The documentation for the S3C6410 CPU voltage scaling is rather
unclear, with omitted values for several speed settings. Originally
the code was using only quoted values, resulting in some fairly odd
settings. The S3C6410 is also unusual in that the both the maximum
and minimum voltages quoted scale as the frequency rises, rather
than just the minimum voltage.
Clean this up a bit by always using the specified typical settings
as the minimum voltage (ignoring any specified minimum voltage) in
order to avoid running near the edge of the processor capabilities.
Also use the next quoted maximum voltages rather than the typical
voltages where no maximum voltage is quoted, allowing operation on
a greater range of systems.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Currently the transition latency reported by the S3C64xx cpufreq
driver includes both the time for the CPU to reclock itself and
the time for a regulator to change voltage. This means that if
a regulator is not in use then the transition latency reported
is excessively high.
In future the regulator API will be extended to report latencies
so the driver will be able to query the performance of a given
regulator.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This provides symmetry with the voltage based checks done for the
regulator.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
DVDD is supplied by supplies derived from the PMIC, AVDD and PVDD are
supplied from the main wall supply on the base board which runs at
5V. No option is currently supported for running without a PMIC card,
the assumption is that the regulator API will be built out when no
soft PMIC card is in use.
To ease merge issues since this uses the newly added dev_name supply
configuration from the regulator API (currently in -next only) the
fixed voltage regulator is ifdefed out when the regulator API is not
enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Better using standard interfaces to enable/disable bluetooth
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add lcd and backlight device definition. The pwm backlight stuff does
not allow to really set maximum pwm as with my custom driver but it's
better to use standard driver instead of out of tree driver.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
[ben-linux@fluff.org: tidy header]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix mach-n30.c to use the s3c_i2c0_set_platdata() call to register the
platform data with the system to get rid of any reliance on having a real
device structure available in memory.
Since s3c_i2c0_set_platdata() copies the data, mark the original as
__initdata so it is thrown away.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The AT2440EVB should not be changing the s3c_device_sdi.name as this is
part of the initialisation process done by the CPU detection process
and actually present in arch/arm/plat-s3c24xx/s3c24xx.c.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The mach-h1940.c file was using s3c_device_ where it really should be
calling these local definitions h1940_device to ensure they are not
mistaken for real s3c_devices when the device change is done.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We inted to re-organise the plat-s3c/plat-s3c24xx/plat-s3c64xx into a
more generic plat-samsung with less code in the other plat- directories
to make it easier to port new devices and try and clear up some of the
naming issues with newer devices.
Start by creating a small arch/arm/plat-samsung with no actuall code in
so we can move items in as we process them.
Add this to arch/arm to allow it to build things once support is added.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
arch/alpha/kernel/vmlinux.lds.S uses it:
arch/alpha/kernel/vmlinux.lds:241: undefined symbol `THREAD_SIZE' referenced in expression
Seems to have been caused by
commit 9d93f00580
Author: Geoffrey Thomas <geofft@ksplice.com>
AuthorDate: Thu Sep 24 10:36:26 2009 -0400
Commit: Linus Torvalds <torvalds@linux-foundation.org>
CommitDate: Thu Sep 24 17:16:22 2009 -0700
alpha: Clean up linker script using new linker script macros.
Note that .data.page_aligned and .data.cacheline_aligned are now after
_data; it was probably a bug that they were before it.
Also, some explicit ALIGN(8)'s between various initcall sections were
removed; this should be harmless as the implicit alignment of
initcall_t was already 8.
Cc: Geoffrey Thomas <geofft@ksplice.com>
Cc: Tim Abbott <tabbott@ksplice.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a bug in
commit ba0a6c9f6f
Author: Peter Zijlstra <a.p.zijlstra@chello.nl>
AuthorDate: Wed Sep 23 15:57:03 2009 -0700
Commit: Linus Torvalds <torvalds@linux-foundation.org>
CommitDate: Thu Sep 24 07:21:01 2009 -0700
fcntl: add F_[SG]ETOWN_EX
In asm-generic/fcntl.h, F_SETOWN_EX and F_GETLK64 both have value 12, and
F_GETOWN_EX and F_SETLK64 both have value 13.
Reported-by: "Joseph S. Myers" <joseph@codesourcery.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Andreas Schwab <schwab@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adjust OMAP3 frequency transition latency from 10,000,000uS to a more
reasonable 300,000uS. This causes ondemand and conservative governors to
sample CPU load more often resulting in more responsive behavior.
Tested on Android 2.6.29; using this value and conservative governor, CORE
power consumption on Zoom2 was comparable to the old and unresponsive
10,000,000uS value while UI responsiveness was greatly improved.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86/PCI: Adjust GFP mask handling for coherent allocations
PCI ASPM: fix oops on root port removal
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: pasemi_defconfig update
powerpc: 2.6.32 update of defconfigs for embedded 6xx/7xxx, 8xx, 8{3,5,6}xxx
powerpc/8xxx: enable IPsec ESP by default on mpc83xx/mpc85xx
powerpc/83xx: Fix u-boot partion size for MPC8377E-WLAN boards
powerpc/85xx: Fix USB GPIOs for MPC8569E-MDS boards
powerpc/82xx: kmalloc failure ignored in ep8248e_mdio_probe()
powerpc/85xx: sbc8548 - fixup of PCI-e related DTS fields
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, amd-ucode: Check UCODE_MAGIC before loading the container file
x86: Fix error return sequence in __ioremap_caller()
x86: Add Phoenix/MSC BIOSes to lowmem corruption list
This patch updates defconfig to enable options needed to properly
boot OMAP3 pandora board. It also enables MMC, OTG, GPIO LEDs,
TWL4030 GPIO and sound drivers.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some drivers have dependencies on this, and therefore should be
enabled.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The host port power is enabled by driving the nEN_USB_PWR low as stated in
the comment. This fix is originally from Steve Sakoman <steve@sakoman.com>.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The original TWL4030 keypad driver from linux-omap used KEY()
macro defined as (col, row), but while it was merged upstream
it was changed to use matrix keypad infrastructure, which uses
(row, col) format. Update the keymap in board file to match
layout of mainline driver.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The patch provides the following fixes:
- keep kernel small enough to boot with standard tools,
- ensure compatibility with both new and legacy distros,
- turn on support for recently added or fixed hardware features.
Created and tested against linux-2.6.32-rc5.
Signed-off-by: Janusz Krzysztofik <jkrzysz@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With CONFIG_PM=y, the omapfb/lcdc device on Amstrad Delta, after initially
starting correctly, breaks with the following error messages:
omapfb omapfb: resetting (status 0xffffff96,reset count 1)
...
omapfb omapfb: resetting (status 0xffffff96,reset count 100)
omapfb omapfb: too many reset attempts, giving up.
Looking closer at this I have found that it had been broken almost 2 years ago
with commit 2418996e3b100114edb2ae110d5d4acb928909d2, PM fixes for OMAP1.
The definite reason for broken omapfb/lcdc behavoiur in PM mode
appeared to be ARM_IDLECT1:IDLIF_ARM (bit 6) put into idle regardless of LCD
DMA possibly running. The bit were set based on return value of the
omap_dma_running() function that did not check for dedicated LCD DMA
channel status. The patch below fixes this.
Note that the hardcoded register value will be fixed during the next merge
cycle to use OMAP_LCDC_ defines. Currently the OMAP_LCDC_ defines are local
to drivers/video/omap/lcdc.c, so let's not start moving those right now.
Created against linux-2.6.32-rc6
Tested on Amstrad Delta
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
pasemi_defconfig hasn't been updated for a year.
Mostly a refresh of defaults, but this also disables 64K pages.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use the resource_size function instead of manually calculating the
resource size. This reduces the chance of introducing off-by-one errors
and actually fixes one in mailbox.c.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The bug could cause irq enable bit of one DMA channel is
cleared/set unexpectedly when 2 (or more) drivers are calling
omap_request_dma()/omap_free_dma() simultaneously
Signed-off-by: Fei Yang <AFY095@motorola.com>
Signed-off-by: Tao Hu <taohu@motorola.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use a definition for the cmpxchg SWI instead of hard-coding the number.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
We need to free the buff and lli nodes if the buffer queue is
not CIRCULAR.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
buffdone callback should be called per buffer request with pointer
to the latest serviced request.
'next' should point to the one next to currently active.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Some devices don't seem to work if the source and desitnation transfer
widths are not same. For example, SPI dma xfers, with 8bits/word,
don't work without this patch.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Replace s3c64xx_dma_tcirq and s3c64xx_dma_errirq with the common
s3c64xx_dma_buffdone.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Ensure the DMA buffer points are not updated from
another source during the process of enquing a buffer.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
[ben-linux@fluff.org: Updated patch comment]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The recent changes to arch/arm/mach-s3c6400/include/mach/dma.h have
left an out of date comment in there as well as accidentally changing
the type of the function.
Fix the commit 54489cd46a
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch removes the duplicated s3c_dma_has_circular() definition and so fixes
compilation for S3C64xx.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The WM835x has some GPIOs on it, allocate some space so we can use
them with gpiolib.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
When used with the WM1190-EV1 board we can use the internal pull up
resistor of the CPU to provide the required pull for the IRQ line.
Without this interrupts from the WM835x don't work in the default
WM1190-EV1 hardwaer configuration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc: Move of_set_property_mutex acquisition outside of devtree_lock grab.
sparc64: replace parentheses in pmul()
sparc64: Add a comment about why we only use certain memory barriers these days.
* 'sh/for-2.6.32' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Replace old style lock initializer
sh: Account for cache aliases in flush_icache_range()
sh: unwinder: Fix up invalid PC refetch in dwarf unwinder.
serial: sh-sci: disable callback typo fix
SPIN_LOCK_UNLOCKED is deprecated. Use __SPIN_LOCK_UNLOCKED instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The icache may also contain aliases so we must account for them just
like we do when manipulating the dcache. We usually get away with
aliases in the icache because the instructions that are read from memory
are read-only, i.e. they never change. However, the place where this
bites us is when the code has been modified.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
