Kill snd_assert() in sound/pci/*, either removed or replaced with
if () with snd_BUG_ON().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The VT1724 MIDI port is not MPU-401 compatible; remove the hacks that
try to make the MPU-401 library work with it, and just use some simple
device-specific code.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Pavel Hofman <pavel.hofman@insite.cz>
The sound boards with VT1724 and compatible chips may lock up when
MPU401 is accessed together with the PCM streaming.
This patch fixes the problem.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
free_irq() calls synchronize_irq() for you, so there is no need for
drivers to manually do the same thing (again). Thus, calls where
sync-irq immediately precedes free-irq can be simplified.
However, during this audit several bugs were noticed, where free-irq is
preceded by a "irq >= 0" check... but the sync-irq call is not covered
by the same check.
So, where sync-irq could not be eliminated completely, the missing check
was added.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Correct some arguments in calls to snd_ice1712_gpio_write_bits() from
ap192_set_rate_val().
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some calls to snd_ice1712_gpio_write() go wrong, if
snd_ice1712_gpio_write_bits() ran before and changed the gpio mask register.
Read the actual gpio value and combine it with the to be set bits in the cpu
instead.
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Let "chip reset" become first. Increasement of the "chip reset" related timeout
leads to correctly read eeprom's contents here.
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* moving most of clock-specific code to card-specific routines
* support for ESI Juli
* to-be-researched - monitoring of analog/digital inputs
Signed-off-by: Pavel Hofman <dustin@seznam.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* removing the hack with NON_AKM ak4xxx type
* support for card-specific flags in ak4114_stats
* definition of the flags for corresponding cards
Signed-off-by: Pavel Hofman <dustin@seznam.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AK4114 on Juli@ has the SPDIF input sample rate detection and
causes errors when an incompatible sample rate is chosen.
The patch adds the open hook to check the current rate and limit
the hw constraints.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In all four case, adding a private value to the iooff index,
call it priv_idx.
sound/pci/ice1712/ice1712.c:1300:6: warning: symbol 'index' shadows an earlier one
sound/pci/ice1712/ice1712.c:85:12: originally declared here
sound/pci/ice1712/ice1712.c:1312:6: warning: symbol 'index' shadows an earlier one
sound/pci/ice1712/ice1712.c:85:12: originally declared here
sound/pci/ice1712/ice1712.c:1338:6: warning: symbol 'index' shadows an earlier one
sound/pci/ice1712/ice1712.c:85:12: originally declared here
sound/pci/ice1712/ice1712.c:1350:6: warning: symbol 'index' shadows an earlier one
sound/pci/ice1712/ice1712.c:85:12: originally declared here
[tiwai - fixed coding issues as well]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
See ALSA bug#3327 for more details. Experimental.
Also fix support for M-Audio Delta 1010E - subdevice check.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fixes the problems with Midi In on Hoontech/STA dsp24 cards, for example with
DSP2000 box, without restricting the box configurations available. Also adds
mpu_401 name strings.
Signed-off-by: Alan Horstmann <gineera@aspect135.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Don't need to declare a struct when defining a structure layout. Both
of these structs are unused.
sound/pci/ice1712/revo.c:39:3: warning: symbol 'revo51' was not declared. Should it be static?
sound/pci/ice1712/phase.c:54:3: warning: symbol 'phase28' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clean up ice1712/ice1724 codes. The board-specific data is allocated
locally in each code instead of having an ungly union in struct ice1712.
Also, fix coding issues in prodigy_hifi.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
See ALSA bug#2384 for more details.
Signed-off-by: Julian Scheel <julian@jusst.de>
Signed-off-by: Konstantin Kletschke <konsti@ku-gbr.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This header file exists only for some hacks to adapt alsa-driver
tree. It's useless for building in the kernel. Let's move a few
lines in it to sound/core.h and remove it.
With this patch, sound/driver.h isn't removed but has just a single
compile warning to include it. This should be really killed in
future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
* support for switching rate in STAC9460 - using set_rate_val of the akm
infrastructure
* listing all STAC9460 registers in proc
* disabling mpu401 device for Prodigy192 - otherwise the currently
flawed mpu401 code hangs kernel when opening the midi device
* removing old unused commented-out code
Signed-off-by: Pavel Hofman <dustin@seznam.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The 'Word Clock Status' control on Delta 1010LT checks the CS8427
error register too strictly and almost always returns 1 (unlocked).
It should check only the lock status bit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Clean up ctl callbacks of SE-200PCI driver. Also make sure to check
the value ranges.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Check the value ranges in ctl put callbacks properly.
Also fixed the wrong access type to enum elements in aureon.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the support for Onkyo SE-90PCI and SE-200PCI boards.
Signed-off-by: Shin-ya Okada <sh_okada at d4.dion.ne.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
It is possible to have linked substreams that belong to different cards
and/or different drivers. This patch changes some drivers to make sure
that they do not incorrectly try to handle substreams of a different
card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
There were some places I forgot to replace with snd_ctl_boolean_mono_info.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Clean up codes using the new common snd_ctl_boolean_*_info() callbacks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds the support of mute for front channels of M-Audio
Revolution 7.1 (the DAC AK4381 features a mute bit).
Signed-off-by: Pavel Hofman <dustin@seznam.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
- always set 256fs in SPDIF master clock mode
- disable deemphasis filter in AK4114 for Prodigy192
Signed-off-by: Pavel Hofman <dustin@seznam.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fixes:
--------
* correct card specific ice1724 initialization
* working IEC958 output of the card
* renamed capture controls
New features:
------------------
* analog input switch (line-in/mic)
* optional ak4114 based MI/ODI/O card detection & support: IEC958 input,
digital input switch (toslink/coax)
Unresolved issues
-----------------------
* Analog and digital input enums are listed on playback panel of alsamixer,
I do not know how to push them onto the capture one.
Signed-off-by: Pavel Hofman <dustin@seznam.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added some comments regarding naming of PCM streams on vt172x chip.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Call snd_ak4114_build() in juli support code to build proper mixer
elements for SPDIF inputs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
ak4114 code may trigger Oops when the parameters are changed without
call of snd_ak4114_build(). Now it checks the existence of kctl
element, and the workq is triggered after building the necessary
kcontrols.
Also, did some code clean up.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
ap192_4wire_start() in ice1712/revo.c returns unsigned char
whereas it should return unsigned int.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Marvin told with a depressed face,
gcc doesn't like both __devinitdata and const in the same line.
So, remove const from all over places now...
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
CC [M] sound/pci/ice1712/ice1712.o
sound/pci/ice1712/ice1712.c:290: error: snd_ice1712_mixer_digmix_route_ac97 causes a section type conflict
sound/pci/ice1712/ice1712.c:1630: error: snd_ice1712_eeprom causes a section type conflict
...
Gcc like its __devinitdata readable not const, it seems. An alternative
fix would be to remove the __devinitdata attribute but that would result
in slight runtime bloat.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added a new macro snd_pcm_group_for_each_entry() just for code cleanup.
Old macros, snd_pcm_group_for_each() and snd_pcm_group_substream_entry(),
are removed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fix the misspellings of "propogate", "writting" and (oh, the shame
:-) "kenrel" in the source tree.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Mark TLV data as 'const'
Signed-of-by: Philipp Matthias Hahn <pmhahn@pmhahn.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Make data passed to ak4xxx_create 'const'.
Signed-of-by: Philipp Matthias Hahn <pmhahn@pmhahn.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Mark a lot of data as 'const'
Signed-of-by: Philipp Matthias Hahn <pmhahn@pmhahn.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Reorganize EEPROM data (in C99 style).
Signed-of-by: Philipp Matthias Hahn <pmhahn@pmhahn.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds the support of the ESI Waveterminal 192M soundcard
to the ice1724 familly ALSA driver.
It's a semi-professionnal soundcard for home studio : many I/O and
a quality of sound is good, better than consumer cards, but less
musical than professional cards.
It use a Via Envy24ht chipset as ice1724 soundcard, Sigmatel
stac9640 ADC/DAC for the analog I/O as Prodigy192, and Atmel ak4114
for S/PDIF as ESI Julia.
Is working : the 8 analog outputs, the analog inputs 1&2, the mic
input 1, the coaxial & optical digital outputs.
Signed-off-by: Clement Guedez <klem.dev@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch supports Audiotrack 7.1 XT.
7.1XT is almost same hardware as 7.1LT. so using 7.1 LT's code.
Signed-off-by: Toshimune Konno <heitouk@nifty.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added the (experimental) support of M-Audio Audiophile 192 board.
Currently, the analog and the digital playbacks seem working fine.
The inputs seem not working as far as I've tested yet.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Enable the analog loopback of the Revolution 5.1 card.
This patch adds support for the PT2258 volume controller and modifies
the Revolution 5.1 driver to make use of this facility. This allows
to control the analog loopback of the card.
Signed-off-by: Jochen Voss <voss@seehuhn.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Enable capture from line-in and CD on the Revolution 5.1 card.
This patch adds support for switching between the 5 input channels of
the AK5365 ADC and modifies the Revolution 5.1 driver to make use of
this facility. Previously the capture channel was fixed to channel 0
(microphone on the Revolution 5.1 card).
Signed-off-by: Jochen Voss <voss@seehuhn.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fix IRQ flags for PCI devices.
The shared IRQs for PCI devices shouldn't be allocated with
IRQF_DISABLED. Also, when MSI is enabled, IRQF_SHARED shouldn't
be used.
The patch removes unnecessary cast in request_irq and free_irq,
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Remove IPGA volume controls and merge the IPGA range to ADC volume
controls. These two volumes are not really independent but connected
simply in different ranges 0-0x7f and 0x80-max. It doesn't make sense
to provide two controls.
Since both 0x7f and 0x80 specify 0dB, a hack is needed for IPGA range
to skip 0x80 (increment one) for such controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added the dB scale information to each board support code of ice1724 driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added the dB scale information for native digital volumes of ice1712 driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
- Clean up the code in AK4xxx-ADDA i2c code.
- Fix capture gain controls for AK5365
- Changed the static table for DAC/ADC mixer labels to use
structs
- Implemented TLV entries for each AK codec
The volumes in AK4524, AK4528 and AK5365 are corrected with
a table to be suitable for dB conversion.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Complete the AK5365 support.
This adds a boolean control to toggle the soft mute feature of the
AK5365 chip.
Signed-off-by: Jochen Voss <voss@seehuhn.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Enable capture support for the M-Audio Revolution 5.1 card,
by registering the ADC with ALSA.
Signed-off-by: Jochen Voss <voss@seehuhn.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fixed 'section mismatch' errors in ALSA PCI drivers:
- removed invalid __devinitdata from pci id tables
- fix/remove __devinit of functions called in suspend/resume
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fix the driver string name for Terratec Aureon 7.1 Universe
to fit in 15 letters to avoid the overflow.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds stereo controls to revo cards by making the ak4xxx
driver mixers configurable from the card driver.
Signed-off-by: Jani Alinikula <janialinikula@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
To permit use, in ice1712, of the mpu401 info flags recently added to
mpu401_uart, adds info_flags in snd_ice1712_card_info so that additional
flags can be set, if desired. 'MPU401_INFO_INTEGRATED' is always set with
the ice1712. The flags are passed on to snd_mpu401_uart_new().
_INFO_OUTPUT is set for DMX6fire mpu2.
Signed-off-by: Alan Horstmann <gineera@aspect135.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for useable front audio channels,
user controllable headphone channel and optical output.
From: Anho Ki
Signed-off-by: Matt Taylor <mwtaylor@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Consumer AC97 is not used by the Terratec DMX6fire, but eeprom bit indicates
it is; change the stored value to disable failing consumer mode.
Signed-off-by: Alan Horstmann <gineera@aspect135.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change the 5th argument of snd_mpu401_uart_new() to bit flags
instead of a boolean. The argument takes bits that consist of
MPU401_INFO_XXX flags.
The callers that used the value 1 there are replaced with
MPU401_INFO_INTEGRATED.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Patch provides for the ice1712 card driver to overwrite the midi port name
string given by default in mpu401_uart, with one specified in
snd_ice1712_card_info.
Signed-off-by: Alan Horstmann <gineera@aspect135.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There's no reason for #include'ing linux/dma-mapping.h more than once.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds a mixer control which allows the user to switch the Aux
playback between the internal Aux jack, Wavetable, and Rear Line-In on
Aureon Universe cards.
For switching, a PCA9554 (8-line GPIO with I2C interface) and a 74HC4052
(dual 4-way mux/demux) are used. Output 0 and 1 of the PCA9554 are
connected to the select pins of the 74HC4052. The I2C interface of the
PCA9554 is connected to the card's internal SPI bus which is also used
to control the WM8770 and CS8415. SPI and I2C on the same lines...
To communicate with the PCA9554 the WM8770 and CS8415 are disabled and
an I2C Stop Condition is generated before the Start Condition (needed
for synchronisation because other SPI traffic appear to confuse the
PCA9554). Then a normal I2C data transfer takes place. Programming must
be done ridiculously slow; in theory, 4.7us is the minimum delay time
for normal-speed I2C according to the datasheet, but even with 10us
switching was unreliable. The Windows driver from Terratec does the
programming very slowly, too (checked with an oscilloscope).
PCA9554 datasheet:
http://www.semiconductors.philips.com/acrobat/datasheets/PCA9554_9554A_6.pdf
74HC4052 datasheet:
http://www.semiconductors.philips.com/acrobat/datasheets/74HC_HCT4052_4.pdf
Signed-off-by: Maximilian Rehkopf <otakon@gmx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I have just discovered I made an error in the register value set in 'Limit
dmx6fire to 6 dacs' patch (bug1472). The value set should be '2a' not '0a'
as in the original patch, which unintentionally disables the 2nd MPU 401
UART.
Signed-off-by: Alan Horstmann <gineera@aspect135.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace all occurences of 0xff.. in calls to function pci_set_dma_mask()
and pci_set_consistant_dma_mask() with the corresponding DMA_xBIT_MASK from
linux/dma-mapping.h.
Signed-off-by: Matthias Gehre <M.Gehre@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch introduces the DMA_28BIT_MASK constant in dma-mapping.h
ALSA drivers using this mask are changed to use the new constant.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Jaroslav Kysela <perex@suse.cz>
Modules: ICE1712 driver
This patch makes two needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ICE1712 driver
I posted this patch to bug 1806 a while back, and have been awaiting a
reply or commit. It currently reports the Locked/No Signal text
backwards in envy24control, since i was using an older version of
envy24control when I wrote the original code. The Locked/No Signal test
was recently reversed in envy24control cvs, so the test in my code needs
to be reversed as well. Here is the patch, once again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ICE1712 driver
Change the value written to hardware configuration register of envy24 chip
in the case of Terratec DMX6fire to restrict the active ADCs & DACs to 6.
Also add the dxr_enable module option to eventually leave the old behaviour
when user requests.
Signed-off-by: Alan Horstmann <gineera@aspect135.co.uk>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
