On Yukon FE, occasional hardware receive checksum errors are seen.
An early indication of the problem is single bit differences in the two
checksum engines. Use this as a detection mechanism to turn off Rx
checksumming.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add a wc_enabled flag in the myri10ge_priv instead of relying
on mtrr >= 0.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Do not use 4k rdma request on SGI TIOCE chipset since this
bridge does not support it.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Allocate a specific page and use pci_map_page for dma test instead
of relying on another existing buffer.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix a missing error check in myri10ge_allocate_rings() and set status
to -ENOMEM before all actual allocations so that the error path returns
what it should.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
CC [M] drivers/net/netxen/netxen_nic_hw.o
drivers/net/netxen/netxen_nic_hw.c: In function 'netxen_nic_hw_resources':
drivers/net/netxen/netxen_nic_hw.c:231: warning: format '%llx' expects type 'long long unsigned int', but argument 2 has type 'dma_addr_t'
drivers/net/netxen/netxen_nic_hw.c:250: warning: format '%llx' expects type 'long long unsigned int', but argument 2 has type 'dma_addr_t'
u64 is unsigned long so the cast to u64 will result in a warning on the
printf arguments for 64-bit builds. So cast to unsigned long long instead.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch sets avoid_D3 for BIOSes known to be broken. Said BIOSes fail
at PXE boot if the chip is in power state D3.
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some platform devices are driven without driver attached, so managed
resources can be acquired without driver attached. Make sure such
resources are released by calling devres_release_all() in
device_del().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Commit 721449bf0d added support for using the
ADMA notifier bits to determine which commands to check for completion.
However there have been reports that this causes command timeouts in certain
cases. This is still being investigated. In addition, apparently the notifiers
won't work if ADMA is disabled on the other port as a result of an ATAPI device
being connected, and we don't handle this case properly.
For now, just restore the previous behavior of checking all active commands
to see if they are complete, without relying on the notifiers.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Recently I got my hands on nVidia's MCP61 PM-AM board, and
it contains IDE chip configured by BIOS with only primary
channel enabled. This confuses code which probes for
device DMA capabilities - it gets 0x60 (happy duplex
device) from primary channel BMDMA, but 0xFF (nobody here)
from secondary channel BMDMA. Due to this code then believes
that chip is simplex. I do not address this problem in
my patch, as I'm not sure how to handle this. Probably
ata_pci_init_one should have bitmap of enabled/possible
interfaces instead of their count, but it looks like
quite intrusive change, and maybe we do not care - for device
with only one channel simplex and regular DMA engines are
same.
But making device simplex pointed out that support for
DMA on simplex devices is currently broken - ata_dev_xfermask
tests whether device is simplex and if it is whether DMA
engine was assigned to this port. If not then it strips
out DMA bits from device. Problem is that code which assigns
DMA engine to port in ata_set_mode first detect device
mode and assigns DMA engine to channel only if some DMA
capable device was found.
And as xfermask stripped out DMA bits, host->simplex_claimed
is always NULL with current implementation.
By allowing DMA either if simplex_claimed is NULL or if it
points to current port DMA can be finally used - it gets
assigned to first port which contains any DMA capable
device.
Before:
pata_amd 0000:00:06.0: version 0.2.8
PCI: Setting latency timer of device 0000:00:06.0 to 64
ata5: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001f000 irq 14
ata6: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001f008 irq 15
scsi4 : pata_amd
ata5.00: ATAPI, max UDMA/66
ata5.00: simplex DMA is claimed by other device, disabling DMA
ata5.00: configured for PIO4
scsi5 : pata_amd
ata6: port disabled. ignoring.
ata6: reset failed, giving up
scsi 4:0:0:0: CD-ROM ATAPI DVD W DH16W1P LG12 PQ: 0 ANSI: 5
After:
pata_amd 0000:00:06.0: version 0.2.8
PCI: Setting latency timer of device 0000:00:06.0 to 64
ata5: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001f000 irq 14
ata6: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001f008 irq 15
scsi4 : pata_amd
ata5.00: ATAPI, max UDMA/66
ata5.00: configured for UDMA/33
scsi5 : pata_amd
ata6: port disabled. ignoring.
ata6: reset failed, giving up
scsi 4:0:0:0: CD-ROM ATAPI DVD W DH16W1P LG12 PQ: 0 ANSI: 5
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A while ago I modified the libata code so that drivers can return -ENOENT
for unknown ports not fiddle with the EH flags and print stuff directly.
Somewhere along the line ata_piix didn't get fully converted.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
New bad eraseblock is an event which is important enough to be printed
about.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Due to a poor choice of CRC32 seed, a node header which is all zeroes
would pass the CRC32 check. Explicitly check for this case, and treat it
as we do a CRC failure.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
x86_64 nvidia_bugs() broke when we bailed out on not finding the HPET.
However, the quirk works by checking for not finding the HPET...
Delete the nvidia_hpet_detected flag and simply test for
not finding the HPET, which is simple to do now that
acpi_table_parse returns 1 on failure.
Signed-off-by: Len Brown <len.brown@intel.com>
Classify the page data and oob buffer
and it prevents the memory fragementation (writesize + oobsize)
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When transferring/filling of the oob is finished in OOB_AUTO, we exit the loop
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
add Nokia Copyright and a credit
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
In oob functions, it is used main buffer instead of oob one. So fix it.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The PNPACPI resource flags were broken.
This would apply to re-enabling a device any-time after boot,
not just after resume from S3.
http://bugzilla.kernel.org/show_bug.cgi?id=6316
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Improve the backlight code to emulate as much as possible the power
management events, as we are unable to really power on or power off the
backlight.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Len Brown <len.brown@intel.com>
- point to the sparse webpage
- use git:// instead of rsync://
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
x86_64 nvidia_bugs() broke when we bailed out on not finding the HPET.
However, the quirk works by checking for _not_ finding the HPET...
Delete the nvidia_hpet_detected flag and simply test for
not finding the HPET, which is simple to do now that
acpi_table_parse returns 1 on failure.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Turn on interface's carrier after broadcast group is joined
RDMA/ucma: Avoid sending reject if backlog is full
RDMA/cxgb3: Fix MR permission problems
RDMA/cxgb3: Don't reuse skbs that are non-linear or cloned
RDMA/cxgb3: Squelch logging AE errors
RDMA/cxgb3: Stop EP timer when MPA exchange is aborted by peer
RDMA/cxgb3: Move QP to error on destroy if the state is IDLE
RDMA/cxgb3: Fixes for "normal close" failures
RDMA/cxgb3: Fix build on sparc64
RDMA/cma: Initialize rdma_bind_list in cma_alloc_any_port()
RDMA/cxgb3: Don't use mm after it's freed in iwch_mmap()
RDMA/cxgb3: Start ep timer on a MPA reject
IB/mthca: Fix error path in mthca_alloc_memfree()
IB/ehca: Fix sync between completion handler and destroy cq
IPoIB: Only handle async events for one port
Do netif_carrier_on() right after the IPv4 broadcast multicast group
is joined, rather than waiting for all of the initial set of multicast
group joins to finish. This allows at least IPv4 traffic to limp
along on broken fabrics where not all multicast groups can be joined.
Signed-off-by: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
lockdep found that dev->lock taken from softirq in ipv6_add_addr
is also taken in sctp_v6_copy_addrlist with softirqs enabled, so
lockup is possible.
Noticed-by: Simon Arlott <simon@arlott.org>
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
For 2.6.20 it mostly used to just not work, for 2.6.21-rc it crashes, this
seems to be down to luck (bad or good). The libata-acpi code needs to
avoid doing PCI work on non-PCI devices. This is one hack although it's
not pretty and perhaps there is a "right" way to check if a struct device
* is PCI ?
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bring defconfig, tiger_defconfig and zx1_defconfig up to date. Also
sprinkle KEXEC and KDUMP combinations around liberally so that my
usual regression test builds will see all combinations:
tiger_defconfig gets KEXEC=y, CRASH_DUMP=n
zx1_defconfig gets KEXEC=n, CRASH_DUMP=y
defconfig gets KEXEC=y, CRASH_DUMP=y
others remain at KEXEC=n, CRASH_DUMP=n
Signed-off-by: Tony Luck <tomy.luck@intel.com>
kdump_find_rsvd_region() is only called by
reserve_memory() which is in __init, so it seems that
kdump_find_rsvd_region() should also be in there.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Running ia64 through sparse gives warnings in the unwind code.
include/asm-ia64/unwind.h:84:17: error: dubious bitfield without explicit `signed' or `unsigned'
Make the bitfield explicitly unsigned.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The ptrace misses clearing the syscall trace flag.
The increased syscall overhead is retained after the trace is finished.
This case happens when strace is terminated by force.
Signed-off-by: Akiyama, Nobuyuki <akiyama.nobuyuk@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Grammatical fixes (s/freezed/frozen/)
Make some variables static
Change a C++ "//" comment to "/* ... */"
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* Kexec adds some code to arch/ia64/kernel/smp.c which needs ia64_mca_pal_base,
so the kexec patch (actually the kdump patch) declares this
per-cpu variable in include/asm-ia64/kexec.h.
* ia64_mca_pal_base is defined in arch/ia64/kernel/mca.c, so it
seems to me that it would make a lot more sense to declare it in
include/asm-ia64/mca.h.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Function pci_get_legacy_ide_irq is incorrect on ia64. It should return
irq vector instead of GSI. The fixed number 14 and 15 are just GSI.
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* Make use of spaces and tabs consistent
* Make long line < 80col
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Similar to memory error recovery, when a cache error is consumed
by a user process terminate the user instead of crashing the system.
Signed-off-by: Russ Anderson (rja@sgi.com)
Acked-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Jack Steiner noticed that duplicate TLB DTC entries do not cause a
linux panic. See discussion:
http://www.gelato.unsw.edu.au/archives/linux-ia64/0307/6108.html
The current TLB recovery code is recovering from the duplicate itr.d
dropins, masking the underlying problem. This change modifies
the MCA recovery code to look for the TLB check signature of the
duplicate TLB entry and panic in that case.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
ecryptfs uses a lock_parent() function, which I hope really locks the parents
and is not abused
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sn console driver was snagged by the use of CONFIG_DEBUG_SHIRQ!
The request_irq() immediate call to the interrupt handler caused
another attempt to lock the port lock - deadlock.
This is a patch to fix that.
Signed-off-by: Patrick Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In my previous x86_64 thread fix, I forgot to initialize thread.arch.fs in
arch_prctl. A process calling arch_prctl to set %fs would lose it on the
next context switch.
It also turns out that you can switch to a process which is in the process
of exiting and which has lost its mm. In this case, it's worse than
useless to try to call arch_prctl on the host process.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
IA64 and ARM-OABI are currently using their own version of epoll compat_
code.
An architecture needs epoll_event translation if alignof(u64) in 32 bit
mode is different from alignof(u64) in 64 bit mode. If an architecture
needs epoll_event translation, it must define struct compat_epoll_event in
asm/compat.h and set CONFIG_HAVE_COMPAT_EPOLL_EVENT and use
compat_sys_epoll_ctl and compat_sys_epoll_wait.
All 64 bit architecture should use compat_sys_epoll_pwait.
[sfr: restructure and move to fs/compat.c, remove MIPS version
of compat_sys_epoll_pwait, use __put_user_unaligned]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[Bluetooth] Fix socket locking in hci_sock_dev_event()
hci_sock_dev_event() uses bh_lock_sock() to lock the socket lock.
This is not deadlock-safe against locking of the same socket lock in
l2cap_connect_cfm() from softirq context. In addition to that,
hci_sock_dev_event() doesn't seem to be called from softirq context,
so it is safe to use lock_sock()/release_sock() instead.
The lockdep warning can be triggered on my T42p simply by switching
the Bluetooth off by the keyboard button.
=================================
[ INFO: inconsistent lock state ]
2.6.21-rc2 #4
---------------------------------
inconsistent {in-softirq-W} -> {softirq-on-W} usage.
khubd/156 [HC0[0]:SC0[0]:HE1:SE1] takes:
(slock-AF_BLUETOOTH){-+..}, at: [<e0ca5520>] hci_sock_dev_event+0xa8/0xc5 [bluetooth]
{in-softirq-W} state was registered at:
[<c012d1db>] mark_lock+0x59/0x414
[<e0cef688>] l2cap_connect_cfm+0x4e/0x11f [l2cap]
[<c012dfd7>] __lock_acquire+0x3e5/0xb99
[<e0cef688>] l2cap_connect_cfm+0x4e/0x11f [l2cap]
[<c012e7f2>] lock_acquire+0x67/0x81
[<e0cef688>] l2cap_connect_cfm+0x4e/0x11f [l2cap]
[<c036ee72>] _spin_lock+0x29/0x34
[<e0cef688>] l2cap_connect_cfm+0x4e/0x11f [l2cap]
[<e0cef688>] l2cap_connect_cfm+0x4e/0x11f [l2cap]
[<e0ca17c3>] hci_send_cmd+0x126/0x14f [bluetooth]
[<e0ca4ce4>] hci_event_packet+0x729/0xebd [bluetooth]
[<e0ca205b>] hci_rx_task+0x2a/0x20f [bluetooth]
[<e0ca209d>] hci_rx_task+0x6c/0x20f [bluetooth]
[<c012d7be>] trace_hardirqs_on+0x10d/0x14e
[<c011ac85>] tasklet_action+0x3d/0x68
[<c011abba>] __do_softirq+0x41/0x92
[<c011ac32>] do_softirq+0x27/0x3d
[<c0105134>] do_IRQ+0x7b/0x8f
[<c0103dec>] common_interrupt+0x24/0x34
[<c0103df6>] common_interrupt+0x2e/0x34
[<c0248e65>] acpi_processor_idle+0x1b3/0x34a
[<c0248e68>] acpi_processor_idle+0x1b6/0x34a
[<c010232b>] cpu_idle+0x39/0x4e
[<c04bab0c>] start_kernel+0x372/0x37a
[<c04ba42b>] unknown_bootoption+0x0/0x202
[<ffffffff>] 0xffffffff
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Also PTRACE_OLDSETOPTIONS should be accepted, as done by kernel/ptrace.c
and forced by binary compatibility. UML/32bit breaks because of this -
since it is wise enough to use PTRACE_OLDSETOPTIONS to be binary compatible
with 2.4 host kernels.
Until 2.6.17 (commit f0f2d6536e) we had:
default:
return sys_ptrace(request, pid, addr, data);
Instead here we have:
case PTRACE_GET_THREAD_AREA:
case ...:
return sys_ptrace(request, pid, addr, data);
default:
return -EINVAL;
This change was a style change - when a case is added, it must be
explicitly tested this way. In this case, not enough testing was done.
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
