state is unsigned long so the test did not work.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Otherwise polling will continue for the thermal zone even when
it is no longer needed, for example because forced passive cooling
was disabled.
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Setting polling_delay is useless as passive_delay has priority,
so the value shown in proc isn't the actual polling delay. It
also gives the impression to the user that he can change the
polling interval through proc, while in fact he can't.
Also, unset passive_delay when the forced passive trip point is
unbound to allow polling to be disabled.
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Values below 1000 milli-celsius don't make sense and can cause the
system to go into a thermal heart attack: the actual temperature
will always be lower and thus the system will be throttled down to
its lowest setting.
An additional problem is that values below 1000 will show as 0 in
/proc/acpi/thermal/TZx/trip_points:passive.
cat passive
0
echo -n 90 >passive
bash: echo: write error: Invalid argument
echo -n 90000 >passive
cat passive
90000
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Make the trip_point_N_type sysfs files return a string ending in EOL for
consistency with other sysfs files.
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The return value of the get_temp function is not checked when doing a
thermal zone update. This may lead to a critical shutdown if get_temp
fails and the content of the temp variable is incorrectly set higher than
the critical trip point.
This has been observed on a system with incorrect ACPI implementation
where the corresponding methods were not serialized and therefore
sometimes triggered ACPI errors (AE_ALREADY_EXISTS). The following
critical shutdowns indicated a temperature of 2097 C, which was obviously
wrong.
The patch adds a return value check that jumps over all trip point
evaluations printing a warning if get_temp fails. The trip points are
evaluated again on the next polling interval with successful get_temp
execution.
Signed-off-by: Michael Brunner <mibru@gmx.de>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a regression caused by commit
b1569e99c7
"ACPI: move thermal trip handling to generic thermal layer"
which accidentally changed trip point trigger condition to
temp > trip_temp
This patch changes the trigger condition back to
temp >= trip_temp
Signed-off-by: Vladimir Zajac <eightgraph@gmail.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Due to poor thermal design or Linux driving hardware outside its thermal
envelope, some systems will reach critical temperature and shut down
under high load. This patch adds support for forcing a polling-based
passive trip point if the firmware doesn't provide one. The assumption
is made that the processor is the most practical means to reduce the
dynamic heat generation, so hitting the passive thermal limit will cause
the CPU to be throttled until the temperature stabalises around the
defined value.
UI is provided via a "passive" sysfs entry in the thermal zone
directory. It accepts a decimal value in millidegrees celsius, or "0" to
disable the functionality. Default behaviour is for this functionality
to be disabled.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The ACPI code currently carries its own thermal trip handling, meaning that
any other thermal implementation will need to reimplement it. Move the code
to the generic thermal layer.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The thermal API currently uses strings to pass values to userspace. This
makes it difficult to use from within the kernel. Change the interface
to use integers and fix up the consumers.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
A bug in libsensors <= 2.10.6 is exposed
when this new hwmon I/F is enabled.
Create CONFIG_THERMAL_HWMON=n
until some time after libsensors 2.10.7 ships
so those users can run the latest kernel.
libsensors 3.x is already fixed -- those users
can use CONFIG_THERMAL_HWMON=y now.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Acked-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Len Brown <len.brown@intel.com>
