This patch adds accounting to each runqueue to keep track of the
highest prio task queued on the run queue. We only care about
RT tasks, so if the run queue does not contain any active RT tasks
its priority will be considered MAX_RT_PRIO.
This information will be used for later patches.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds accounting to keep track of the number of RT tasks running
on a runqueue. This information will be used in later patches.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
this patch extends the soft-lockup detector to automatically
detect hung TASK_UNINTERRUPTIBLE tasks. Such hung tasks are
printed the following way:
------------------>
INFO: task prctl:3042 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message
prctl D fd5e3793 0 3042 2997
f6050f38 00000046 00000001 fd5e3793 00000009 c06d8264 c06dae80 00000286
f6050f40 f6050f00 f7d34d90 f7d34fc8 c1e1be80 00000001 f6050000 00000000
f7e92d00 00000286 f6050f18 c0489d1a f6050f40 00006605 00000000 c0133a5b
Call Trace:
[<c04883a5>] schedule_timeout+0x6d/0x8b
[<c04883d8>] schedule_timeout_uninterruptible+0x15/0x17
[<c0133a76>] msleep+0x10/0x16
[<c0138974>] sys_prctl+0x30/0x1e2
[<c0104c52>] sysenter_past_esp+0x5f/0xa5
=======================
2 locks held by prctl/3042:
#0: (&sb->s_type->i_mutex_key#5){--..}, at: [<c0197d11>] do_fsync+0x38/0x7a
#1: (jbd_handle){--..}, at: [<c01ca3d2>] journal_start+0xc7/0xe9
<------------------
the current default timeout is 120 seconds. Such messages are printed
up to 10 times per bootup. If the system has crashed already then the
messages are not printed.
if lockdep is enabled then all held locks are printed as well.
this feature is a natural extension to the softlockup-detector (kernel
locked up without scheduling) and to the NMI watchdog (kernel locked up
with IRQs disabled).
[ Gautham R Shenoy <ego@in.ibm.com>: CPU hotplug fixes. ]
[ Andrew Morton <akpm@linux-foundation.org>: build warning fix. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
This patch converts the known per-subsystem mutexes to get_online_cpus
put_online_cpus. It also eliminates the CPU_LOCK_ACQUIRE and
CPU_LOCK_RELEASE hotplug notification events.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Replace all lock_cpu_hotplug/unlock_cpu_hotplug from the kernel and use
get_online_cpus and put_online_cpus instead as it highlights the
refcount semantics in these operations.
The new API guarantees protection against the cpu-hotplug operation, but
it doesn't guarantee serialized access to any of the local data
structures. Hence the changes needs to be reviewed.
In case of pseries_add_processor/pseries_remove_processor, use
cpu_maps_update_begin()/cpu_maps_update_done() as we're modifying the
cpu_present_map there.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The current load balancing scheme isn't good enough for precise
group fairness.
For example: on a 8-cpu system, I created 3 groups as under:
a = 8 tasks (cpu.shares = 1024)
b = 4 tasks (cpu.shares = 1024)
c = 3 tasks (cpu.shares = 1024)
a, b and c are task groups that have equal weight. We would expect each
of the groups to receive 33.33% of cpu bandwidth under a fair scheduler.
This is what I get with the latest scheduler git tree:
Signed-off-by: Ingo Molnar <mingo@elte.hu>
--------------------------------------------------------------------------------
Col1 | Col2 | Col3 | Col4
------|---------|-------|-------------------------------------------------------
a | 277.676 | 57.8% | 54.1% 54.1% 54.1% 54.2% 56.7% 62.2% 62.8% 64.5%
b | 116.108 | 24.2% | 47.4% 48.1% 48.7% 49.3%
c | 86.326 | 18.0% | 47.5% 47.9% 48.5%
--------------------------------------------------------------------------------
Explanation of o/p:
Col1 -> Group name
Col2 -> Cumulative execution time (in seconds) received by all tasks of that
group in a 60sec window across 8 cpus
Col3 -> CPU bandwidth received by the group in the 60sec window, expressed in
percentage. Col3 data is derived as:
Col3 = 100 * Col2 / (NR_CPUS * 60)
Col4 -> CPU bandwidth received by each individual task of the group.
Col4 = 100 * cpu_time_recd_by_task / 60
[I can share the test case that produces a similar o/p if reqd]
The deviation from desired group fairness is as below:
a = +24.47%
b = -9.13%
c = -15.33%
which is quite high.
After the patch below is applied, here are the results:
--------------------------------------------------------------------------------
Col1 | Col2 | Col3 | Col4
------|---------|-------|-------------------------------------------------------
a | 163.112 | 34.0% | 33.2% 33.4% 33.5% 33.5% 33.7% 34.4% 34.8% 35.3%
b | 156.220 | 32.5% | 63.3% 64.5% 66.1% 66.5%
c | 160.653 | 33.5% | 85.8% 90.6% 91.4%
--------------------------------------------------------------------------------
Deviation from desired group fairness is as below:
a = +0.67%
b = -0.83%
c = +0.17%
which is far better IMO. Most of other runs have yielded a deviation within
+-2% at the most, which is good.
Why do we see bad (group) fairness with current scheuler?
=========================================================
Currently cpu's weight is just the summation of individual task weights.
This can yield incorrect results. For ex: consider three groups as below
on a 2-cpu system:
CPU0 CPU1
---------------------------
A (10) B(5)
C(5)
---------------------------
Group A has 10 tasks, all on CPU0, Group B and C have 5 tasks each all
of which are on CPU1. Each task has the same weight (NICE_0_LOAD =
1024).
The current scheme would yield a cpu weight of 10240 (10*1024) for each cpu and
the load balancer will think both CPUs are perfectly balanced and won't
move around any tasks. This, however, would yield this bandwidth:
A = 50%
B = 25%
C = 25%
which is not the desired result.
What's changing in the patch?
=============================
- How cpu weights are calculated when CONFIF_FAIR_GROUP_SCHED is
defined (see below)
- API Change
- Two tunables introduced in sysfs (under SCHED_DEBUG) to
control the frequency at which the load balance monitor
thread runs.
The basic change made in this patch is how cpu weight (rq->load.weight) is
calculated. Its now calculated as the summation of group weights on a cpu,
rather than summation of task weights. Weight exerted by a group on a
cpu is dependent on the shares allocated to it and also the number of
tasks the group has on that cpu compared to the total number of
(runnable) tasks the group has in the system.
Let,
W(K,i) = Weight of group K on cpu i
T(K,i) = Task load present in group K's cfs_rq on cpu i
T(K) = Total task load of group K across various cpus
S(K) = Shares allocated to group K
NRCPUS = Number of online cpus in the scheduler domain to
which group K is assigned.
Then,
W(K,i) = S(K) * NRCPUS * T(K,i) / T(K)
A load balance monitor thread is created at bootup, which periodically
runs and adjusts group's weight on each cpu. To avoid its overhead, two
min/max tunables are introduced (under SCHED_DEBUG) to control the rate
at which it runs.
Fixes from: Peter Zijlstra <a.p.zijlstra@chello.nl>
- don't start the load_balance_monitor when there is only a single cpu.
- rename the kthread because its currently longer than TASK_COMM_LEN
Signed-off-by: Srivatsa Vaddagiri <vatsa@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
doms_cur[] array represents various scheduling domains which are
mutually exclusive. Currently cpusets code can modify this array (by
calling partition_sched_domains()) as a result of user modifying
sched_load_balance flag for various cpusets.
This patch introduces a mutex and corresponding API (only when
CONFIG_FAIR_GROUP_SCHED is defined) which allows a reader to safely read
the doms_cur[] array w/o worrying abt concurrent modifications to the
array.
The fair group scheduler code (introduced in next patch of this series)
makes use of this mutex to walk thr' doms_cur[] array while rebalancing
shares of task groups across cpus.
Signed-off-by: Srivatsa Vaddagiri <vatsa@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch changes how the cpu load exerted by fair_sched_class tasks
is calculated. Load exerted by fair_sched_class tasks on a cpu is now
a summation of the group weights, rather than summation of task weights.
Weight exerted by a group on a cpu is dependent on the shares allocated
to it.
This version of patch has a minor impact on code size, but should have
no runtime/functional impact for !CONFIG_FAIR_GROUP_SCHED.
Signed-off-by: Srivatsa Vaddagiri <vatsa@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Minor bug fixes for the group scheduler:
- Use a mutex to serialize add/remove of task groups and also when
changing shares of a task group. Use the same mutex when printing
cfs_rq debugging stats for various task groups.
- Use list_for_each_entry_rcu in for_each_leaf_cfs_rq macro (when
walking task group list)
Signed-off-by: Srivatsa Vaddagiri <vatsa@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
setting cpu share to 1 causes hangs, as reported in:
http://bugzilla.kernel.org/show_bug.cgi?id=9779
as the default share is 1024, the values of 0 and 1 can indeed
cause problems. Limit it to 2 or higher values.
These values can only be set by the root user - but still it
makes sense to protect against nonsensical values.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The show_task function invoked by sysrq-t et al displays the
pid and parent's pid of each task. It seems more useful to
show the actual process hierarchy here than who is using
ptrace on each process.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some services (e.g. sched_setscheduler(), rt_mutex_setprio() and
sched_move_task()) must handle a given task differently in case it's the
'rq->curr' task on its run-queue. The task_running() interface is not
suitable for determining such tasks for platforms with one of the
following options:
#define __ARCH_WANT_UNLOCKED_CTXSW
#define __ARCH_WANT_INTERRUPTS_ON_CTXSW
Due to the fact that it makes use of 'p->oncpu == 1' as a criterion but
such a task is not necessarily 'rq->curr'.
The detailed explanation is available here:
https://lists.linux-foundation.org/pipermail/containers/2007-December/009262.html
Signed-off-by: Dmitry Adamushko <dmitry.adamushko@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Dhaval Giani <dhaval@linux.vnet.ibm.com>
Tested-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
some platforms have sched_clock() implementations that cannot be called
very early during wakeup. If it's called it might hang or crash in hard
to debug ways. So only call update_rq_clock() [which calls sched_clock()]
if sched_init() has already been called. (rq->idle is NULL before the
scheduler is initialized.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
style cleanup of various changes that were done recently.
no code changed:
text data bss dec hex filename
23680 2542 28 26250 668a sched.o.before
23680 2542 28 26250 668a sched.o.after
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Luiz Fernando N. Capitulino reported that sched_rr_get_interval()
crashes for SCHED_OTHER tasks that are on an idle runqueue.
The fix is to return a 0 timeslice for tasks that are on an idle
runqueue. (and which are not running, obviously)
this also shrinks the code a bit:
text data bss dec hex filename
47903 3934 336 52173 cbcd sched.o.before
47885 3934 336 52155 cbbb sched.o.after
Reported-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit cfb5285660 removed a useful feature for
us, which provided a cpu accounting resource controller. This feature would be
useful if someone wants to group tasks only for accounting purpose and doesnt
really want to exercise any control over their cpu consumption.
The patch below reintroduces the feature. It is based on Paul Menage's
original patch (Commit 62d0df6406), with
these differences:
- Removed load average information. I felt it needs more thought (esp
to deal with SMP and virtualized platforms) and can be added for
2.6.25 after more discussions.
- Convert group cpu usage to be nanosecond accurate (as rest of the cfs
stats are) and invoke cpuacct_charge() from the respective scheduler
classes
- Make accounting scalable on SMP systems by splitting the usage
counter to be per-cpu
- Move the code from kernel/cpu_acct.c to kernel/sched.c (since the
code is not big enough to warrant a new file and also this rightly
needs to live inside the scheduler. Also things like accessing
rq->lock while reading cpu usage becomes easier if the code lived in
kernel/sched.c)
The patch also modifies the cpu controller not to provide the same accounting
information.
Tested-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Tested the patches on top of 2.6.24-rc3. The patches work fine. Ran
some simple tests like cpuspin (spin on the cpu), ran several tasks in
the same group and timed them. Compared their time stamps with
cpuacct.usage.
Signed-off-by: Srivatsa Vaddagiri <vatsa@linux.vnet.ibm.com>
Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
cpu_down() code is ok wrt sched_idle_next() placing the 'idle' task not
at the beginning of the queue.
So get rid of activate_idle_task() and make use of activate_task() instead.
It is the same as activate_task(), except for the update_rq_clock(rq) call
that is redundant.
Code size goes down:
text data bss dec hex filename
47853 3934 336 52123 cb9b sched.o.before
47828 3934 336 52098 cb82 sched.o.after
Signed-off-by: Dmitry Adamushko <dmitry.adamushko@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Grant Wilson has reported rare SCHED_FAIR_USER crashes on his quad-core
system, which crashes can only be explained via runqueue corruption.
there is a narrow SMP race in __set_task_cpu(): after ->cpu is set up to
a new value, task_rq_lock(p, ...) can be successfuly executed on another
CPU. We must ensure that updates of per-task data have been completed by
this moment.
this bug has been hiding in the Linux scheduler for an eternity (we never
had any explicit barrier for task->cpu in set_task_cpu() - so the bug was
introduced in 2.5.1), but only became visible via set_task_cfs_rq() being
accidentally put after the task->cpu update. It also probably needs a
sufficiently out-of-order CPU to trigger.
Reported-by: Grant Wilson <grant.wilson@zen.co.uk>
Signed-off-by: Dmitry Adamushko <dmitry.adamushko@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Suppose that the SCHED_FIFO task does
switch_uid(new_user);
Now, p->se.cfs_rq and p->se.parent both point into the old
user_struct->tg because sched_move_task() doesn't call set_task_cfs_rq()
for !fair_sched_class case.
Suppose that old user_struct/task_group is freed/reused, and the task
does
sched_setscheduler(SCHED_NORMAL);
__setscheduler() sets fair_sched_class, but doesn't update
->se.cfs_rq/parent which point to the freed memory.
This means that check_preempt_wakeup() doing
while (!is_same_group(se, pse)) {
se = parent_entity(se);
pse = parent_entity(pse);
}
may OOPS in a similar way if rq->curr or p did something like above.
Perhaps we need something like the patch below, note that
__setscheduler() can't do set_task_cfs_rq().
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently the scheduler checks for PF_VCPU to decide if this timeslice
has to be accounted as guest time. On s390 host interrupts are not
disabled during guest execution. This causes theses interrupts to be
accounted as guest time if CONFIG_VIRT_CPU_ACCOUNTING is set. Solution
is to check if an interrupt triggered account_system_time. As the tick
is timer interrupt based, we have to subtract hardirq_offset.
I tested the patch on s390 with CONFIG_VIRT_CPU_ACCOUNTING and on
x86_64. Seems to work.
CC: Avi Kivity <avi@qumranet.com>
CC: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Revert 62d0df6406.
This was originally intended as a simple initial example of how to create a
control groups subsystem; it wasn't intended for mainline, but I didn't make
this clear enough to Andrew.
The CFS cgroup subsystem now has better functionality for the per-cgroup usage
accounting (based directly on CFS stats) than the "usage" status file in this
patch, and the "load" status file is rather simplistic - although having a
per-cgroup load average report would be a useful feature, I don't believe this
patch actually provides it. If it gets into the final 2.6.24 we'd probably
have to support this interface for ever.
Cc: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds a proper prototype for migration_init() in
include/linux/sched.h
Since there's no point in always returning 0 to a caller that doesn't check
the return value it also changes the function to return void.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
SMP balancing is done with IRQs disabled and can iterate the full rq.
When rqs are large this can cause large irq-latencies. Limit the nr of
iterations on each run.
This fixes a scheduling latency regression reported by the -rt folks.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Tested-by: Gregory Haskins <ghaskins@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
remove PREEMPT_RESTRICT. (this is a separate commit so that any
regression related to the removal itself is bisectable)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
PREEMPT_RESTRICT was a method aimed at reducing the amount of wakeup
related preemption. It has a disadvantage though, it can prevent
legitimate wakeups if a task is 'unlucky' to be hit too early by a tick
that clears peer_preempt.
Now that the wakeup preemption has been cleaned up we dont seem to have
excessive preemptions anymore, so this feature can be turned off. (and
removed in the next patch)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
1) hardcoded 1000000000 value is used five times in places where
NSEC_PER_SEC might be more readable.
2) A conversion from nsec to msec uses the hardcoded 1000000 value,
which is a candidate for NSEC_PER_MSEC.
no code changed:
text data bss dec hex filename
44359 3326 36 47721 ba69 sched.o.before
44359 3326 36 47721 ba69 sched.o.after
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Yanmin Zhang reported an aim7 regression and bisected it down to:
| commit 38ad464d41
| Author: Ingo Molnar <mingo@elte.hu>
| Date: Mon Oct 15 17:00:02 2007 +0200
|
| sched: uniform tunings
|
| use the same defaults on both UP and SMP.
fix this by reintroducing similar SMP tunings again. This resolves
the regression.
(also update the comments to match the ilog2(nr_cpus) tuning effect)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Adds a cpu.usage file to the CFS cgroup that reports CPU usage in
milliseconds for that cgroup's tasks
[ mingo@elte.hu: style cleanups. ]
Signed-off-by: Paul Menage <menage@google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Peter Zijlstra noticed that the rcu_head object need not be present
in every cfs_rq of a group. Move it to the task_group structure
instead.
Signed-off-by: Srivatsa Vaddagiri <vatsa@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch:
commit 9b5b77512d
Author: Srivatsa Vaddagiri <vatsa@linux.vnet.ibm.com>
Date: Mon Oct 15 17:00:09 2007 +0200
sched: clean up code under CONFIG_FAIR_GROUP_SCHED
Introduced an assumption of the existence of CPU0 via this line
cfs_rq = tg->cfs_rq[0];
If you have no CPU0, that will be NULL. The fix seems to be just to
take whatever cfs_rq queue comes out of the for_each_possible_cpu()
loop, since they're all equally good for the destruction operation.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
At the moment, a lot of load balancing code that is irrelevant to non
SMP systems gets included during non SMP builds.
This patch addresses this issue and reduces the binary size on non
SMP systems:
text data bss dec hex filename
10983 28 1192 12203 2fab sched.o.before
10739 28 1192 11959 2eb7 sched.o.after
Signed-off-by: Peter Williams <pwil3058@bigpond.net.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
At the moment, balance_tasks() provides low level functionality for both
move_tasks() and move_one_task() (indirectly) via the load_balance()
function (in the sched_class interface) which also provides dual
functionality. This dual functionality complicates the interfaces and
internal mechanisms and makes the run time overhead of operations that
are called with two run queue locks held.
This patch addresses this issue and reduces the overhead of these
operations.
Signed-off-by: Peter Williams <pwil3058@bigpond.net.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
- replace "cont" with "cgrp" in a few places in the CFS cgroup code,
- use write_uint rather than write for cpu.shares write function
Signed-off-by: Paul Menage <menage@google.com>
Acked-by : Srivatsa Vaddagiri <vatsa@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
A full register dump along with stack backtrace would make the
"scheduling while atomic" message more helpful. Use show_regs() instead
of dump_stack() for this. We already know we're atomic in here (that is
why this function was called) so show_regs()'s atomicity expectations
are guaranteed.
Also, modify the output of the "BUG: scheduling while atomic:" header a
bit to keep task->comm and task->pid together and preempt_count() after
them.
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
clean up sched_domain_debug().
this also shrinks the code a bit:
text data bss dec hex filename
50474 4306 480 55260 d7dc sched.o.before
50404 4306 480 55190 d796 sched.o.after
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Jeff Dike noticed that wait_for_completion_interruptible()'s prototype
had a mismatched fastcall.
Fix this by removing the fastcall attributes from all the completion APIs.
Found-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
commit 029190c515 (cpuset
sched_load_balance flag) was not tested SCHED_DEBUG enabled as
committed as it dereferences NULL when used and it reordered
the sysctl registration to cause it to never show any domains
or their tunables.
Fixes:
1) restore arch_init_sched_domains ordering
we can't walk the domains before we build them
presently we register cpus with empty directories (no domain
directories or files).
2) make unregister_sched_domain_sysctl do nothing when already unregistered
detach_destroy_domains is now called one set of cpus at a time
unregister_syctl dereferences NULL if called with a null.
While the the function would always dereference null if called
twice, in the previous code it was always called once and then
was followed a register. So only the hidden bug of the
sysctl_root_table not being allocated followed by an attempt to
free it would have shown the error.
3) always call unregister and register in partition_sched_domains
The code is "smart" about unregistering only needed domains.
Since we aren't guaranteed any calls to unregister, always
unregister. Without calling register on the way out we
will not have a table or any sysctl tree.
4) warn if register is called without unregistering
The previous table memory is lost, leaving pointers to the
later freed memory in sysctl and leaking the memory of the
tables.
Before this patch on a 2-core 4-thread box compiled for SMT and NUMA,
the domains appear empty (there are actually 3 levels per cpu). And as
soon as two domains a null pointer is dereferenced (unreliable in this
case is stack garbage):
bu19a:~# ls -R /proc/sys/kernel/sched_domain/
/proc/sys/kernel/sched_domain/:
cpu0 cpu1 cpu2 cpu3
/proc/sys/kernel/sched_domain/cpu0:
/proc/sys/kernel/sched_domain/cpu1:
/proc/sys/kernel/sched_domain/cpu2:
/proc/sys/kernel/sched_domain/cpu3:
bu19a:~# mkdir /dev/cpuset
bu19a:~# mount -tcpuset cpuset /dev/cpuset/
bu19a:~# cd /dev/cpuset/
bu19a:/dev/cpuset# echo 0 > sched_load_balance
bu19a:/dev/cpuset# mkdir one
bu19a:/dev/cpuset# echo 1 > one/cpus
bu19a:/dev/cpuset# echo 0 > one/sched_load_balance
Unable to handle kernel paging request for data at address 0x00000018
Faulting instruction address: 0xc00000000006b608
NIP: c00000000006b608 LR: c00000000006b604 CTR: 0000000000000000
REGS: c000000018d973f0 TRAP: 0300 Not tainted (2.6.23-bml)
MSR: 9000000000009032 <EE,ME,IR,DR> CR: 28242442 XER: 00000000
DAR: 0000000000000018, DSISR: 0000000040000000
TASK = c00000001912e340[1987] 'bash' THREAD: c000000018d94000 CPU: 2
..
NIP [c00000000006b608] .unregister_sysctl_table+0x38/0x110
LR [c00000000006b604] .unregister_sysctl_table+0x34/0x110
Call Trace:
[c000000018d97670] [c000000007017270] 0xc000000007017270 (unreliable)
[c000000018d97720] [c000000000058710] .detach_destroy_domains+0x30/0xb0
[c000000018d977b0] [c00000000005cf1c] .partition_sched_domains+0x1bc/0x230
[c000000018d97870] [c00000000009fdc4] .rebuild_sched_domains+0xb4/0x4c0
[c000000018d97970] [c0000000000a02e8] .update_flag+0x118/0x170
[c000000018d97a80] [c0000000000a1768] .cpuset_common_file_write+0x568/0x820
[c000000018d97c00] [c00000000009d95c] .cgroup_file_write+0x7c/0x180
[c000000018d97cf0] [c0000000000e76b8] .vfs_write+0xe8/0x1b0
[c000000018d97d90] [c0000000000e810c] .sys_write+0x4c/0x90
[c000000018d97e30] [c00000000000852c] syscall_exit+0x0/0x40
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
KVM clears it by itself now, and for s390 this is plain wrong.
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Enable "cgroup" (formerly containers) based fair group scheduling. This
will let administrator create arbitrary groups of tasks (using "cgroup"
pseudo filesystem) and control their cpu bandwidth usage.
[akpm@linux-foundation.org: fix cpp condition]
Signed-off-by: Srivatsa Vaddagiri <vatsa@linux.vnet.ibm.com>
Signed-off-by: Dhaval Giani <dhaval@linux.vnet.ibm.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Paul Menage <menage@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a cpu is disabled, move_task_off_dead_cpu() is called for tasks that have
been running on that cpu.
Currently, such a task is migrated:
1) to any cpu on the same node as the disabled cpu, which is both online
and among that task's cpus_allowed
2) to any cpu which is both online and among that task's cpus_allowed
It is typical of a multithreaded application running on a large NUMA system to
have its tasks confined to a cpuset so as to cluster them near the memory that
they share. Furthermore, it is typical to explicitly place such a task on a
specific cpu in that cpuset. And in that case the task's cpus_allowed
includes only a single cpu.
This patch would insert a preference to migrate such a task to some cpu within
its cpuset (and set its cpus_allowed to its entire cpuset).
With this patch, migrate the task to:
1) to any cpu on the same node as the disabled cpu, which is both online
and among that task's cpus_allowed
2) to any online cpu within the task's cpuset
3) to any cpu which is both online and among that task's cpus_allowed
In order to do this, move_task_off_dead_cpu() must make a call to
cpuset_cpus_allowed_locked(), a new subset of cpuset_cpus_allowed(), that will
not block. (name change - per Oleg's suggestion)
Calls are made to cpuset_lock() and cpuset_unlock() in migration_call() to set
the cpuset mutex during the whole migrate_live_tasks() and
migrate_dead_tasks() procedure.
[akpm@linux-foundation.org: build fix]
[pj@sgi.com: Fix indentation and spacing]
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Paul Jackson <pj@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The task_struct->pid member is going to be deprecated, so start
using the helpers (task_pid_nr/task_pid_vnr/task_pid_nr_ns) in
the kernel.
The first thing to start with is the pid, printed to dmesg - in
this case we may safely use task_pid_nr(). Besides, printks produce
more (much more) than a half of all the explicit pid usage.
[akpm@linux-foundation.org: git-drm went and changed lots of stuff]
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
