Merge branch 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6

* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  hwmon: (abituguru3) Fix CONFIG_DMI=n fallback to probe
  hwmon: (abituguru3) Enable DMI probing feature on IN9 32X MAX
  hwmon: (abituguru3) Match partial DMI board name strings
  hwmon: Add a driver for the ADT7475 hardware monitoring chip
  hwmon: (k8temp) Fix temperature reporting for (most) K8 RevG CPUs
  hwmon: (k8temp) Fix wrong sensor selection for AMD K8 RevF/RevG CPUs
  hwmon: (k8temp) Warn about fam F rev F errata

Documentation/hwmon/adt7475

@@ -0,0 +1,87 @@
+This describes the interface for the ADT7475 driver:
+
+(there are 4 fans, numbered fan1 to fan4):
+
+fanX_input		Read the current speed of the fan (in RPMs)
+fanX_min		Read/write the minimum speed of the fan.  Dropping
+			below this sets an alarm.
+
+(there are three PWMs, numbered pwm1 to pwm3):
+
+pwmX			Read/write the current duty cycle of the PWM.  Writes
+			only have effect when auto mode is turned off (see
+			below).  Range is 0 - 255.
+
+pwmX_enable		Fan speed control method:
+
+			0 - No control (fan at full speed)
+			1 - Manual fan speed control (using pwm[1-*])
+			2 - Automatic fan speed control
+
+pwmX_auto_channels_temp	Select which channels affect this PWM
+
+			1 - TEMP1 controls PWM
+			2 - TEMP2 controls PWM
+			4 - TEMP3 controls PWM
+			6 - TEMP2 and TEMP3 control PWM
+			7 - All three inputs control PWM
+
+pwmX_freq		Read/write the PWM frequency in Hz. The number
+			should be one of the following:
+
+			11 Hz
+			14 Hz
+			22 Hz
+			29 Hz
+			35 Hz
+			44 Hz
+			58 Hz
+			88 Hz
+
+pwmX_auto_point1_pwm	Read/write the minimum PWM duty cycle in automatic mode
+
+pwmX_auto_point2_pwm	Read/write the maximum PWM duty cycle in automatic mode
+
+(there are three temperature settings numbered temp1 to temp3):
+
+tempX_input		Read the current temperature.  The value is in milli
+			degrees of Celsius.
+
+tempX_max		Read/write the upper temperature limit - exceeding this
+			will cause an alarm.
+
+tempX_min		Read/write the lower temperature limit - exceeding this
+			will cause an alarm.
+
+tempX_offset		Read/write the temperature adjustment offset
+
+tempX_crit		Read/write the THERM limit for remote1.
+
+tempX_crit_hyst		Set the temperature value below crit where the
+			fans will stay on - this helps drive the temperature
+			low enough so it doesn't stay near the edge and
+			cause THERM to keep tripping.
+
+tempX_auto_point1_temp	Read/write the minimum temperature where the fans will
+			turn on in automatic mode.
+
+tempX_auto_point2_temp	Read/write the maximum temperature over which the fans
+			will run in automatic mode.  tempX_auto_point1_temp
+			and tempX_auto_point2_temp together define the
+			range of automatic control.
+
+tempX_alarm		Read a 1 if the max/min alarm is set
+tempX_fault		Read a 1 if either temp1 or temp3 diode has a fault
+
+(There are two voltage settings, in1 and in2):
+
+inX_input		Read the current voltage on VCC.  Value is in
+			millivolts.
+
+inX_min			read/write the minimum voltage limit.
+			Dropping below this causes an alarm.
+
+inX_max			read/write the maximum voltage limit.
+			Exceeding this causes an alarm.
+
+inX_alarm		Read a 1 if the max/min alarm is set.

drivers/hwmon/Kconfig

@@ -189,6 +189,16 @@ config SENSORS_ADT7473
 	  This driver can also be built as a module. If so, the module
 	  will be called adt7473.
 
+config SENSORS_ADT7475
+	tristate "Analog Devices ADT7475"
+	depends on I2C && EXPERIMENTAL
+	help
+	  If you say yes here you get support for the Analog Devices
+	  ADT7475 hardware monitoring chips.
+
+	  This driver can also be build as a module.  If so, the module
+	  will be called adt7475.
+
 config SENSORS_K8TEMP
 	tristate "AMD Athlon64/FX or Opteron temperature sensor"
 	depends on X86 && PCI && EXPERIMENTAL

drivers/hwmon/Makefile

@@ -28,6 +28,8 @@ obj-$(CONFIG_SENSORS_ADS7828)	+= ads7828.o
 obj-$(CONFIG_SENSORS_ADT7462)	+= adt7462.o
 obj-$(CONFIG_SENSORS_ADT7470)	+= adt7470.o
 obj-$(CONFIG_SENSORS_ADT7473)	+= adt7473.o
+obj-$(CONFIG_SENSORS_ADT7475)	+= adt7475.o
+
 obj-$(CONFIG_SENSORS_APPLESMC)	+= applesmc.o
 obj-$(CONFIG_SENSORS_AMS)	+= ams/
 obj-$(CONFIG_SENSORS_ATXP1)	+= atxp1.o

drivers/hwmon/abituguru3.c

@@ -279,7 +279,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = {
 		{ "OTES1 Fan",		36, 2, 60, 1, 0 },
 		{ NULL, 0, 0, 0, 0, 0 } }
 	},
-	{ 0x0011, "AT8 32X(ATI RD580-ULI M1575)", {
+	{ 0x0011, "AT8 32X", {
 		{ "CPU Core",		 0, 0, 10, 1, 0 },
 		{ "DDR",		 1, 0, 20, 1, 0 },
 		{ "DDR VTT",		 2, 0, 10, 1, 0 },
@@ -402,7 +402,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = {
 		{ "AUX3 Fan",		36, 2, 60, 1, 0 },
 		{ NULL, 0, 0, 0, 0, 0 } }
 	},
-	{ 0x0016, "AW9D-MAX       (Intel i975-ICH7)", {
+	{ 0x0016, "AW9D-MAX", {
 		{ "CPU Core",		 0, 0, 10, 1, 0 },
 		{ "DDR2",		 1, 0, 20, 1, 0 },
 		{ "DDR2 VTT",		 2, 0, 10, 1, 0 },
@@ -482,7 +482,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = {
 		{ "AUX3 Fan",		36, 2, 60, 1, 0 },
 		{ NULL, 0, 0, 0, 0, 0 } }
 	},
-	{ 0x0019, NULL /* Unknown, need DMI string */, {
+	{ 0x0019, "IN9 32X MAX", {
 		{ "CPU Core",		 7, 0, 10, 1, 0 },
 		{ "DDR2",		13, 0, 20, 1, 0 },
 		{ "DDR2 VTT",		14, 0, 10, 1, 0 },
@@ -509,7 +509,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = {
 		{ "AUX3 FAN",		36, 2, 60, 1, 0 },
 		{ NULL, 0, 0, 0, 0, 0 } }
 	},
-	{ 0x001A, "IP35 Pro(Intel P35-ICH9R)", {
+	{ 0x001A, "IP35 Pro", {
 		{ "CPU Core",		 0, 0, 10, 1, 0 },
 		{ "DDR2",		 1, 0, 20, 1, 0 },
 		{ "DDR2 VTT",		 2, 0, 10, 1, 0 },
@@ -1128,6 +1128,7 @@ static int __init abituguru3_dmi_detect(void)
 {
 	const char *board_vendor, *board_name;
 	int i, err = (force) ? 1 : -ENODEV;
+	size_t sublen;
 
 	board_vendor = dmi_get_system_info(DMI_BOARD_VENDOR);
 	if (!board_vendor || strcmp(board_vendor, "http://www.abit.com.tw/"))
@@ -1137,9 +1138,20 @@ static int __init abituguru3_dmi_detect(void)
 	if (!board_name)
 		return err;
 
+	/* At the moment, we don't care about the part of the vendor
+	 * DMI string contained in brackets. Truncate the string at
+	 * the first occurrence of a bracket. Trim any trailing space
+	 * from the substring.
+	 */
+	sublen = strcspn(board_name, "(");
+	while (sublen > 0 && board_name[sublen - 1] == ' ')
+		sublen--;
+
 	for (i = 0; abituguru3_motherboards[i].id; i++) {
 		const char *dmi_name = abituguru3_motherboards[i].dmi_name;
-		if (dmi_name && !strcmp(dmi_name, board_name))
+		if (!dmi_name || strlen(dmi_name) != sublen)
+			continue;
+		if (!strncasecmp(board_name, dmi_name, sublen))
 			break;
 	}
 
@@ -1153,7 +1165,7 @@ static int __init abituguru3_dmi_detect(void)
 
 static inline int abituguru3_dmi_detect(void)
 {
-	return -ENODEV;
+	return 1;
 }
 
 #endif /* CONFIG_DMI */

drivers/hwmon/k8temp.c

@@ -31,6 +31,7 @@
 #include <linux/hwmon-sysfs.h>
 #include <linux/err.h>
 #include <linux/mutex.h>
+#include <asm/processor.h>
 
 #define TEMP_FROM_REG(val)	(((((val) >> 16) & 0xff) - 49) * 1000)
 #define REG_TEMP	0xe4
@@ -47,6 +48,8 @@ struct k8temp_data {
 	/* registers values */
 	u8 sensorsp;		/* sensor presence bits - SEL_CORE & SEL_PLACE */
 	u32 temp[2][2];		/* core, place */
+	u8 swap_core_select;    /* meaning of SEL_CORE is inverted */
+	u32 temp_offset;
 };
 
 static struct k8temp_data *k8temp_update_device(struct device *dev)
@@ -114,10 +117,15 @@ static ssize_t show_temp(struct device *dev,
 	    to_sensor_dev_attr_2(devattr);
 	int core = attr->nr;
 	int place = attr->index;
+	int temp;
 	struct k8temp_data *data = k8temp_update_device(dev);
 
-	return sprintf(buf, "%d\n",
-		       TEMP_FROM_REG(data->temp[core][place]));
+	if (data->swap_core_select)
+		core = core ? 0 : 1;
+
+	temp = TEMP_FROM_REG(data->temp[core][place]) + data->temp_offset;
+
+	return sprintf(buf, "%d\n", temp);
 }
 
 /* core, place */
@@ -141,20 +149,49 @@ static int __devinit k8temp_probe(struct pci_dev *pdev,
 	int err;
 	u8 scfg;
 	u32 temp;
+	u8 model, stepping;
 	struct k8temp_data *data;
-	u32 cpuid = cpuid_eax(1);
-
-	/* this feature should be available since SH-C0 core */
-	if ((cpuid == 0xf40) || (cpuid == 0xf50) || (cpuid == 0xf51)) {
-		err = -ENODEV;
-		goto exit;
-	}
 
 	if (!(data = kzalloc(sizeof(struct k8temp_data), GFP_KERNEL))) {
 		err = -ENOMEM;
 		goto exit;
 	}
 
+	model = boot_cpu_data.x86_model;
+	stepping = boot_cpu_data.x86_mask;
+
+	switch (boot_cpu_data.x86) {
+	case 0xf:
+		/* feature available since SH-C0, exclude older revisions */
+		if (((model == 4) && (stepping == 0)) ||
+		    ((model == 5) && (stepping <= 1))) {
+			err = -ENODEV;
+			goto exit_free;
+		}
+
+		/*
+		 * AMD NPT family 0fh, i.e. RevF and RevG:
+		 * meaning of SEL_CORE bit is inverted
+		 */
+		if (model >= 0x40) {
+			data->swap_core_select = 1;
+			dev_warn(&pdev->dev, "Temperature readouts might be "
+				 "wrong - check erratum #141\n");
+		}
+
+		if ((model >= 0x69) &&
+		    !(model == 0xc1 || model == 0x6c || model == 0x7c)) {
+			/*
+			 * RevG desktop CPUs (i.e. no socket S1G1 parts)
+			 * need additional offset, otherwise reported
+			 * temperature is below ambient temperature
+			 */
+			data->temp_offset = 21000;
+		}
+
+		break;
+	}
+
 	pci_read_config_byte(pdev, REG_TEMP, &scfg);
 	scfg &= ~(SEL_PLACE | SEL_CORE);		/* Select sensor 0, core0 */
 	pci_write_config_byte(pdev, REG_TEMP, scfg);