mirror of
https://github.com/adulau/aha.git
synced 2024-12-27 03:06:10 +00:00
hwmon: (lm93) Documentation fixes
* Drop documentation of generic module parameters. * Drop redundant section "Driver Description". * Drop sample configuration section, it belongs to sensors.conf.eg. * Random spelling and punctuation fixes. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Hans J. Koch <hjk@linutronix.de> Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This commit is contained in:
Jean Delvare
Mark M. Hoffman
parent
b26f933092
commit
471c606827
1 changed files with 8 additions and 118 deletions
|
|
@ -7,7 +7,7 @@ Supported chips:
|
|||
Addresses scanned: I2C 0x2c-0x2e
|
||||
Datasheet: http://www.national.com/ds.cgi/LM/LM93.pdf
|
||||
|
||||
Author:
|
||||
Authors:
|
||||
Mark M. Hoffman <mhoffman@lightlink.com>
|
||||
Ported to 2.6 by Eric J. Bowersox <ericb@aspsys.com>
|
||||
Adapted to 2.6.20 by Carsten Emde <ce@osadl.org>
|
||||
|
|
@ -16,7 +16,6 @@ Author:
|
|||
Module Parameters
|
||||
-----------------
|
||||
|
||||
(specific to LM93)
|
||||
* init: integer
|
||||
Set to non-zero to force some initializations (default is 0).
|
||||
* disable_block: integer
|
||||
|
|
@ -37,30 +36,13 @@ Module Parameters
|
|||
I.e. this parameter controls the VID pin input thresholds; if your VID
|
||||
inputs are not working, try changing this. The default value is "0".
|
||||
|
||||
(common among sensor drivers)
|
||||
* force: short array (min = 1, max = 48)
|
||||
List of adapter,address pairs to assume to be present. Autodetection
|
||||
of the target device will still be attempted. Use one of the more
|
||||
specific force directives below if this doesn't detect the device.
|
||||
* force_lm93: short array (min = 1, max = 48)
|
||||
List of adapter,address pairs which are unquestionably assumed to contain
|
||||
a 'lm93' chip
|
||||
* ignore: short array (min = 1, max = 48)
|
||||
List of adapter,address pairs not to scan
|
||||
* ignore_range: short array (min = 1, max = 48)
|
||||
List of adapter,start-addr,end-addr triples not to scan
|
||||
* probe: short array (min = 1, max = 48)
|
||||
List of adapter,address pairs to scan additionally
|
||||
* probe_range: short array (min = 1, max = 48)
|
||||
List of adapter,start-addr,end-addr triples to scan additionally
|
||||
|
||||
|
||||
Hardware Description
|
||||
--------------------
|
||||
|
||||
(from the datasheet)
|
||||
|
||||
The LM93, hardware monitor, has a two wire digital interface compatible with
|
||||
The LM93 hardware monitor has a two wire digital interface compatible with
|
||||
SMBus 2.0. Using an 8-bit ADC, the LM93 measures the temperature of two remote
|
||||
diode connected transistors as well as its own die and 16 power supply
|
||||
voltages. To set fan speed, the LM93 has two PWM outputs that are each
|
||||
|
|
@ -69,18 +51,12 @@ table based. The LM93 includes a digital filter that can be invoked to smooth
|
|||
temperature readings for better control of fan speed. The LM93 has four
|
||||
tachometer inputs to measure fan speed. Limit and status registers for all
|
||||
measured values are included. The LM93 builds upon the functionality of
|
||||
previous motherboard management ASICs and uses some of the LM85 s features
|
||||
previous motherboard management ASICs and uses some of the LM85's features
|
||||
(i.e. smart tachometer mode). It also adds measurement and control support
|
||||
for dynamic Vccp monitoring and PROCHOT. It is designed to monitor a dual
|
||||
processor Xeon class motherboard with a minimum of external components.
|
||||
|
||||
|
||||
Driver Description
|
||||
------------------
|
||||
|
||||
This driver implements support for the National Semiconductor LM93.
|
||||
|
||||
|
||||
User Interface
|
||||
--------------
|
||||
|
||||
|
|
@ -101,7 +77,7 @@ These intervals can be found in the sysfs files prochot1_interval and
|
|||
prochot2_interval. The values in these files specify the intervals for
|
||||
#P1_PROCHOT and #P2_PROCHOT, respectively. Selecting a value not in this
|
||||
list will cause the driver to use the next largest interval. The available
|
||||
intervals are:
|
||||
intervals are (in seconds):
|
||||
|
||||
#PROCHOT intervals: 0.73, 1.46, 2.9, 5.8, 11.7, 23.3, 46.6, 93.2, 186, 372
|
||||
|
||||
|
|
@ -111,12 +87,12 @@ assert #P2_PROCHOT, and vice-versa. This mode is enabled by writing a
|
|||
non-zero integer to the sysfs file prochot_short.
|
||||
|
||||
The LM93 can also override the #PROCHOT pins by driving a PWM signal onto
|
||||
one or both of them. When overridden, the signal has a period of 3.56 mS,
|
||||
one or both of them. When overridden, the signal has a period of 3.56 ms,
|
||||
a minimum pulse width of 5 clocks (at 22.5kHz => 6.25% duty cycle), and
|
||||
a maximum pulse width of 80 clocks (at 22.5kHz => 99.88% duty cycle).
|
||||
|
||||
The sysfs files prochot1_override and prochot2_override contain boolean
|
||||
intgers which enable or disable the override function for #P1_PROCHOT and
|
||||
integers which enable or disable the override function for #P1_PROCHOT and
|
||||
#P2_PROCHOT, respectively. The sysfs file prochot_override_duty_cycle
|
||||
contains a value controlling the duty cycle for the PWM signal used when
|
||||
the override function is enabled. This value ranges from 0 to 15, with 0
|
||||
|
|
@ -166,7 +142,7 @@ frequency values are constrained by the hardware. Selecting a value which is
|
|||
not available will cause the driver to use the next largest value. Also note
|
||||
that this parameter has implications for the Smart Tach Mode (see above).
|
||||
|
||||
PWM Output Frequencies: 12, 36, 48, 60, 72, 84, 96, 22500 (h/w default)
|
||||
PWM Output Frequencies (in Hz): 12, 36, 48, 60, 72, 84, 96, 22500 (default)
|
||||
|
||||
Automatic PWM:
|
||||
|
||||
|
|
@ -178,7 +154,7 @@ individual control sources to which the PWM output is bound.
|
|||
The eight control sources are: temp1-temp4 (aka "zones" in the datasheet),
|
||||
#PROCHOT 1 & 2, and #VRDHOT 1 & 2. The bindings are expressed as a bitmask
|
||||
in the sysfs files pwm<n>_auto_channels, where a "1" enables the binding, and
|
||||
a "0" disables it. The h/w default is 0x0f (all temperatures bound).
|
||||
a "0" disables it. The h/w default is 0x0f (all temperatures bound).
|
||||
|
||||
0x01 - Temp 1
|
||||
0x02 - Temp 2
|
||||
|
|
@ -324,89 +300,3 @@ LM93 Unique sysfs Files
|
|||
|
||||
gpio input state of 8 GPIO pins; read-only
|
||||
|
||||
|
||||
Sample Configuration File
|
||||
-------------------------
|
||||
|
||||
Here is a sample LM93 chip config for sensors.conf:
|
||||
|
||||
---------- cut here ----------
|
||||
chip "lm93-*"
|
||||
|
||||
# VOLTAGE INPUTS
|
||||
|
||||
# labels and scaling based on datasheet recommendations
|
||||
label in1 "+12V1"
|
||||
compute in1 @ * 12.945, @ / 12.945
|
||||
set in1_min 12 * 0.90
|
||||
set in1_max 12 * 1.10
|
||||
|
||||
label in2 "+12V2"
|
||||
compute in2 @ * 12.945, @ / 12.945
|
||||
set in2_min 12 * 0.90
|
||||
set in2_max 12 * 1.10
|
||||
|
||||
label in3 "+12V3"
|
||||
compute in3 @ * 12.945, @ / 12.945
|
||||
set in3_min 12 * 0.90
|
||||
set in3_max 12 * 1.10
|
||||
|
||||
label in4 "FSB_Vtt"
|
||||
|
||||
label in5 "3GIO"
|
||||
|
||||
label in6 "ICH_Core"
|
||||
|
||||
label in7 "Vccp1"
|
||||
|
||||
label in8 "Vccp2"
|
||||
|
||||
label in9 "+3.3V"
|
||||
set in9_min 3.3 * 0.90
|
||||
set in9_max 3.3 * 1.10
|
||||
|
||||
label in10 "+5V"
|
||||
set in10_min 5.0 * 0.90
|
||||
set in10_max 5.0 * 1.10
|
||||
|
||||
label in11 "SCSI_Core"
|
||||
|
||||
label in12 "Mem_Core"
|
||||
|
||||
label in13 "Mem_Vtt"
|
||||
|
||||
label in14 "Gbit_Core"
|
||||
|
||||
# Assuming R1/R2 = 4.1143, and 3.3V reference
|
||||
# -12V = (4.1143 + 1) * (@ - 3.3) + 3.3
|
||||
label in15 "-12V"
|
||||
compute in15 @ * 5.1143 - 13.57719, (@ + 13.57719) / 5.1143
|
||||
set in15_min -12 * 0.90
|
||||
set in15_max -12 * 1.10
|
||||
|
||||
label in16 "+3.3VSB"
|
||||
set in16_min 3.3 * 0.90
|
||||
set in16_max 3.3 * 1.10
|
||||
|
||||
# TEMPERATURE INPUTS
|
||||
|
||||
label temp1 "CPU1"
|
||||
label temp2 "CPU2"
|
||||
label temp3 "LM93"
|
||||
|
||||
# TACHOMETER INPUTS
|
||||
|
||||
label fan1 "Fan1"
|
||||
set fan1_min 3000
|
||||
label fan2 "Fan2"
|
||||
set fan2_min 3000
|
||||
label fan3 "Fan3"
|
||||
set fan3_min 3000
|
||||
label fan4 "Fan4"
|
||||
set fan4_min 3000
|
||||
|
||||
# PWM OUTPUTS
|
||||
|
||||
label pwm1 "CPU1"
|
||||
label pwm2 "CPU2"
|
||||
|
||||
|
|
|
|||
Loading…
Reference in a new issue