module parameters of usb-audio driver
to ALSA-Configuration.txt.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add support for the Asus Xonar D1. It is the same as the DX, but
without the external power detection.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
this mentions a new deadlock due to advanced power management.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the auerswald USB driver from the linux kernel
2.6.26.
This driver was included into the kernel mainly to connect to the ISDN
framework. This was done in linux 2.4.x. For 2.6.x, due to the fragile
and moving ISDN support, this connection was never realized, and the
only use of this driver was for device configuration. In the age of DSL,
the demand of ISDN support is getting very low.
Meanwhile, with the advent of libusb, an userspace driver was done for
the device configuration which works fine for linux and mac. (Thanks to
the libusb developers!). The userspace driver is downloadable from the
auerswald web site.
So this driver is obsolete now and has to be removed. Many thanks to all
developers which helped me to bring this driver up and working.
Signed-off-by: Wolfgang Muees <wolfgang@iksw-muees.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Introduced snd_BUG_ON() macro as a replacement of snd_assert() macro.
snd_assert() is pretty ugly as it has the control flow in its argument.
OTOH, snd_BUG_ON() behaves like a normal conditional, thus it's much
easier to read the flow.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix printf format type warnings (seen on alpha & ia64):
Documentation/accounting/getdelays.c:206: warning: format '%15llu' expects type 'long long unsigned int', but argument 6 has type '__u64'
Documentation/accounting/getdelays.c:206: warning: format '%15llu' expects type 'long long unsigned int', but argument 7 has type '__u64'
Documentation/accounting/getdelays.c:206: warning: format '%15llu' expects type 'long long unsigned int', but argument 8 has type '__u64'
Documentation/accounting/getdelays.c:206: warning: format '%15llu' expects type 'long long unsigned int', but argument 9 has type '__u64'
Documentation/accounting/getdelays.c:206: warning: format '%15llu' expects type 'long long unsigned int', but argument 12 has type '__u64'
Documentation/accounting/getdelays.c:206: warning: format '%15llu' expects type 'long long unsigned int', but argument 13 has type '__u64'
Documentation/accounting/getdelays.c:206: warning: format '%15llu' expects type 'long long unsigned int', but argument 16 has type '__u64'
Documentation/accounting/getdelays.c:206: warning: format '%15llu' expects type 'long long unsigned int', but argument 17 has type '__u64'
Documentation/accounting/getdelays.c:214: warning: format '%15llu' expects type 'long long unsigned int', but argument 4 has type '__u64'
Documentation/accounting/getdelays.c:214: warning: format '%15llu' expects type 'long long unsigned int', but argument 5 has type '__u64'
Documentation/accounting/getdelays.c:221: warning: format '%llu' expects type 'long long unsigned int', but argument 2 has type '__u64'
Documentation/accounting/getdelays.c:221: warning: format '%llu' expects type 'long long unsigned int', but argument 3 has type '__u64'
Documentation/accounting/getdelays.c:221: warning: format '%llu' expects type 'long long unsigned int', but argument 4 has type '__u64'
Documentation/accounting/getdelays.c:221: warning: format '%llu' expects type 'long long unsigned int', but argument 5 has type '__u64'
Documentation/accounting/getdelays.c:221: warning: format '%llu' expects type 'long long unsigned int', but argument 6 has type '__u64'
Documentation/accounting/getdelays.c:236: warning: 'cmd_type' may be used uninitialized in this function
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Documentation/networking/ifenslave.c:1084: warning: pointer targets in assignment differ in signedness
>From include/linux/socket.h:
* 1003.1g requires sa_family_t and that sa_data is char.
and from SUSv3:
(http://www.opengroup.org/onlinepubs/009695399/basedefs/sys/socket.h.html)
The <sys/socket.h> header shall define the sockaddr structure that includes at least the following members:
sa_family_t sa_family Address family.
char sa_data[] Socket address (variable-length data).
<end SUSv3>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add MODULE_LICENSE() to DocBook/procfs_example.c since modpost complained
about a missing license there.
Remove tty procfs removal since the creation was deleted long ago
(http://git.kernel.org/?p=linux/kernel/git/tglx/history.git;a=commitdiff;h=5ad9cb65e9b15e5b83e2dd1c10a4bcaccc4ec644).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: <J.A.K.Mouw@its.tudelft.nl>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently source files in the Documentation/ sub-dir can easily bit-rot
since they are not generally buildable, either because they are hidden in
text files or because there are no Makefile rules for them. This needs to
be fixed so that the source files remain usable and good examples of code
instead of bad examples.
Add the ability to build source files that are in the Documentation/ dir.
Add to Kconfig as "BUILD_DOCSRC" config symbol.
Use "CONFIG_BUILD_DOCSRC=1 make ..." to build objects from the
Documentation/ sources. Or enable BUILD_DOCSRC in the *config system.
However, this symbol depends on HEADERS_CHECK since the header files need
to be installed (for userspace builds).
Built (using cross-tools) for x86-64, i386, alpha, ia64, sparc32,
sparc64, powerpc, sh, m68k, & mips.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
s390 doesn't support the additional_cpus kernel parameter anymore since a
long time. So we better update the code and documentation to reflect
that.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that the driver is removed we should also remove the entry in
Documentation/feature-removal-schedule.txt
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This shows up when trying to bridge:
tap0: received packet with own address as source address
As Max Krasnyansky points out, there's no reason to give the guest the
same mac address as the TUN device.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Max Krasnyansky <maxk@qualcomm.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Remove include/linux/harrier_defs.h
powerpc: Do not ignore arch/powerpc/include
powerpc: Delete completed "ppc removal" task from feature removal file
powerpc/mm: Fix attribute confusion with htab_bolt_mapping()
powerpc/pci: Don't keep ISA memory hole resources in the tree
powerpc: Zero fill the return values of rtas argument buffer
powerpc/4xx: Update defconfig files for 2.6.27-rc1
powerpc/44x: Incorrect NOR offset in Warp DTS
powerpc/44x: Warp DTS changes for board updates
powerpc/4xx: Cleanup Warp for i2c driver changes.
powerpc/44x: Adjust warp-nand resource end address
* 'for-linus-merged' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5177/1: arm/mach-sa1100/Makefile: remove CONFIG_SA1100_USB
[ARM] 5166/1: magician: add MAINTAINERS entry
[ARM] fix pnx4008 build errors
[ARM] Fix SMP booting with non-zero PHYS_OFFSET
[ARM] 5185/1: Fix spi num_chipselect for lubbock
[ARM] Move include/asm-arm/arch-* to arch/arm/*/include/mach
[ARM] Add support for arch/arm/mach-*/include and arch/arm/plat-*/include
[ARM] Remove asm/hardware.h, use asm/arch/hardware.h instead
[ARM] Eliminate useless includes of asm/mach-types.h
[ARM] Fix circular include dependency with IRQ headers
avr32: Use <mach/foo.h> instead of <asm/arch/foo.h>
avr32: Introduce arch/avr32/mach-*/include/mach
avr32: Move include/asm-avr32 to arch/avr32/include/asm
[ARM] sa1100_wdt: use reset_status to remember watchdog reset status
[ARM] pxa: introduce reset_status and clear_reset_status for driver's usage
[ARM] pxa: introduce reset.h for reset specific header information
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (99 commits)
pkt_sched: Fix actions referencing
bnx2x: fix logical op
tcp: (whitespace only) fix confusing indentation
pkt_sched: Fix qdisc config when link is down.
[Bluetooth] Add full quirk implementation for btusb driver
[Bluetooth] Removal of unnecessary ignore module parameter
[Bluetooth] Add parameters to control BNEP header compression
ath9k: Revamp wireless mode usage
ath9k: More unused macros
ath9k: Remove a few unused macros and fix indentation
ath9k: Use mac80211's band macros and remove enum hal_freq_band
ath9k: Remove redundant data structure ath9k_txq_info
ath9k: Cleanup data structures related to HW capabilities
ath9k: work around gcc ICEs
ath9k: Add new Atheros IEEE 802.11n driver
ath5k: remove Atheros 11n devices from supported list
list.h: add list_cut_position()
list.h: Add list_splice_tail() and list_splice_tail_init()
p54: swap short slot time dcf values
rt2x00: Block all unsupported modes
...
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
xen-blkfront.c: make blkif_ioctl() static
bio: make use of bvec_nr_vecs
cciss: fix bug if scsi tape support is disabled
cciss: add support for multi lun tape devices
cciss: change the way we notify scsi midlayer of tape drives
cciss: fix negative logical drive count in procfs
cciss: remove redundant code
cciss: make rebuild_lun_table behave better
cciss: return -EFAULT if copy_from_user() fails
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (23 commits)
V4L/DVB (8617): uvcvideo: don't use stack-based buffers for USB transfers.
V4L/DVB (8616): uvcvideo: Add support for two Bison Electronics webcams
V4L/DVB (8611): Add suspend/resume to pxa_camera driver
V4L/DVB (8610): Add suspend/resume capabilities to soc_camera.
V4L/DVB (8609): media: Clean up platform_driver_unregister() bogosity.
V4L/DVB (8607): cxusb: fix OOPS and broken tuning regression on FusionHDTV Dual Digital 4
V4L/DVB (8605): gspca: Fix of gspca_zc3xx oops - 2.6.27-rc1
V4L/DVB (8604): gspca: Fix of "scheduling while atomic" crash.
V4L/DVB (8602): gspca: Fix small bugs, simplify and cleanup ov519.
V4L/DVB (8582): set mts_firmware for em2882 based Pinnacle Hybrid Pro
V4L/DVB (8574): gspca: Bad bytesperlines of pixelformat in spca505/506/508 and vc023x.
V4L/DVB (8573): gspca: Bad scan of frame in spca505/506/508.
V4L/DVB (8572): gspca: Webcam 0c45:6143 in documentation.
V4L/DVB (8571): gspca: Don't use CONFIG_VIDEO_ADV_DEBUG as a compile option.
V4L/DVB (8569): gspca: Set back the old values of Sonix sn9c120 and cleanup source.
V4L/DVB (8567): gspca: hflip and vflip controls added for ov519 - ov7670 plus init cleanup.
V4L/DVB (8564): fix vino driver build error
V4L/DVB (8563): fix drivers/media/video/arv.c compilation
V4L/DVB (8562): DVB_DRX397XD: remove FW_LOADER select
V4L/DVB (8558): media/video/Kconfig: fix a typo
...
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon: (it87) Support for 16-bit fan reading in it8705 >= rev 0x03
hwmon: (it87) Support for 16-bit fan reading in it8712 >= rev 0x07
hwmon: (hwmon-vid) Add 6-bit vid codes for AMD NPT 0Fh cpus
hwmon: (hwmon-vid) Trivial format multi-line comments per CodingStyle
hwmon: ad7414 driver
hwmon: (thmc50) Add support for critical temperature limits
hwmon: (adm9240) Remove EXPERIMENTAL dependency
hwmon: (w83627hf) Drop reset module parameter
hwmon: (w83627hf) Add pwm_enable sysfs interface
hwmon: (w83791d) Use fan divisor bits from vbat register
hwmon: (f71882fg) Delete needless forward declarations
hwmon: (dme1737) Add support for the SMSC SCH5027
hwmon: (dme1737) Skip detection if forced
hwmon: (dme1737) Cleanups
The it8705 chip supports 16-bit fan tachometers in revisions at least
>= 0x03 (Version G). This patch enables 16-bit fan readings on all
revisions >= 0x03 just like the it8712, it8716, and it8718 chips.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The it8712 chip supports 16-bit fan tachometers in revisions >= 0x07.
Revisions >= 0x08 dropped support for 8-bit fan divisor registers. The
patch enables 16-bit fan readings on all revisions >= 0x07 just like
the it8716 and it8718 chips.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Drop the reset parameter of the w83627hf driver. It seems it wasn't
that useful. It was dropped from the Linux 2.4 version of this driver
back in July 2004.
The only users who have reported that they were still using this
parameter, needed it to switch the chip from automatic fan speed
control back to manual mode. Now that the driver creates pwmN_enable
sysfs files, users will be able to use these files instead, which is
way less agressive.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Dominik Geyer <dominik.geyer@gmx.de>
Update w83791d with fan bits in vbat mon register (7.48 of the
datasheet). This change allows all fans to have a divisor of 128,
and fixes a problem with incorrectly reported fan speeds.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the SCH5027. The differences to the DME1737 are:
- No support for programmable temp offsets
- In auto mode, PWM outputs stay on min value if temp goes below low threshold
and can't be programmed to fully turn off
- Different voltage scaling
- No VID input
Signed-off-by: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch changes way we notify the scsi layer that something has changed
on the SCSI tape side of the driver. The user can now just tell the driver
to rescan a particular controller rather than having to know the SCSI nexus
to echo into the SCSI mid-layer.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Change function name in kernel-doc and add kernel-doc for parameter @index:
Warning(linhead//drivers/media/video/videodev.c:2090): No description found for parameter 'index'
Also change source file name in DocBook/videobook.tmpl to match the new
source file name.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A documentation cleanup patch. With a minor tweak to clarify units for
kbs.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: mark gross <mgross@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These functions have been deprecated for some time now but remained until
all legacy callers could be removed. With a few commits in 2.6.26 this
has happened so now we can remove these deprecated functions.
Signed-off-by: Mark Asselstine <mark.asselstine@windriver.com>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (29 commits)
sh: enable maple_keyb in dreamcast_defconfig.
SH2(A) cache update
nommu: Provide vmalloc_exec().
add addrespace definition for sh2a.
sh: Kill off ARCH_SUPPORTS_AOUT and remnants of a.out support.
sh: define GENERIC_HARDIRQS_NO__DO_IRQ.
sh: define GENERIC_LOCKBREAK.
sh: Save NUMA node data in vmcore for crash dumps.
sh: module_alloc() should be using vmalloc_exec().
sh: Fix up __bug_table handling in module loader.
sh: Add documentation and integrate into docbook build.
sh: Fix up broken kerneldoc comments.
maple: Kill useless private_data pointer.
maple: Clean up maple_driver_register/unregister routines.
input: Clean up maple keyboard driver
maple: allow removal and reinsertion of keyboard driver module
sh: /proc/asids depends on MMU.
arch/sh/boards/mach-se/7343/irq.c: removed duplicated #include
arch/sh/boards/board-ap325rxa.c: removed duplicated #include
sh/boards/Makefile typo fix
...
This adds some preliminary docbook bits for SH, tying in to the few
interfaces that are exposed and that have adequate kerneldoc comments.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
from include/asm-powerpc. This is the result of a
mkdir arch/powerpc/include/asm
git mv include/asm-powerpc/* arch/powerpc/include/asm
Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly. Of the latter only
one was outside the arch code and it is a driver only built for powerpc.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I asked legal about the licensing of ftrace.txt, and they told me that,
unless the Documentation directory is specifically set up to handle non
GPL licenses (which it does not appear to be), then it would be best to
put ftrace.txt under the GPL.
This patch adds a dual license to ftrace.txt such that it is under both
the FDL and the GPL.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
[PATCH] ocfs2: Release mutex in error handling code
[PATCH] ocfs2: Fix oops when racing files truncates with writes into an mmap region
[PATCH 2/2] ocfs2: Fix race between mount and recovery
[PATCH 1/2] ocfs2: Add counter in struct ocfs2_dinode to track journal replays
[PATCH] configfs: Convenience macros for attribute definition.
[PATCH] configfs: Pin configfs subsystems separately from new config_items.
[PATCH] configfs: Fix open directory making rmdir() fail
[PATCH] configfs: Lock new directory inodes before removing on cleanup after failure
[PATCH] configfs: Prevent userspace from creating new entries under attaching directories
[PATCH] configfs: Fix failing symlink() making rmdir() fail
[PATCH] configfs: Fix symlink() to a removing item
[PATCH] configfs: Include linux/err.h in linux/configfs.h
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kgdb: fix gdb serial thread queries
kgdb: fix kgdb_validate_break_address to perform a mem write
kgdb: remove the requirement for CONFIG_FRAME_POINTER
* git://git.infradead.org/battery-2.6:
power_supply: Sharp SL-6000 (tosa) batteries support
power_supply: fix up CHARGE_COUNTER output to be more precise
power_supply: add CHARGE_COUNTER property and olpc_battery support for it
power_supply: bump EC version check that we refuse to run with in olpc_battery
power_supply: cleanup of the OLPC battery driver
power_supply: add eeprom dump file to olpc_battery's sysfs
power_supply: Support serial number in olpc_battery
A regression to the kgdb core was found in the case of using the
CONFIG_DEBUG_RODATA kernel option. When this option is on, a breakpoint
cannot be written into any readonly memory page. When an external
debugger requests a breakpoint to get set, the
kgdb_validate_break_address() was only checking to see if the address
to place the breakpoint was readable and lacked a write check.
This patch changes the validate routine to try reading (via the
breakpoint set request) and also to try immediately writing the break
point. If either fails, an error is correctly returned and the
debugger behaves correctly. Then an end user can make the
descision to use hardware breakpoints.
Also update the documentation to reflect that using
CONFIG_DEBUG_RODATA will inhibit the use of software breakpoints.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
There is no technical reason that the kgdb core requires frame
pointers. It is up to the end user of KGDB to decide if they need
them or not.
[ anemo@mba.ocn.ne.jp: removed frame pointers on mips ]
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Drop a lot of useless register defines, conversion macros, data structure
members and update code. All these register values were read from the
device but nothing is done out of them, so this is all dead code in
practice.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch adds a module load parameter to enable probing of
non-standard LPC addresses 0x162e and 0x164e when scanning for supported
ISA chips.
Signed-Off-By: Juerg Haefliger <juergh at gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Sysfs has the _ATTR() and _ATTR_RO() macros to make defining extended
form attributes easier. configfs should have something similiar.
- _CONFIGFS_ATTR() and _CONFIGFS_ATTR_RO() are the counterparts to the
sysfs macros.
- CONFIGFS_ATTR_STRUCT() creates the extended form attribute structure.
- CONFIGFS_ATTR_OPS() defines the show_attribute()/store_attribute()
operations that call the show()/store() operations of the extended
form configfs_attributes.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Minor /dev/hpet updates and bugfixes:
* Remove dead code, mostly remnants of an incomplete/unusable
kernel interface ... noted when addressing "sparse" warnings:
+ hpet_unregister() and a routine it calls
+ hpet_task and all references, including hpet_task_lock
+ hpet_data.hd_flags (and HPET_DATA_PLATFORM)
* Correct and improve boot message:
+ displays *counter* (shared between comparators) bit width,
not *timer* bit widths (which are often mixed)
+ relabel "timers" as "comparators"; this is less confusing,
they are not independent like normal timers are (sigh)
+ display MHz not Hz; it's never less than 10 MHz.
* Tighten and correct the userspace interface code
+ don't accidentally program comparators in 64-bit mode using
32-bit values ... always force comparators into 32-bit mode
+ provide the correct bit definition flagging comparators with
periodic capability ... the ABI is unchanged
* Update Documentation/hpet.txt
+ be more correct and current
+ expand description a bit
+ don't mention that now-gone kernel interface
Plus, add a FIXME comment for something that could cause big trouble
on systems with more capable HPETs than at least Intel seems to ship.
It seems that few folk use this userspace interface; it's not very
usable given the general lack of HPET IRQ routing. I'm told that
the only real point of it any more is to mmap for fast timestamps;
IMO that's handled better through the gettimeofday() vsyscall.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Lockless get_user_pages_fast() for 64-bit (v3)
powerpc: Don't use the wrong thread_struct for ptrace get/set VSX regs
powerpc: Fix ptrace buffer size for VSX
powerpc: Correctly hookup PTRACE_GET/SETVSRREGS for 32 bit processes
ide/powermac: Fix use of uninitialized pointer on media-bay
powerpc: Allow non-hcall return values for lparcfg writes
ipmi/powerpc: Use linux/of_{device,platform}.h instead of asm
powerpc/fsl: proliferate simple-bus compatibility to soc nodes
Documentation: remove old sbc8260 board specific information
cpm2: Rework baud rate generators configuration to support external clocks.
powerpc: rtc_cmos_setup: assign interrupts only if there is i8259 PIC
cpm_uart: Add generic clock API support to set baudrates
cpm_uart: Modem control lines support
powerpc: implement GPIO LIB API on CPM1 Freescale SoC.
cpm2: Implement GPIO LIB API on CPM2 Freescale SoC.
powerpc: Fix 8xx build failure
powerpc: clean up the Book-E HW watchpoint support
This adds overview documentation describing the regulator framework and
nomenclature used in the interface specific documentation and code.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
While the rfkill class does work with just get_state(), it doesn't work
well on devices that are subject to external events that cause rfkill state
changes.
Document that rfkill_force_state() is required in those cases.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: turn Waker into a thread, not a process
lguest: Enlarge virtio rings
lguest: Use GSO/IFF_VNET_HDR extensions on tun/tap
lguest: Remove 'network: no dma buffer!' warning
lguest: Adaptive timeout
lguest: Tell Guest net not to notify us on every packet xmit
lguest: net block unneeded receive queue update notifications
lguest: wrap last_avail accesses.
lguest: use cpu capability accessors
lguest: virtio-rng support
lguest: Support assigning a MAC address
lguest: Don't leak /dev/zero fd
lguest: fix verbose printing of device features.
lguest: fix switcher_page leak on unload
lguest: Guest int3 fix
lguest: set max_pfn_mapped, growl loudly at Yinghai Lu
lguest uses a Waker process to break it out of the kernel (ie.
actually running the guest) when file descriptor needs attention.
Changing this from a process to a thread somewhat simplifies things:
it can directly access the fd_set of things to watch. More
importantly, it means that the Waker can see Guest memory correctly,
so /dev/vring file descriptors will work as anticipated (the
alternative is to actually mmap MAP_SHARED, but you can't do that with
/dev/zero).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Since the correct timeout value varies, use a heuristic which adjusts
the timeout depending on how many packets we've seen. This gives
slightly worse results, but doesn't need tweaking when GSO is
introduced.
500 usec 19.1887 xmit 561141 recv 1 timeout 559657
Dynamic (278) 20.1974 xmit 214510 recv 5 timeout 214491 usec 278
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio_ring has the ability to suppress notifications. This prevents
a guest exit for every packet, but we need to set a timer on packet
receipt to re-check if there were any remaining packets.
Here are the times for 1G TCP Guest->Host with different timeout
settings (it matters because the TCP window doesn't grow big enough to
fill the entire buffer):
Timeout value Seconds Xmit/Recv/Timeout
None (before) 25.3784 xmit 7750233 recv 1
2500 usec 62.5119 xmit 207020 recv 2 timeout 207020
1000 usec 34.5379 xmit 207003 recv 2 timeout 207003
750 usec 29.2305 xmit 207002 recv 1 timeout 207002
500 usec 19.1887 xmit 561141 recv 1 timeout 559657
250 usec 20.0465 xmit 214128 recv 2 timeout 214110
100 usec 19.2583 xmit 561621 recv 1 timeout 560153
(Note that these values are sensitive to the GSO patches which come
later, and probably other traffic-related variables, so take with a
large grain of salt).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
To simplify the transition to when we publish indices in the ring
(and make shuffling my patch queue easier), wrap them in a lg_last_avail()
macro.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This is a simple patch to add support for the virtio "hardware random
generator" to lguest. It gets about 1.2 MB/sec reading from /dev/hwrng
in the guest.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
If you've got a nice DHCP configuration which maps MAC
addresses to specific IP addresses, then you're going to
want to start your guest with one of those MAC addresses.
Also, in Fedora, we have persistent network interface naming
based on the MAC address, so with randomly assigned
addresses you're soon going to hit eth13. Who knows what
will happen then!
Allow assigning a MAC address to the network interface with
e.g.
--tunnet=bridge:eth0:00:FF:95:6B:DA:3D
or:
--tunnet=192.168.121.1:00:FF:95:6B:DA:3D
which is pretty unintelligable, but ...
(includes Rusty's minor rework)
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This file contains 8 yr. old board specific information that was for
the now gone ppc implementation, and it pre-dates widespread u-boot
support. Any of the technical details of the board memory map would be
more appropriately captured in a dts if I revive it as powerpc anyway.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add git pull command info and diffstat summary info so that we don't
have to search email archives for it repeatedly.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces the get_mctrl/set_mctrl stubs with modem control line
read/write access through the GPIO lib.
Available modem control lines are described in the device tree using GPIO
bindings. The driver expect a GPIO pin for each of the CTS, RTS, DCD, DSR,
DTR and RI signals. Unused control lines can be left out.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move mtrr.txt to the Documentation/x86/ subdirectory.
Add 00-INDEX to the Documentation/x86/ subdirectory.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a document describing how i2c clients on Linux 2.6 can be
moved from the old to the new driver model.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
- New supported IDs for analog models
(Based on Markus Rechberger <mrechberger@gmail.com> version of em28xx driver)
- Validation field for new em28xx boards.
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
[mchehab@infradead.org: Need to fix some merge conflicts]
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-next: (25 commits)
setlocalversion: do not describe if there is nothing to describe
kconfig: fix typos: "Suport" -> "Support"
kconfig: make defconfig is no longer chatty
kconfig: make oldconfig is now less chatty
kconfig: speed up all*config + randconfig
kconfig: set all new symbols automatically
kconfig: add diffconfig utility
kbuild: remove Module.markers during mrproper
kbuild: sparse needs CF not CHECKFLAGS
kernel-doc: handle/strip __init
vmlinux.lds: move __attribute__((__cold__)) functions back into final .text section
init: fix URL of "The GNU Accounting Utilities"
kbuild: add arch/$ARCH/include to search path
kbuild: asm symlink support for arch/$ARCH/include
kbuild: support arch/$ARCH/include for tags, cscope
kbuild: prepare headers_* for arch/$ARCH/include
kbuild: install all headers when arch is changed
kbuild: make clean removes *.o.* as well
kbuild: optimize headers_* targets
kbuild: only one call for include/ in make headers_*
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: Allow to force model to intel-mac-v3 in snd_hda_intel (sigmatel).
ALSA: cs4232: fix crash during chip PNP detection
ALSA: hda - Add automatic model setting for the Acer Aspire 5920G laptop
ALSA: make snd_ac97_add_vmaster() static
ALSA: sound/pci/azt3328.h: no variables for enums
ALSA: soc - wm9712 mono mixer
ALSA: hda - Add support of ASUS Eeepc P90*
ALSA: opti9xx: no isapnp param for !CONFIG_PNP
ALSA: opti93x - Fix NULL dereference
ALSA: hda - Added support for Asus V1Sn
ALSA: ASoC: Factor PGA DAPM handling into main
ALSA: ASoC: Refactor DAPM event handler
ALSA: ALSA: ens1370: communicate PCI device to AC97
ALSA: ens1370: SRC stands for Sample Rate Converter
ALSA: hda - Align BDL position adjustment parameter
ALSA: Au1xpsc: psc not disabled when TX is idle
ALSA: add TriTech 28023 AC97 codec ID and Wolfson 9701 name.
IRQT_* and __IRQT_* were obsoleted long ago by patch [3692/1].
Remove them completely. Sed script for the reference:
s/__IRQT_RISEDGE/IRQ_TYPE_EDGE_RISING/g
s/__IRQT_FALEDGE/IRQ_TYPE_EDGE_FALLING/g
s/__IRQT_LOWLVL/IRQ_TYPE_LEVEL_LOW/g
s/__IRQT_HIGHLVL/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_RISING/IRQ_TYPE_EDGE_RISING/g
s/IRQT_FALLING/IRQ_TYPE_EDGE_FALLING/g
s/IRQT_BOTHEDGE/IRQ_TYPE_EDGE_BOTH/g
s/IRQT_LOW/IRQ_TYPE_LEVEL_LOW/g
s/IRQT_HIGH/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_PROBE/IRQ_TYPE_PROBE/g
s/IRQT_NOEDGE/IRQ_TYPE_NONE/g
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, even if you pass model=intel-mac-v3 as a module parameter to
snd_hda_intel, the function patch_stac922x (patch_sigmatel.c) will still
try to auto-detect the model type. This is a problem on my MacBook Pro 1st
generation, which needs intel-mac-v3, but sometimes incorrectly reports
0x00000100 as subsystem id, which causes the switch in patch_stac922x to
select intel-mac-v4.
To fix this, I added a new model called intel-mac-auto, so in case no
module parameter is passed, and an Intel Mac board is detected, the
model will be automatically detected, while no detection will be done
if the model is forced to intel-mac-v3.
This problem has been around for quite a while, and I used to fix it
by moving the case statement for 0x00000100 in patch_stac922x so that
intel-mac-v3 is chosen.
Another way to fix the problem would be to check if a module parameter
was set directly in patch_stac922x, using something like this:
if (spec->board_config == STAC_INTEL_MAC_V3 &&
!codec->bus->modelname) {
But I think it is less elegant (if you prefer that way, I can prepare a
patch).
Signed-off-by: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
mISDN is a new modular ISDN driver, in the long term it should replace
the old I4L driver architecture for passiv ISDN cards.
Signed-off-by: Karsten Keil <kkeil@suse.de>
These patches add the Optimized MPEG Filesystem, a proprietary filesystem used
by the embedded devices Rio Karma and ReplayTV, which are no longer
manufactured. This filesystem module enables people to access files on these
devices.
This patch:
OMFS is a proprietary filesystem created for the ReplayTV and also used by the
Rio Karma. It uses hash tables with unordered, unbounded lists in each bucket
for directories, extents for data blocks, 64-bit addressing for blocks, with
up to 8K blocks (only 2K of a given block is ever used for metadata, so the FS
still works with 4K pages).
Document the filesystem usage and structures.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allows one to create and use a channel with no associated files. Files
can be initialized later. This is useful in scenarios such as logging in
early code, before VFS is up. Therefore, such channels can be created and
used as soon as kmem_cache_init() completed.
This is needed by kmemtrace to do tracing in early kernel code.
[kosaki.motohiro@jp.fujitsu.com: build fix]
Signed-off-by: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Cc: Tom Zanussi <tzanussi@gmail.com>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER
architecture does:
This enables us to cleanly fix the Calgary IOMMU issue that some devices
are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423).
I think that per-device dma_mapping_ops support would be also helpful for
KVM people to support PCI passthrough but Andi thinks that this makes it
difficult to support the PCI passthrough (see the above thread). So I
CC'ed this to KVM camp. Comments are appreciated.
A pointer to dma_mapping_ops to struct dev_archdata is added. If the
pointer is non NULL, DMA operations in asm/dma-mapping.h use it. If it's
NULL, the system-wide dma_ops pointer is used as before.
If it's useful for KVM people, I plan to implement a mechanism to register
a hook called when a new pci (or dma capable) device is created (it works
with hot plugging). It enables IOMMUs to set up an appropriate
dma_mapping_ops per device.
The major obstacle is that dma_mapping_error doesn't take a pointer to the
device unlike other DMA operations. So x86 can't have dma_mapping_ops per
device. Note all the POWER IOMMUs use the same dma_mapping_error function
so this is not a problem for POWER but x86 IOMMUs use different
dma_mapping_error functions.
The first patch adds the device argument to dma_mapping_error. The patch
is trivial but large since it touches lots of drivers and dma-mapping.h in
all the architecture.
This patch:
dma_mapping_error() doesn't take a pointer to the device unlike other DMA
operations. So we can't have dma_mapping_ops per device.
Note that POWER already has dma_mapping_ops per device but all the POWER
IOMMUs use the same dma_mapping_error function. x86 IOMMUs use device
argument.
[akpm@linux-foundation.org: fix sge]
[akpm@linux-foundation.org: fix svc_rdma]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix bnx2x]
[akpm@linux-foundation.org: fix s2io]
[akpm@linux-foundation.org: fix pasemi_mac]
[akpm@linux-foundation.org: fix sdhci]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix sparc]
[akpm@linux-foundation.org: fix ibmvscsi]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
em28xx-cards.c
em28xx-dvb.c
em28xx.h
- Add support for the ATI TV Wonder HD 600, based on a 94 email exchange and
USB traces provided by Ronnie Bailey
Thanks to Ronnie Bailey <purevw@wtxs.net> for testing the changes
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
based on work from Eric, and add some timeout so don't dead loop when debug
device is not installed
v2: fix checkpatch warning
v3: move ehci struct def to linux/usrb/ehci_def.h from host/ehci.h
also add CONFIG_EARLY_PRINTK_DBGP to disable it by default
v4: address comments from Ingo, seperate ehci reg def moving to another patch
also add auto detect port that connect to debug device for Nvidia
southbridge
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: "Arjan van de Ven" <arjan@infradead.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "Greg KH" <greg@kroah.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Documentation/sparse.txt tells to use:
make C=2 CHECKFLAGS="-D__CHECK_ENDIAN__"
However, this still doesn't enable endian checks. The correct syntax is:
make C=2 CF="-D__CHECK_ENDIAN__"
This documentation bug was introduced by the following commit:
commit 1c7bafe720
Author: Robert P. J. Day <rpjday@mindspring.com>
Date: Wed Sep 13 07:57:50 2006 -0400
kbuild: clarify "make C=" build option
Clarify the use of "make C=" in the top-level Makefile, and fix a
typo in the Documentation file.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This `typo' was not a typo, as `CF' had been introduced much earlier, by:
commit 7b49bb9aff
Author: viro@ZenIV.linux.org.uk <viro@ZenIV.linux.org.uk>
Date: Fri Sep 9 21:14:35 2005 +0100
[PATCH] kbuild: CF=<arguments> passes arguments to sparse
Allows to add to sparse arguments without mutilating makefiles - just
pass CF=<arguments> and they will be added to CHECKFLAGS.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (34 commits)
powerpc: Wireup new syscalls
Move update_mmu_cache() declaration from tlbflush.h to pgtable.h
powerpc/pseries: Remove kmalloc call in handling writes to lparcfg
powerpc/pseries: Update arch vector to indicate support for CMO
ibmvfc: Add support for collaborative memory overcommit
ibmvscsi: driver enablement for CMO
ibmveth: enable driver for CMO
ibmveth: Automatically enable larger rx buffer pools for larger mtu
powerpc/pseries: Verify CMO memory entitlement updates with virtual I/O
powerpc/pseries: vio bus support for CMO
powerpc/pseries: iommu enablement for CMO
powerpc/pseries: Add CMO paging statistics
powerpc/pseries: Add collaborative memory manager
powerpc/pseries: Utilities to set firmware page state
powerpc/pseries: Enable CMO feature during platform setup
powerpc/pseries: Split retrieval of processor entitlement data into a helper routine
powerpc/pseries: Add memory entitlement capabilities to /proc/ppc64/lparcfg
powerpc/pseries: Split processor entitlement retrieval and gathering to helper routines
powerpc/pseries: Remove extraneous error reporting for hcall failures in lparcfg
powerpc: Fix compile error with binutils 2.15
...
Fixed up conflict in arch/powerpc/platforms/52xx/Kconfig manually.
/sys/devices/system/edac/mc has a few files which are duplicated in
/sys/module/edac_core/parameters. Now that all the functionality is
duplicated between these two locations, we remove the former kobject
attributes and update the documentation.
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update document and make getdelays.c show delay accounting for memory reclaim.
For making a distinction between "swapping in pages" and "memory reclaim"
in getdelays.c, MEM is changed to SWAP.
Signed-off-by: Keika Kobayashi <kobayashi.kk@ncos.nec.co.jp>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add members for memory reclaim delay to taskstats, and accumulate them in
__delayacct_add_tsk() .
Signed-off-by: Keika Kobayashi <kobayashi.kk@ncos.nec.co.jp>
Cc: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It seems to me that it was a mistake marking this function as deprecated
and scheduling it for removal, rather than resolutely removing it after
the last caller's death.
Anyway - better late, then never.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update Documentation/moxa-smartio to the later document from the mxser
package.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Having trailing entities in a revision numer seems pretty pointless
to me. More so, it's causing me pains, so just drop them since no other
guide is doing this.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds functionality to the gpio-lib subsystem to make it
possible to enable the gpio-lib code even if the architecture code didn't
request to get it built in.
The archtitecture code does still need to implement the gpiolib accessor
functions in its asm/gpio.h file. This patch adds the implementations for
x86 and PPC.
With these changes it is possible to run generic GPIO expansion cards on
every architecture that implements the trivial wrapper functions. Support
for more architectures can easily be added.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds the bt8xxgpio driver. The purpose of the bt8xxgpio driver is to
export all of the 24 GPIO pins available on Brooktree 8xx chips to the
kernel GPIO infrastructure.
This makes it possible to use a physically modified BT8xx card as
cheap digital GPIO card.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a simple sysfs interface for GPIOs.
/sys/class/gpio
/export ... asks the kernel to export a GPIO to userspace
/unexport ... to return a GPIO to the kernel
/gpioN ... for each exported GPIO #N
/value ... always readable, writes fail for input GPIOs
/direction ... r/w as: in, out (default low); write high, low
/gpiochipN ... for each gpiochip; #N is its first GPIO
/base ... (r/o) same as N
/label ... (r/o) descriptive, not necessarily unique
/ngpio ... (r/o) number of GPIOs; numbered N .. N+(ngpio - 1)
GPIOs claimed by kernel code may be exported by its owner using a new
gpio_export() call, which should be most useful for driver debugging.
Such exports may optionally be done without a "direction" attribute.
Userspace may ask to take over a GPIO by writing to a sysfs control file,
helping to cope with incomplete board support or other "one-off"
requirements that don't merit full kernel support:
echo 23 > /sys/class/gpio/export
... will gpio_request(23, "sysfs") and gpio_export(23);
use /sys/class/gpio/gpio-23/direction to (re)configure it,
when that GPIO can be used as both input and output.
echo 23 > /sys/class/gpio/unexport
... will gpio_free(23), when it was exported as above
The extra D-space footprint is a few hundred bytes, except for the sysfs
resources associated with each exported GPIO. The additional I-space
footprint is about two thirds of the current size of gpiolib (!). Since
no /dev node creation is involved, no "udev" support is needed.
Related changes:
* This adds a device pointer to "struct gpio_chip". When GPIO
providers initialize that, sysfs gpio class devices become children of
that device instead of being "virtual" devices.
* The (few) gpio_chip providers which have such a device node have
been updated.
* Some gpio_chip drivers also needed to update their module "owner"
field ... for which missing kerneldoc was added.
* Some gpio_chips don't support input GPIOs. Those GPIOs are now
flagged appropriately when the chip is registered.
Based on previous patches, and discussion both on and off LKML.
A Documentation/ABI/testing/sysfs-gpio update is ready to submit once this
merges to mainline.
[akpm@linux-foundation.org: a few maintenance build fixes]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Describe a setup that integrates better with Emacs' cc-mode and also fixes
up the alignment of continuation lines to really only use tabs.
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some bits were missed when the tipar driver was removed.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In many cases, especially in networking, it can be beneficial to know at
compile time whether the architecture can do unaligned accesses efficiently.
This patch introduces a new Kconfig symbol
HAVE_EFFICIENT_UNALIGNED_ACCESS
for that purpose and adds it to the powerpc and x86 architectures. Also add
some documentation about alignment and networking, and especially one intended
use of this symbol.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Ingo Molnar <mingo@elte.hu> [x86 architecture part]
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-acpi-2.6:
acpi: fix crash in core ACPI code, triggered by CONFIG_ACPI_PCI_SLOT=y
ACPI: thinkpad-acpi: don't misdetect in get_thinkpad_model_data() on -ENOMEM
ACPI: thinkpad-acpi: bump up version to 0.21
ACPI: thinkpad-acpi: add bluetooth and WWAN rfkill support
ACPI: thinkpad-acpi: WLSW overrides other rfkill switches
ACPI: thinkpad-acpi: prepare for bluetooth and wwan rfkill support
ACPI: thinkpad-acpi: consolidate wlsw notification function
ACPI: thinkpad-acpi: minor refactor on radio switch init
Revert "ACPI: don't walk tables if ACPI was disabled"
Revert "dock: bay: Don't call acpi_walk_namespace() when ACPI is disabled."
Revert "Fix FADT parsing"
ACPI : Set FAN device to correct state in boot phase
ACPI: Ignore _BQC object when registering backlight device
ACPI: stop complaints about interrupt link End Tags and blank IRQ descriptors
* 'semaphore' of git://git.kernel.org/pub/scm/linux/kernel/git/willy/misc:
Remove __DECLARE_SEMAPHORE_GENERIC
Remove asm/semaphore.h
Remove use of asm/semaphore.h
Add missing semaphore.h includes
Remove mention of semaphores from kernel-locking
Make the tridentfb documentation closer to current state of the tridentfb
driver. Fix also some formatting.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ACPI defines a hardware signature. BIOS calculates the signature according to
hardware configure and if hardware changes while hibernated, the signature
will change. In that case, S4 resume should fail.
Still, there may be systems on which this mechanism does not work correctly,
so it is better to provide a workaround for them. For this reason, add a new
switch to the acpi_sleep= command line argument allowing one to disable
hardware signature checking.
[shaohua.li@intel.com: build fix]
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <Valdis.Kletnieks@vt.edu>
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove some obsolete PM documentation.
The majority of contents of Documentation/power/pm.txt are
outdated. Remove the outdated parts of this file and move the rest
to Documentation/power/apm-acpi.txt . Update the index in
Documentation/power/ as appropriate.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Boot-time test for system suspend states (STR or standby). The generic
RTC framework triggers wakeup alarms, which are used to exit those states.
- Measures some aspects of suspend time ... this uses "jiffies" until
someone converts it to use a timebase that works properly even while
timer IRQs are disabled.
- Triggered by a command line parameter. By default nothing even
vaguely troublesome will happen, but "test_suspend=mem" will give
you a brief STR test during system boot. (Or you may need to use
"test_suspend=standby" instead, if your hardware needs that.)
This isn't without problems. It fires early enough during boot that for
example both PCMCIA and MMC stacks have misbehaved. The workaround in
those cases was to boot without such media cards inserted.
[matthltc@us.ibm.com: fix compile failure in boot time suspend selftest]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Pavel Machek <pavel@suse.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
