Drain the MAC TX fifos when a port goes down.
Back pressure might otherwise occur, leading to both
ports of the same adapter to hang.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Override the mac index computation for the gen2 adapter,
as each port is expected to use index 0.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the HW SMT table initialization to avoid random
mss miscomputations for offload connections.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use request_firmware() to load the phy's EDC programmation
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't always see the link status update interrupt
when we come out of reset and the peer is up.
Check and report the link status right before enabling interrupts.
Also fix LED settings, to get a consistent link status.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Max packet size is not the only field in T3C's High Water Mark register.
Mask the register to access this field.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2 phys are were not getting the Global Tx disable bit set
when powered down, leading to an inconsistent link state
on peer.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing SUPPORTED_TP flag.
Update FW version checking.
Do the full initialization even if the FW version is unknown,
it might help catching further issues.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the r6040 device IRQ line is shared we will enter the driver
interrupt service routine, mask off the device interrupt enable
register (MIER) and return with IRQ_NONE, we would then leave the
device with interrupts disabled, this patch fixes that issue.
Reported-by: Steve Holland <sdh4@iastate.edu>
Signed-off-by: Joe Chou <joe.chou@rdc.com.tw>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pawel Staszewski wrote:
<blockquote>
Some time ago i report this:
http://bugzilla.kernel.org/show_bug.cgi?id=6648
and now with 2.6.29 / 2.6.29.1 / 2.6.29.3 and 2.6.30 it back
dmesg output:
oprofile: using NMI interrupt.
Fix inflate_threshold_root. Now=15 size=11 bits
...
Fix inflate_threshold_root. Now=15 size=11 bits
cat /proc/net/fib_triestat
Basic info: size of leaf: 40 bytes, size of tnode: 56 bytes.
Main:
Aver depth: 2.28
Max depth: 6
Leaves: 276539
Prefixes: 289922
Internal nodes: 66762
1: 35046 2: 13824 3: 9508 4: 4897 5: 2331 6: 1149 7: 5
9: 1 18: 1
Pointers: 691228
Null ptrs: 347928
Total size: 35709 kB
</blockquote>
It seems, the current threshold for root resizing is too aggressive,
and it causes misleading warnings during big updates, but it might be
also responsible for memory problems, especially with non-preempt
configs, when RCU freeing is delayed long after call_rcu.
It should be also mentioned that because of non-atomic changes during
resizing/rebalancing the current lookup algorithm can miss valid leaves
so it's additional argument to shorten these activities even at a cost
of a minimally longer searching.
This patch restores values before the patch "[IPV4]: fib_trie root
node settings", commit: 965ffea43d from
v2.6.22.
Pawel's report:
<blockquote>
I dont see any big change of (cpu load or faster/slower
routing/propagating routes from bgpd or something else) - in avg there
is from 2% to 3% more of CPU load i dont know why but it is - i change
from "preempt" to "no preempt" 3 times and check this my "mpstat -P ALL
1 30"
always avg cpu load was from 2 to 3% more compared to "no preempt"
[...]
cat /proc/net/fib_triestat
Basic info: size of leaf: 20 bytes, size of tnode: 36 bytes.
Main:
Aver depth: 2.44
Max depth: 6
Leaves: 277814
Prefixes: 291306
Internal nodes: 66420
1: 32737 2: 14850 3: 10332 4: 4871 5: 2313 6: 942 7: 371 8: 3 17: 1
Pointers: 599098
Null ptrs: 254865
Total size: 18067 kB
</blockquote>
According to this and other similar reports average depth is slightly
increased (~0.2), and root nodes are shorter (log 17 vs. 18), but
there is no visible performance decrease. So, until memory handling is
improved or added parameters for changing this individually, this
patch resets to safer defaults.
Reported-by: Pawel Staszewski <pstaszewski@itcare.pl>
Reported-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Tested-by: Pawel Staszewski <pstaszewski@itcare.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check that network interface is running before changing its MAC address.
Otherwise, rxch is accessed when it's NULL - causing a kernel oops.
Moreover, check that the new MAC address is valid.
Signed-off-by: Pablo Bitton <pablo.bitton@gmail.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Tested-by: Chaithrika U S <chaithrika@ti.com>
[tested on DM6467 EVM]
Signed-off-by: David S. Miller <davem@davemloft.net>
The igb driver was defaulting to using the lock for pci-e function 0 for
all of the phys due to the fact that the lan id was not being set prior to
initialization. This change makes it so that the function id is set prior
to checking for the phy id.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can reclaim transmitted skbs to use in the receive path, so-called
skb recycling support.
Also reorder ucc_geth_poll() steps, so that we'll clean tx ring firstly,
thus maybe reclaim some skbs for rx.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If rix is not found in mi->r[], i will become -1 after the loop. This value
is eventually used to access arrays, so we were accessing arrays with a
negative index, which is obviously not what we want to do. This patch fixes
this potential problem.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code in cfg80211's cfg80211_bss_update erroneously
grabs a reference to the BSS, which means that it will
never be freed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.29, 2.6.30]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the third (I think) polarity error I accidentally
introduced in the rfkill rewrite to make wireless work
again on (certain?) HP laptops.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We're missing a Kconfig help for the iwmc3200wifi driver.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we reclaim the tx desc, we always assume that the
last desc is a holding desc, which is not true, and skip it.
If the tx queue is drained during channel change, internal
reset and etc, the last descriptor may not be the holding
descriptor and we fail to reclaim them. This results in the
following two issues.
1. Tx stuck - We drop all the frames coming from upper layer
due to shortage in tx desc.
2. Crash - If we fail to reclaim a tx descriptor, we miss to
update the tx BA window with the seq number of the frame
associated to that desc, which, at some point, result in
the following crash due to an assert failure in ath_tx_addto_baw().
This patch fixes these two issues.
kernel BUG at ../drivers/net/wireless/ath/ath9k/xmit.c:180!
[155064.304164] invalid opcode: 0000 [#1] SMP
Call Trace:
[<fbc6d83b>] ? ath9k_tx+0xeb/0x160 [ath9k]
[<fbbc9591>] ipv6? __ieee80211_tx+0x41/0x120 [mac80211]
[<fbbcb5ae>] ? aes_i586ieee80211_master_start_xmit+0x28e/0x560 [mac80211]
[<c037e501>] aes_generic? _spin_lock_irqsave+0x31/0x40
[<c02f347b>] ? dev_hard_start_xmit+0x16b/0x1c0
[<c03058b5>] ? __qdisc_run+0x1b5/0x200
[<fbbcda5a>] ? af_packetieee80211_select_queue+0xa/0x100 [mac80211]
[<c02f53b7>] ? i915dev_queue_xmit+0x2e7/0x3f0
[<fbbc9b49>] ? ieee80211_subif_start_xmit+0x369/0x7a0 [mac80211]
[<c031bc35>] ? ip_output+0x55/0xb0
[<c02e0188>] ? show_memcpy_count+0x18/0x60
[<c02eb186>] ? __kfree_skb+0x36/0x90
[<c02f2202>] ? binfmt_miscdev_queue_xmit_nit+0xd2/0x110
[<c02f347b>] ? dev_hard_start_xmit+0x16b/0x1c0
[<c03058b5>] ? __qdisc_run+0x1b5/0x200
[<c033bca7>] ? scoarp_create+0x57/0x2a0
[<c02f53b7>] ? bridgedev_queue_xmit+0x2e7/0x3f0
[<c03034a0>] ? eth_header+0x0/0xc0
[<c033b95f>] stp? arp_xmit+0x5f/0x70
[<c033bf4f>] ? arp_send+0x5f/0x70
[<c033c8f5>] bnep? arp_solicit+0x105/0x210
[<c02fa5aa>] ? neigh_timer_handler+0x19a/0x390
[<c013bf88>] ? run_timer_softirq+0x138/0x210
[<c02fa410>] ? ppdevneigh_timer_handler+0x0/0x390
[<c02fa410>] ? neigh_timer_handler+0x0/0x390
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix condition in which radio LED did not initialize correctly, and remove
4 compilation warnings.
After the recent changes in rfkill, the radio LED used by b43/b43legacy
did not always initialize correctly.
Both b43 and b43legacy used the deprecated variable radio_enabled in
struct ieee80211_conf.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't forget to unlock cfg80211_mutex in one fail path of
nl80211_set_wiphy.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The constant DMA_RX_MODE is defined to be 0x14 in the local include file
cs89x0.h. Since a constant with the same name is used elsewhere with
set_dma_mode, it seems likely that this constant could be used here.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@ expression E1; identifier I; constant int C; @@
(
set_dma_mode(E1,I,...)
|
*set_dma_mode(E1,C,...)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec: fix definition of 5272 version of FEC_X_DES_ACTIVE register
The ColdFire 5272 FEC driver has a different register address map
than other users of the FEC driver. And its definition of the
FEC_X_DES_ACTIVE register is incorrect, it should be 0x14.
The fec interface cannot transmit data with the old value.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
----
Signed-off-by: David S. Miller <davem@davemloft.net>
Add checksum offload support for DM9000A and DM9000B chips.
v2 changes: added a local copy of ip_summed to save IO cycles in dm9000_send_packet
v3 changes: trans_start updating is removed.
Signed-off-by: Yeasah Pell <yeasah@comrex.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The routine ipv6_rcv() uses magic number 0 for a return when it drops a
packet. This corresponds to NET_RX_SUCCESS, which is obviously
incorrect. Correct this by using NET_RX_DROP instead.
ps. It isn't exactly clear who the IPv6 maintainers are, apologies if
I've missed any.
Signed-off-by: Mark Smith <markzzzsmith@yahoo.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
when testing the jumbo frames with pages patch, the stats would
show rx_missed errors (dropped packets) even when connected to a
link partner with flow control enabled.
this indicates that for this MTU (9000) the flow control
thresholds are not adjusting correctly.
In fact, before this change, the FCRTH (xoff threshold) is 36864
when the fifo size is only 40000, with 9000 byte MTU.
fix it so that we at least have room for one frame after we send
the xoff.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is code extremely similar to what is committed in e1000e
already.
e1000 will no longer request 32kB slab buffers to support jumbo
frames on PCI/PCI-X adapters. This will significantly reduce the
likelyhood of order:3 allocation failures.
This new code adds support for using pages as receive buffers,
and the driver will chain multiple pages together to build a
jumbo frame for OS consumption.
The hardware takes a power of two buffer size and will
dump as much data as it can receive into 1 or more buffers.
The benefits of applying this are
1) stop akpm's dissing :-) of this lame e1000 behavior [1]
2) more efficient memory allocation (half) when using jumbo
frames, which will also allow for much better socket utilization
with jumbos since the socket is charged for the full allocation
of each receive buffer, regardless of how much is used.
3) this was a feature request by a customer
4) copybreak for small packets < 256 bytes still applies
[1] http://lkml.org/lkml/2008/7/10/68http://article.gmane.org/gmane.linux.network/130986
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows on-the-fly adjustment of the interrupts per second generated
by e1000 devices 82545/82546 (hardware support of ITR register is a
requirement)
adjust using this command:
ethtool -C eth0 rx-usecs 10
where 10 is 10 microseconds per interrupt interval, so 10 = 100,000 interrupts
per second, and 125 = 8000 interrupts per second.
changes should be immediate.
1,3 are special values and indicate the automatic tuning mode to the driver,
where 1 is 4000-90000 interrupts per second and 3 is 4000-20000 interrupts
per second and is the driver default.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Advance driver version number after modifications.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Use more efficient way to determine flag status.
2. Hardware dose not mark fragment bit against IPv6 packets,
print TCP/UDP checksum warning message for IPv4 packets
only.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware failed to update the shadow register in several cases.
It's known to be failed at 64bit box with more than 4G RAM.
In order to make the device working stable, give up using the shadow
register feature.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a large chunk of memory space preserved for
for modules, using kmalloc to obtain the needed memory.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Making coding style more consistent.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the remaining occurences of raw return values to their
symbolic counterparts in ndo_start_xmit() functions that were missed by the
previous automatic conversion.
Additionally code that assumed the symbolic value of NETDEV_TX_OK to be zero
is changed to explicitly use NETDEV_TX_OK.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Version update
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Printing the function's configured mode of operation.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Disable fcs stripping. The minimum frame size that can be received by the
hardware is 57 Bytes. A 64 Byte Ethernet frame with the vlan tag and fcs
stripped will result in a 56 Byte frame which will lock up the receive
engine. The work around is to disable fcs stripping in the hardware which
is done with a firmware upgrade. The fixes are -
1. Ensure that the correct firmware version is used.
2. Decrement the indicated packet length of the receive packet by 4 bytes
(FCS length).
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fixes in isr routine
Fixed crash with INTA mode during driver unload. Pass hldev to request_irq
instead of vdev.
Fixed Traffic failure with GRO in INTA mode. Pass the correct napi
context to gro functions.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Removed the code to bounds check the mss value. The hardware does bounds checking and
will not allow an oversized mss to lockup the transmit path.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
