Although reporting of benign GART TLB errors is disabled in
__mcheck_cpu_apply_quirks, those are still being logged, and, as a
result, trip up amd64_edac. Pull up reporting check so that machines
with loaded edac module bail out early and don't spit fragments into
dmesg.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
drivers/edac/amd64_edac.c: In function 'amd64_edac_init':
drivers/edac/amd64_edac.c:2840: warning: 'ret' may be used uninitialized in this function
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The routine does the reverse mapping of the error address of a CECC back
to the node id, DRAM controller and chip select of the DIMM which caused
the error. We should lookup the channel using the syndromes _only_ when
the DCTs are ganged so fix that.
Also, add an early exit when there's an error while scanning for the
csrow thus decreasing indentation levels for better readability.
Finally, fixup comments.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Instead of using the whole syndrome tables for channel decoding, use a
set of eigenvectors with which the tables can be generated to search for
the syndrome in error. The algorithm operates independently of symbol
size and can be used for both x4 and x8 syndromes.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The .probe_valid_hardware low_ops member checked whether the DCTs are in
DDR3 mode and bailed out if so. Now that all the needed changes for DDR3
support is in place, remove it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Instead of using deeply-nested conditionals for dumping the DIMM type in
debug mode, add a strings array of the supported DIMM types.
This is useful in cases where an edac driver supports multiple DRAM
types and is only defined in debug builds.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Add cs mode to cs size mapping tables for DDR2 and DDR3 and F10
and all K8 flavors and remove klugdy table of pseudo values. Add a
low_ops->dbam_to_cs member which is family-specific and replaces
low_ops->dbam_map_to_pages since the pages calculation is a one liner
now.
Further cleanups, while at it:
- shorten family name defines
- align amd64_family_types struct members
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Do not read DCLR[01] again since this is done in
amd64_read_mc_registers() earlier. There can be more than two physical
DIMMs present so clamp the channels value to max 2. Also, do not report
DCT data width - it is also done earlier.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Extend f10_debug_display_dimm_sizes to dump the logical DIMMs
configuration on K8 revF too. Remove the ganged arg since we print the
DCT operating mode (ganged vs unganged) earlier.
Also, DCT csrow configuration is relevant therefore dump it as
KERN_DEBUG instead of only on debug builds. Remove misleading DIMM
output since there's no reliable way of mapping of chip selects to
actual physical DIMMs.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Carve out the register-specific debug statements into a separate
function, clarify meanings of the single bitfields in the register,
remove irrelevant output and macros.
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Add a pci config read wrapper for signaling pci config space access
errors instead of them being visible only on a debug build. This is
important on amd64_edac since it uses all those pci config register
values to access the DRAM/DIMM configuration of the nodes.
In addition, the wrapper makes a _lot_ (look at the diffstat!) of
error handling code superfluous and improves much of the overall code
readability by removing error handling details out of the way.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Unify almost identical code into one function and remove NUMA-specific
usage (specifically cpumask_of_node()) in favor of generic topology
methods.
Remove unused defines, while at it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
cpumask_t -> struct cpumask, and don't put one on the stack. (Note: this
is actually on the stack unless CONFIG_CPUMASK_OFFSTACK=y).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Do not shift the TOP_MEM and TOP_MEM2 values by 23 but rather save the
whole 64-bit value read from the MSR. Although the TOP_MEM/TOP_MEM2 bits
are only a subset of the 64bit register, the values are correct since
the remaining bits are Read-As-Zero and no shifting is needed.
Also, cleanup DRAM base/limit debug output.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Make debug info formulations about the DRAM and DCT configuration of the
machine more human readable.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
In amd64_edac_init(void) in amd64_edac.c, cache_k8_northbridges() is
called before pci_register_driver. If it fails, should exit with err
directly.
Signed-off-by: Li Hong <lihong.hi@gmail.com>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Allow csrows to properly initialize when the topology only has active
channels on 2 and 3. This new check allows proper detection and
initialization in this topology. Only checking the first mrt that
represented channels 0 and 1 is not sufficient.
I also fixed up the related debug information path. I can submit as a 2nd
patch if needed.
Signed-off-by: Keith Mannthey <kmannth@us.ibm.com>
Acked-by: Aristeu Rozanski <aris@ruivo.org>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When building without CONFIG_PCI the edac_pci_idx variable is unused,
causing a build-time warning. Wrap the variable in #ifdef CONFIG_PCI,
just like the rest of the PCI support.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The i5400 EDAC driver has several bugs with chip-select row computation
which most likely lead to bugs in detailed error reporting. Attempts to
contact the authors have gone mostly unanswered so I am presenting my diff
here. I do not subscribe to lkml and would appreciate being kept in the
cc.
The most egregious problem was miscalculating the addresses of MTR
registers after register 0 by assuming they are 32bit rather than 16.
This caused the driver to miss half of the memories. Most motherboards
tend to have only 8 dimm slots and not 16, so this may not have been
noticed before.
Further, the row calculations multiplied the number of dimms several
times, ultimately ending up with a maximum row of 32. The chipset only
supports 4 dimms in each of 4 channels, so csrow could not be higher than
4 unless you use a row per-rank with dual-rank dimms. I opted to
eliminate this behavior as it is confusing to the user and the error
reporting works by slot and not rank. This gives a much clearer view of
memory by slot and channel in /sys.
Signed-off-by: Jeff Roberson <jroberson@jroberson.net>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an atomic notifier which ensures proper locking when conveying
MCE info to EDAC for decoding. The actual notifier call overrides a
default, negative priority notifier.
Note: make sure we register the default decoder only once since
mcheck_init() runs on each CPU.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <20091003065752.GA8935@liondog.tnic>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When injecting DRAM ECC errors (F3xBC_x8), EccVector[15:0] is a bitmask
of which bits should be error injected when written to and holds the
payload of 16-bit DRAM word when read, respectively.
Add /sysfs members to show the DRAM ECC section/word/vector.
Fail wrong injection values entered over /sysfs instead of truncating
them.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
On Fam10h and above, F1x[1, 0][7C:40] are DRAM Base/Limit registers
which specify the destination node of a DRAM address. Those address
boundaries are being extracted into ->dram_base[] and ->dram_limit[].
Correct the extraction masks to match the respective address bits.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Different processor families support a different number of chip selects.
Handle this in a family-dependent way with the proper values assigned at
init time (see amd64_set_dct_base_and_mask).
Remove _DCSM_COUNT defines since they're used at one place and originate
from public documentation.
CC: Keith Mannthey <kmannth@us.ibm.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
This allows the errors to be further decoded and mapped to csrows.
Tested with ECC debug dimms and an Rev F cpu based system.
Signed-off-by: Keith Mannthey <kmannth@us.ibm.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The check when DRAM interleaving is enabled should be done against the
pvt->dram_IntlvSel field and not against the ->dram_limit.
Simplify first loop and fixup printk formatting while at it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The pvt->dram_IntlvEn saves the 3 "Interleave Enable" bits already
right-shifted by 8 so the check in find_mc_by_sys_addr() by shifting the
values to the left 8 bits is wrong.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
K8 DRAM base and limit addresses from F1x40 +8*i and F1x44 + 8*i, where
i in (0..7) are both bits 39-24 and therefore the shifting should be
done by 24 and not by 8.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Allocate memory statically for 8-node machines max for simplicity
instead of relying on MAX_NUMNODES which is 0 on !CONFIG_NUMA builds.
Spotted by Jan Beulich.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
This converts the MCE decoding logic into a standalone config
option which can be built-in or a module, the first one being the
default for MCEs happening early on in the boot process.
This, beyond being separated in a cleaner way, also saves RAM by
making the decoding logic modular.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andi Kleen <andi@firstfloor.org>
LKML-Reference: <20091002133148.GD28682@aftab>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Make decoding of MCEs happen only on AMD hardware by registering a
non-default callback only on CPU families which support it.
While looking at the interaction of decode_mce() with the other MCE
code i also noticed a few other things and made the following
cleanups/fixes:
- Fixed the mce_decode() weak alias - a weak alias is really not
good here, it should be a proper callback. A weak alias will be
overriden if a piece of code is built into the kernel - not
good, obviously.
- The patch initializes the callback on AMD family 10h and 11h.
- Added the more correct fallback printk of:
No support for human readable MCE decoding on this CPU type.
Transcribe the message and run it through 'mcelog --ascii' to decode.
On CPUs that dont have a decoder.
- Made the surrounding code more readable.
Note that the callback allows us to have a default fallback -
without having to check the CPU versions during the printout
itself. When an EDAC module registers itself, it can install the
decode-print function.
(there's no unregister needed as this is core code.)
version -v2 by Borislav Petkov:
- add K8 to the set of supported CPUs
- always build in edac_mce_amd since we use an early_initcall now
- fix checkpatch warnings
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andi Kleen <andi@firstfloor.org>
LKML-Reference: <20091001141432.GA11410@aftab>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Module edac_core.ko uses call_rcu() callbacks in edac_device.c, edac_mc.c
and edac_pci.c.
They all use a wait_for_completion() scheme, but this scheme it not 100%
safe on multiple CPUs. See the _rcu_barrier() implementation which
explains why extra precausion is needed.
The patch adds a comment about rcu_barrier() and as a precausion calls
rcu_barrier(). A maintainer needs to look at removing the
wait_for_completion code.
[dougthompson@xmission.com: remove the wait_for_completion code]
Signed-off-by Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A driver for the Intel 3200 and 3210 memory controllers. It has only had
light testing so far, and currently makes no attempt to decode error
addresses at anything finer than csrow granularity.
Signed-off-by: Jason Uhlenkott <juhlenko@akamai.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the function resource_size, which reduces the chance of introducing
off-by-one errors in calculating the resource size.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct resource *res;
@@
- (res->end - res->start) + 1
+ resource_size(res)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the Freescale MPC83xx memory controller to the existing
driver for the Freescale MPC85xx memory controller. The only difference
between the two processors are in the CS_BNDS register parsing code, which
has been changed so it will work on both processors.
The L2 cache controller does not exist on the MPC83xx, but the OF
subsystem will not use the driver if the device is not present in the OF
device tree.
I had to change the nr_pages calculation to make the math work out. I
checked it on my board and did the math by hand for a 64GB 85xx using 64K
pages. In both cases, nr_pages * PAGE_SIZE comes out to the correct
value.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on Kumar's new compatible types patch, add P2020 into MPC85xx EDAC
compatible lists so that EDAC can recognize P2020 meomry controller and L2
cache controller and export the relevant fields to sysfs.
EDAC MPC85xx DDR3 support is needed if DDR3 memory stick is installed on a
P2020DS board so that EDAC core can recognize DDR3 memory type.
Signed-off-by: Yang Shi <yang.shi@windriver.com>
Acked-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The old code was using smp_call_function_many which skips the current
cpu if it is in the supplied cpumask. Switch to the rdmsr_on_cpus()
interface which takes care of that.
In addition, add get_cpus_on_this_dct_cpumask helper which computes a
cpumask of all the cores on a node and thus on a DCT.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Simplify the procedure by checking if there is any DIMM in each channel.
This patch will fix the bugs such as when there is no DIMMs under
certain node, two DIMMs in the same channel, and only one DIMM in each
channel of the node.
Borislav: minor fixups
Signed-off-by: Wan Wei <wanwei@mail.dawning.com.cn>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
