In the single_cmd mode, the hardware cannot store the multiple replies
like on RIRB, thus each verb has to sync and wait for the response no
matter whether the return value is needed or not. Otherwise it may
result in a wrong return value from the previous verb.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Unsigned variables should use `%u' rather than `%d'.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A docking mic control is shown by default. The Compaq Presario
CQ60 laptop has no docking connector, so designate it as a
CXT5051_HP model.
This makes the phantom mixer slider disappear.
Signed-off-by: Tony Vroon <tony@linx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The function signature for spin_event_timeout() has changed in version V9.
Adjust the mpc5200 AC97 driver to use the new function.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The effect of symmetric_constraints should provide a standard way to
enforce the use of the same sample rate for both directions.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Timur Tabi <timur@freescale.com>
Kernel 2.6.18 broke the MotU Fastlane, which uses duplicate endpoint
numbers in a manner that is not only illegal but also confuses the
kernel's endpoint descriptor caching mechanism. To work around this, we
have to add a separate usb_set_interface() call to guide the USB core to
the correct descriptors.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-and-tested-by: David Fries <david@fries.net>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCM hw_ptr jiffies check results sometimes in problems when a
hardware doesn't give smooth hw_ptr updates. So far, au88x0 and some
other drivers appear not working due to this strict check.
However, this check is a nice debug tool, and the capability should be
still kept.
Hence, we disable this check now as default unless the user enables it
by setting the xrun_debug mode to the specific stream via a proc file.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The hw_ptr_jiffies has to be reset properly to avoid the invalid
check of jiffies delta in snd_pcm_update_hw_ptr*() functions.
Especailly this patch fixes the bogus jiffies check after the puase
and resume.
This patch is a modified version of the original patch by Jaroslav.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These drivers use spin_event_timeout() which is only present in the
PowerPC tree at present and which is undergoing some API revisions
so temporarily mark them as BROKEN until these issues are sorted
out.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
I've implemented retries for when the AC97 hardware doesn't reset on
first try. About 10% of the time both the Efika and pcm030 AC97 codecs
don't reset on first try and need to be poked multiple times. Failure
is indicated by not having the link clock start ticking. Every once in
a while even five pokes won't get the link started and I have to power
cycle.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rewrite the mpc5200 audio DMA code to support both I2S and AC97.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Add missing check of pin vref 50 and others in Realtek codecs
ALSA: hda - Add 5stack-no-fp model for STAC927x
ALSA: hda - Add forced codec-slots for ASUS W5Fm
This patch adds a debug mode to make the codec communication
synchronous. Define SND_HDA_SUPPORT_SYNC_WRITE in hda_codec.c,
and the call of snd_hda_codec_write*() will become synchronous,
i.e. wait for the reply from the codec at each time issuing a verb.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the single_cmd mode, the current driver code doesn't do any update
for RIRB just for any safety reason. But, actually the RIRB and
single_cmd mode don't conflict. Unsolicited events can be delivered
even while using the single_cmd mode.
This patch allows the handling of unsolicited events with single_cmd
mode, just always checking RIRB independent from single_cmd flag.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current code doesn't handle the multiple gameports properly,
and uses unnecessary global static variables to store the data.
This patch changes the probe / remove routines to use the driver
data assigned to the dedicated pci device, and adds the support of
multiple devices.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A code clean up, coding style fixes.
The firmware loading routine is split to an own function to improve
the readability.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a codec communication error occurs, the CORB/RIRB counters should
be reset first before re-issuing the verb. Simply call azx_free_cmd_io()
and azx_init_cmd_io() to achieve that.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add DAPM switch for HeadsetL/R mute. Since all bits are are needed
for the HFL/R pop removal to work the switch is using the SW_SHADOW
no HW register for the HandsfreeL/R mute.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Shadow, non HW register for dealing with the HandsfreeL/R
muting.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move the HandsfreeL/R (IHFL/R) pop removal code from the DAPM_MUX_E
to a more appropriate DAPM_PGA_E widget.
Also fix the power-up sequence to match with the TRM.
The power-down sequence is not described in the TRM, so do it
in a way, which seams like the correct sequence.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for the Asus Xonar Essence ST and its daughterboard.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Xonar HDAV1.3 has a digital input jack, so enable the corresponding
device.
This is not related to the HDMI stuff, which stays unsupported.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add another PCI ID for a second revision of the Xonar DX.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a PCM stream is closed, flush the corresponding DMA channel.
Otherwise, the DMA controller would continue to output the last sample
which would result in a DC offset on the output.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some Realtek codecs like ALC861 seem to support only VREF50 while the
current driver assumes it's only VREF80. Check other VREF bits to set
the correct value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rename the functions in the mpc5200 DMA file from i2s based names to dma
ones to reflect the file they are in.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Basic split of mpc5200 DMA code out from i2s into a standalone file.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The recent fix for the headphone volume control on IDT/STAC codecs
resulted in the removal of invalid "Side" volume eventually. But,
if the front panel doesn't exist, this setup could be regarded as a
sort of regression, as reported in kernel bug #13250.
Now as a workaround, a new model 5stack-no-fp is added so that the user
without the front panel can choose this one explicitly.
Reference: bko#13250
http://bugzilla.kernel.org/show_bug.cgi?id=13250
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS W5Fm needs the fixed codec-slots to probe to override the BIOS
problem like W5F.
Tested-by: Alp Kılıç <kilic.alp@gmail.com>
Signed-off-by: Ozan Çağlayan <ozan@pardus.org.tr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fairly minor issues:
- Don't register the DAIs, it's not required for AC97 devices.
- Make unexported functions static.
- Wrap some excessively long lines.
- Undo tab/space breakage.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure that we always set a new sysclk when using the FLL in master mode
and pick out the correct value for the sample rate in hw_params().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ALSA sound/core/control.c:232: Control name 'Sigmatel Surround Phase
Inversion Playback Switch' truncated to 'Sigmatel Surround Phase
Inversion Playback ' bootup message by omitting weird Sigmatel prefix
in this case; also fix up the related ca0106 mixer control removal
part by using identical naming there.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The WM9081 is designed to provide high power output at low distortion
levels in space-constrained portable applications.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Give unique stream names for the two playback streams so
DAPM can figure out which codec_dai is in use.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With this patch the initial headset pop-removal related values are
configured for the twl4030 codec (ramp delay and sysclk).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
twl4030_setup_data structure can be passed from platform drivers to
the codec via the snd_soc_device->codec_data pointer.
Currently the setup data has support for the Headset pop-removal
related configuration, which differs from board to board.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The second argument of the probe method points to the amba_id
structure, so it's better passed with the correct type. None of the
current in-tree drivers uses the pointer, so they have only been
checked for a clean compile.
Change suggested by Russell King.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The commit 5a641bcd63 changed the
printk format to '%lu', but the value passed seems to be dependent
on the architecture. On x86-64, I got a new warning now because an
int value is passed actaully.
As a workaround, just cast the value always to unsigned long.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ctxfi driver requires explicitly the 4k page size, and gives a
build error on architectures with non-4k pages.
As a workaround, just add the kconfig dependency on X86, which is
the only architecture ever tested.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds SND_SOC_DAPM_PGA_E to the headset path, which handles
the headset ramp up and down sequences needed for the pop noise
removal.
With this patch the order of the internal components in the twl4030
codec is turned on and off in a correct order.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Tested-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Tested-by: Jarkko Nikula <jhnikula@gmail.com>
Tested-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Restructuring the twl4030 codec's DAPM routing to be able to handle the power
sequences correctly.
The twl4030 codec internal implementation have this order:
DAC -> Analog PGA -> Mixer/Mux
While the ASoC framework expects the following order:
DAC -> Mixer -> Analog PGA
This patch moves the Analog PGA handling from SND_SOC_DAPM_PGA to _MIXER and
adds two levels of mixer to handle the digital and analog loopback
functionality.
Now the analog loopback does not powers on any of the DACs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Tested-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Tested-by: Jarkko Nikula <jhnikula@gmail.com>
Tested-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the integrated ACLC of the TXx9 family.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The digital beep tone is calculated in two different ways depending
on the codec chip. The standard one is using a divider, and another
one is a linear tone for IDT/STAC codecs. Currently, only the
latter type is used for all codecs, which resulted in a wrong tone
pitch.
This patch adds the calculation of the standard HD-audio type.
Also clean-up the fields in hda_beep struct.
Reference: bko#13162
http://bugzilla.kernel.org/show_bug.cgi?id=13162
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add proper prefix to each kernel message in hda_intel.c.
Also, avoid the unneeded prefix when CONFIG_SND_VERBOSE_PRINTK is used
together with snd_print*().
Reference: bko#13207
http://bugzilla.kernel.org/show_bug.cgi?id=13207
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Connect twl4030 voice DAI to McBSP3 in sdp3430 machine driver.
Voice DAI init function enables corresponding interface by
writting directly to VOICE_IF codec register.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujflausi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a control for selecting the codec operation mode. TWL4030 codec
has two modes:
- Option 1. Audio only (4 audio DACs)
- Option 2. Voice/Audio (2 audio DACs and voice ADC/DAC)
Control is restricted when a stream is ongoing, since codec's
operation mode cannot be changed on-the-fly.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujflausi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
AUXR is selected by bit 2 and not by bit 1 in the ANAMICR register.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move all the gpio functions out of <mach/hardware.h> as
this file is for defining the generic IO base addresses
for the kernel IO calls.
Make a new header <mach/gpio-fns.h> to take this and
include it via the chain from <linux/gpio.h> which is
what most of these files should be using (and will be
changed as soon as possible).
Note, this does make minor changes to some drivers but
should not mess up any pending merges.
CC: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Rather than managing the bias level of the system based on if there is
an active audio stream manage it based on there being an active DAPM
widget. This simplifies the code a little, moving the power handling
into one place, and improves audio performance for bypass paths when no
playbacks or captures are active.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DAPM has always applied any changes to the power state of widgets as soon
as it has determined that they are required. Instead of doing this store
all the changes that are required on lists of widgets to power up and
down, then iterate over those lists and apply the changes. This changes
the sequence in which changes are implemented, doing all power downs
before power ups and always using the up/down sequences (previously they
were only used when changes were due to DAC/ADC power events). The error
handling is also changed so that we continue attempting to power widgets
if some changes fail.
The main benefit of this is to allow future changes to do optimisations
over the whole power sequence and to reduce the number of walks of the
widget graph required to check the power status of widgets.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for MacBook 3,1 sound by adding a model new
"mb31" with the appropriate init verbs, mixers and channel modes to
the ALC883 configuration. patch_alc882() and patch_alc883() are
modified to handle the MacBook 3,1 sound-chip (Realtek ALC889A)
correctly.
Signed-off-by: Torben Schulz <public@letorbi.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCI entries of Creative with HD-audio class can be the devices
with emu20k1/emu20k2 chips. These are supported better by snd-ctxfi
driver. With that driver, the device will mutate from HD-audio to
its native class.
This patch adds a simple ifdef to avoid the conflict of device probe
between snd-hda-intel and snd-ctxfi drivers. 1102:0009 seems still
OK to be added as it has no emu20kx chip, and is a pure HD-audio
device.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable TWL4030 VTXL/VTXR and VRX digital filters for uplink
and downlink paths, respectively.
This patch also corrects voice 8/16kHz mode selection bit
(SEL_16K) of CODEC_MODE register.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Eliminate direct accesses to the driver_data field.
cf 82ab13b26f15f49be45f15ccc96bfa0b81dfd015
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct device *dev;
expression E;
type T;
@@
- dev->driver_data = (T)E
+ dev_set_drvdata(dev, E)
@@
struct device *dev;
type T;
@@
- (T)dev->driver_data
+ dev_get_drvdata(dev)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Split the name string in hda_codec struct to vendor_name and chip_name
strings to be stored directly from the preset name.
Since mostly only the chip name is referred in many patch_*.c, this
results in the reduction of many codes in the end.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix this warning:
sound/parisc/harmony.c:938: warning: format '%lx' expects type 'long unsigned int',
but argument 2 has type 'resource_size_t'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds a mixer control for the STAC92XX boards to control the
DC bias of mic ports, allowing recording from both powered and
non-powered sources. It replaces the "Mic Output Switch" with "Mic Jack
Mode" to switch between Mic, Line In, and Line Out.
Signed-off-by: Nickolas Lloyd <ultrageek.lloyd@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use default to optimize the switch/case in magicial_playback_hw_params(),
which also fixes the compile warnings below:
sound/soc/pxa/magician.c:89: warning: 'acds' may be used uninitialized in this function
sound/soc/pxa/magician.c:89: warning: 'acps' may be used uninitialized in this function
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a build fix, resyncing the DaVinci EVM ASoC board code
with the version in the DaVinci tree. That resync includes
support for the DM355 EVM, although that board isn't yet in
mainline.
(NOTE: also includes a bugfix to the platform_add_resources
call, recently sent by Chaithrika U S <chaithrika@ti.com> but
not yet merged into the DaVinci tree.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This resyncs the DaVinci I2S code with the version in the DaVinci
tree. The behavioral change uses updated clock interfaces which
recently merged to mainline. Two other changes include adding a
comment on the ASP/McBSP/McASP confusion, and dropping pdev->id in
order to support more boards than just the DM644x EVM.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a buildfix for the DaVinci PCM code, resyncing it with
the version in the DaVinci tree. The notable change is using
current EDMA interfaces, which recently merged to mainline.
(The older interfaces never made it into mainline.)
NOTE: open issue, the DMA should be to/from SRAM; see chip
errata for more info. The artifacts are extremely easy to
hear on DM355 hardware (not yet supported in mainline), but
don't seem as audible on DM6446 hardwaare (which does have
mainline support).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch modifies sh_dac_audio in the following ways:
- use high resolution timer instead of TMU1
- fix cpu/dac.h include
- add future rewrite comment
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The WM9712 can be configured by resistor strapping GPIO4 to behave like
the WM9713 and default to leaving the AC97 link disabled after cold
reset until a warm reset occurs. In this configuration we need to issue
a warm reset after cold to bring the link up so do so. The warm reset
will be harmless on systems that don't need it.
[Changelog rewritten to document the reasoning. -- broonie]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
pxa2xx_i2s_resume is :
- unconditionnaly setting SACR0_ENB
- unsetting SACR0_ENB in saved SACR0 pxa_i2s.sacr0
fix these.
In pxa2xx_i2s_{resume,suspend}, save/restore registers even
when !dai->active.
Signed-off-by: Karl Beldan <karl.beldan@mobile-devices.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
i2s_clk is 'put' for no reason in pxa2xx_i2s_shutdown.
Now we 'get' i2s_clk at probe and 'put' it at driver removal or when
probe fails.
Signed-off-by: Karl Beldan <karl.beldan@mobile-devices.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
- hw_params enables both RPL and REC functions each time : Enable the
appropriate function in pxa2xx_i2s_trigger.
- pxa2xx_i2s_shutdown disables i2s anytime one of RPL or REC function is
off : Turn it off only when both functions are off.
Signed-off-by: Karl Beldan <karl.beldan@mobile-devices.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make sure we are in a know good state at end of probe :
Reset FIFO logic and registers, and make sure REC and RPL functions
along with FIFO service are disabled (SACR0_RST enables REC and RPL).
Resetting loses current settings so remove reset from stream startup.
Now reset occurs only at probe.
Signed-off-by: Karl Beldan <karl.beldan@mobile-devices.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Added the codec SSID for MacBook Pro 5,1 as compatible as MP51.
However, the headphone auto-muting function doesn't work. So,
this is just a tentative solution.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix printk format warning:
sound/drivers/pcsp/pcsp_mixer.c:54: warning: format '%d' expects type 'int', but argument 3 has type 'long unsigned int'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The i2c_device_name() macro is used only once and doesn't have much
value, it hurts redability more than it helps. Get rid of it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Resending the patch after fixing the minor issues.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With a postfix increment these variables are incremented beyond
CMDIF_TIMEOUT / MAX_WRITE_RETRY.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reset FIFO logic and registers, and make sure REC and RPL functions along
with FIFO service are disabled at probe.
Signed-off-by: Karl Beldan <karl.beldan@mobile-devices.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The model=acer for ALC883/889 doesn't work well for the recent Acer
Aspire laptops. Since model=auto works better nowadays, it's safer
to use the default fallback instead of the Acer specific one.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the hdsp driver is built in kernel, the corresponding firmware
files have to be built into the kernel as well (otherwise the boot
will hang up for fairly long time), but there is no way to control
it in Kconfig yet, unfortunately. Instead, show a comment for user
just to make sure.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The inputs of the twl4030 codec can be mixed, so we will use the mixer
DAPM for the analog microphone registers(0x05, 0x06), but if we enable
more than one input at the same time, the input impedance of the input
amplifier will be reduced.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow the use of the FIRMWARE_IN_KERNEL option with hdsp cards and
in-kernel driver.
Also corrected a typo in the comment.
Signed-off-by: Raphael Doursenaud <rdoursenaud@free.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add specific configuration for Samsung NC10 mini notebook. Internal
mic/speakers will be correctly muted when plugging in external ones.
Mixer controls are added for speakers, headphones and PC beep.
"Boost" is added for the microphones.
Signed-off-by: Chris Pockelé <chris.pockele.f1@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the card was not instantiated in snd_soc_instantiate_card, calling
soc-remove will crash because some of codec, cpu_dai and card .remove
methods are called twice.
Fix this by returning from soc_remove immediately.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Added the missing descriptions and the model names for Realtek codecs
to the documentation and the config table.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASoC uses the standard ALSA data format definitions to specify the wire
format used between the CPU and CODEC. Since the ALSA data formats all
include the endianess of the data but this information is not relevant
by the time the data has been encoded onto the serial link to the CODEC
this means that either all the CODEC drivers need to declare both big and
little endian variants or the core needs to fix up the format constraints
specified by CODEC drivers.
For now take the latter approach - this will need to be revisited if any
CODECs are endianness dependant.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC driver for AT91SAM9260-based AFEB9260 board
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Most of unsol handlers defined in patch_realtek.c can be classified to
two types, mute via amp of pins and mute via ctl bits of pins.
Thus there are a big room to generalize each implementation.
This patch creates two generic functions, alc_automute_amp() and
alc_automute_pin(). The latter is actually changed from the previous
alc_sku_automute(). Each caller needs to initialize hp_pins and
speaker_pins properly at own init_hook.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The speaker auto-muting per HP plugging for ALC262 HIPPO and compatible
devices is slightly buggy as the "Master" or "Front" mixer control can
still toggle the speaker output even if the headphone is plugged.
This patch fixes the issue, and clean up the hippo-related codes
together with fixes of some inconsistent mixer names.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Copy-paste error: TWL4030_PRECKL_GAIN >> TWL4030_PRECKR_GAIN
It has not caused problems, since
TWL4030_PRECKL_GAIN == TWL4030_PRECKR_GAIN == 0x30
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
VIA VT1708S and VT1702 codecs can have two SPDIF outputs. One of them
should have been handled as the extra digital out, but it's not
properly accessed.
This patch fixes the handling of the secondary SPDIF on these codecs
with the slave dig-out as found in patch_sigmatel.c. This makes the
use of such a device easier (for normal users).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BIOS on Mac Mini Core2 Duo sets both INPUT and OUTPUT pinctl bits to
the line-in jack, and it confuses the driver as if it's a valid input.
This patch adds the check of OUTPUT bit so that the driver fixes the
invalid pin setup.
Tested-by: Tino Keitel <tino.keitel@gmx.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Added a new flag, own_routing, to allow spec drivers to create own
routing controls. Also, the basic get/put calls are changed to be
external for later use by maya44 driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The set_rate might return error but the current code doesn't check it.
This patch adds a proper error check.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the magic 0x80 value with a suitable macro definition.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With 5 bits and 1.5 dB per step, the DXS volume range is only 48 dB.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove most of the serial port parameters from the card longname string
because it was way too long and overflowed into the mixername string.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added runtime->delay field to adjust the delayed samples for snd_pcm_delay().
Typically a hardware FIFO length is stored in this field, so that the
extra delay between hwptr and applptr can be computed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for the VIBRA output on TWL4030 codec.
The VIBRA output can be driven with audio data or with
local vibrator driver.
Add the needed DAPM elements and routes for the VIBRA output and
controls for the VIBRA driver configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the ASoC side of the board support for the Crossbow
IMB400 daughter board.
Thanks to Crossbow for considerable assistance.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch add voice digital loopback (sidetone) to the twl4030
driver. It mixes voice uplink attenuated (by sidetone gain) with
voice downlink when the codec is working in option2 (voice/audio
mode).
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds voice downlink analog bypass switch. It follows
the same approach as in other analog bypass switches.
DAC switch is moved from 'DAC Voice' to 'Analog Voice Playback Mixer',
that will also allow voice DAC to be powered in digital voice
loopback (sidetone).
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The mis-typing exist in dapm controller definitions and dapm route definitions,
so happen mis-matched error when snd_soc_dapm_add_routes().
Cc: stable@kernel.org
Signed-off-by: Jinyoung Park <parkjy@mtekvision.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com
Add module parameter to enable or disable
joystick port (gameport) on the SC6600 and
later cards.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The AC97 wire format is completely fixed so CODECs don't have any choice
about the formats they accept but controllers accept a variety of data
formats and render them down onto the bus. Have a shared define so all
the CODEC drivers will interoperate with any of our controller drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
calls
The S3C24XX DMA API channel configuration registers are being passed
values comprised of register values which makes it hard to move the
API to cover both the S3C24XX and S3C64XX.
These values can be calculated from knowing which device the channel
is connected to, so remove them from the two calls s3c2410_dma_config
and s3c2410_dma_devconfig.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
They aren't used by anything external and aren't prototyped; if any
users appear they can be exported again for them.
Also report what modes we have a problem with when we encounter invalid
mode configurations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
On startup we try to make sure that the port is quiesced but if the
port is already stopped then this will generate a warning about the
RX/TX mode configuration. Configure the mode before doing the teardown
to suppress these warnings.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The data format configuration for S3C64xx IISv2 is completely different
to that for S3C24xx. Instead of a single bit configuration in bit 0 of
IISMOD we have format selection in bits 13 and 14 and bit clock rate
selection in bits 1 and 2. While we're here add support for 24 bit
samples in S3C64xx.
At some point it may be desirable to expose the bit clock rate selection
to users but given the limited configuration options that may not be
required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This makes the interface usable with the s3c-iis-v2 rate calculator
and consistent with S3C2412.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The gain control for earpiece amplifier uses 0dB ~ 12dB according to the
TRM, but the present code is implemented to -6dB ~ 6dB.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The hardware devices with SNDRV_PCM_INFO_BATCH flag can't give the
precise current position. And such hardwares have often big FIFO
in addition to the ring buffer, and it screws up the jiffies check
in pcm_lib.c.
This patch adds a simple check of info flag so that the driver skips
the jiffies check in snd_pcm_period_elapsed() when BATCH flag is set.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added SNDRV_PCM_INFO_BATCH flag to PCM info field of some drivers that
really don't give the precise pointer value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commmit dfed0ef9b3 was reverted
accidentally by the merge of auto-detection fix patch.
Fixed again now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable auto-muting in model=auto only for devices with HP and speakers.
For devices with HP and line-outs, don't enable the auto-muting.
Also, add a debug print to show the auto-mute feature.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We need to check only if the WM8350 is master and only when starting
the stream so if either is not true then we can skip the check.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This adds a new control named 'Master Playback Switch' for cs4270
codecs. It is implemented using the new SOC_DOUBLE_EXT macro to catch
the put function and store the information about manually set mute
controls from userspace. When a manual mute is set, we don't want the
soc core to un-mute the outputs.
Renamed cs4270_mute() to cs4270_dai_mute() to avoid confusion.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The control modifies the MUTE register, hence the polarity must be
inverted.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-By: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Say what invalid values we're seeing when we see an invalid value and
ensure that errors are displayed by default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's expected behaviour for the CODEC header to provide them but the
WM8350 doesn't due to having all the registers together under drivers/mfd.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In the realtek auto-probing mode, the initialization of amp with
some magic COEF or EAPD verbs is applied only when the codec SSID
has valid values to satisfy the realtek's definition.
However, many devices don't provide in that way, thus the device
doesn't work as is.
This patch allows the same initialization code even if the SSID
doesn't pass the bit test. Also, alc_subsystem_id() is changed
just to check and define the type, so that it's called in the
parser, instead of the initializer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* fix/asoc:
ASoC: s3c-i2s-v2 needs to declare a license for modular builds
ASoC: remove non-existing referece to CONFIG_SND_SOC_CODEC_WM8991
ASoC: Fix WM8580 volume update handling for large register changes
ASoC: Fix offset of freqmode in WM8580 PLL configuration
Fixed the compile warning below by initializatin iomidi variable properly.
sound/pci/cmipci.c: In function ‘snd_cmipci_probe’:
sound/pci/cmipci.c:3017: warning: ‘iomidi’ may be used uninitialized in this function
Signed-off-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Cc: linux-pci <linux-pci@atrey.karlin.mff.cuni.cz>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Sachin P Sant <sachinp@linux.vnet.ibm.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reset the internal period position counter upon stream startup. This
fixes initial aplay underruns and problems related to latency picky
applications such as pulseaudio.
Bumped the version number to 1.3.14.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The S3C64xx IIS code had a number of problems with device registration.
The hardware has two IIS ports of which the driver supported only one
at once via a single exported DAI, attempting to identify the DAI to
use based on the dev->id of the ASoC platform device. As well as
limiting the driver to only supporting one IIS port at once this also
meant that the ID of the soc-audio device (or in future the card device)
had to match the IIS ID.
Fix both problems by converting the driver to register the DAIs based on
probing of platform devices registered by the arch/arm code, using those
platform devices to interact with the clock API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the four channel TDM mode
on Beagle board.
Depending on the channel count, the interface needs to be
configured differently (I2S for stereo DSP_A for four channels)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The last patch to handle newer cards like SC7000
broke initialization of the SC6000. Fix this.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add 4 channel support to omap-mcbsp.
This mode is going to be used by the twl4030 codec, when it
is configured in Option1 mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The original idea came from pHilipp, and this makes the code looks
more consistent.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The SSP DMA parameters can actually be easily generated at run-time since
they are almost similar except for the FIFO width and direction. Another
benefit is the re-use of information from 'struct ssp_device', like SSDR
physical FIFO address and DRCMR register index for both directions.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: pHilipp Zabel <philipp.zabel@gmail.com>
Add DAPMs for VDL(Voice Down Link) path. To support VDL path, we have
to change DAPMs of outputs(Earpiece, PreDrive Left/Right, Headset
Left/Right, Carkit Left/Right) from mux to mixer.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The current ad1884a-mobile model has a problem that the speaker output
doesn't work sometimes after boot or power-saving on some HP laptops.
It seems that the verbs accessing to the non-functional widgets cause
this problem.
This patch simplifies the init verbs for mobile model not to touch
unnecessary setups so that it avoids the speaker-mute problem.
Reference: Novell bnc#495668
https://bugzilla.novell.com/show_bug.cgi?id=495668
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Save a little extra power by enabling the DC servo offset correction
for the output channels only when the relevant channels are enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Modify the default startup sequence in the chip to set the DC servo
dither level for optimal performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CLK_DSP provides a master clock for the DAC and ADC related functionality
on the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many modern CODECs have shared resources on chip which must be enabled
for portions of the chip to work but which can be disabled at other times
in order to achieve power savings. Examples of such resources include
power supplies and some internal clocks.
Since these widgets are dependencies for the audio path but do not carry
audio signals they require slightly different handling to most widgets -
they do not contribute to the audio path and so should not be counted as
either inputs or outputs during path walks.
Cases where one supply provides a supply for another will require
additional work. There is also room for more optimisation of the graph
walking to avoid repeated checks for the same thing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add checking in hw_params and prepare to detect bufferless pcms(i.e. BT
<--> codec).
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Appearently, a big delay ~300ms is required before hw is settled and ready
to transfer samples on some hardware variants. Also, return back
"clocking to 48000Hz" message when something fails.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The current error-recovery scheme for the codec communication errors
doesn't work always well. Especially falling back to the
single-command mode causes the fatal problem on many systems.
In this patch, the problematic verb is re-issued again after the error
(even with polling mode) instead of the single-cmd mode. The
single-cmd mode will be used only when specified via the command
option explicitly, mainly just for testing.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cache quries for PCM and STREAM parameters as well as ampcap and
pincap sharing the hash table. This will reduce the superfluous
access of the same codec verbs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Support ASUS F81Se F5Q P80 U20A U80 U50 UX50 for ALC269
- Support ASUS F70SL UX20 X58LE F50Z N80Vc N81Te N505Tp Vx3V N5051A
for ALC663
- Support DELL ZM1 for ALC272
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Don't unmute unneeded amps for input mixers of ALC662 & co.
It caused possible recording noises.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The legacy i2c binding model is going away soon, so convert the ppc
keywest sound driver to the new model or it will break.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The legacy i2c binding model is going away soon, so convert the AOA
codec drivers to the new model or they'll break.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Andreas Schwab <schwab@linux-m68k.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rather than having switch statements at point of use make the DAPM
power check a member of the widget structure and set it when we
instantiate the widget.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This also switches us to using a switch statement for the widget type
in dapm_power_widget().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This will form a basis for further power check refactoring: the overall
goal of these changes is to allow us to check power separately to
applying it, allowing improvements in the power sequencing algorithms.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add Voice DAI to support the PCM voice interface of the twl4030 codec.
The PCM voice interface can be used with 8-kHz(voice narrowband) or
16-kHz(voice wideband) sampling rates, and 16bits, and mono RX and mono
TX or stereo TX.
The PCM voice interface has two modes
- PCM mode1 : This uses the normal FS polarity and the rising edge of
the clock signal.
- PCM mode2 : This uses the FS polarity inverted and the falling edge
of the clock signal.
If the system master clock is not 26MHz or the twl4030 codec mode is not
option2, the voice PCM interface is not available.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use it to clean up snd_us122l_card_used[].
Without patch unplugging of an US122L soundcard didn't reset the
corresponding element of snd_us122l_card_used[] to 0.
The (SNDRV_CARDS + 1)th plugging in did not result in creating the soundcard
device anymore.
Index values supplied with the modprobe command line were not used correctly
anymore after the first unplugging of an US122L.
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the missing definition of max channels for CA0110, which resulted
in an error at opening PCM devices.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
