diff --git a/Documentation/i2c/busses/i2c-piix4 b/Documentation/i2c/busses/i2c-piix4 index f889481762b..c5b37c57055 100644 --- a/Documentation/i2c/busses/i2c-piix4 +++ b/Documentation/i2c/busses/i2c-piix4 @@ -8,6 +8,8 @@ Supported adapters: Datasheet: Only available via NDA from ServerWorks * ATI IXP200, IXP300, IXP400, SB600, SB700 and SB800 southbridges Datasheet: Not publicly available + * AMD SB900 + Datasheet: Not publicly available * Standard Microsystems (SMSC) SLC90E66 (Victory66) southbridge Datasheet: Publicly available at the SMSC website http://www.smsc.com diff --git a/Documentation/i2c/chips/pca9539 b/Documentation/i2c/chips/pca9539 deleted file mode 100644 index 6aff890088b..00000000000 --- a/Documentation/i2c/chips/pca9539 +++ /dev/null @@ -1,58 +0,0 @@ -Kernel driver pca9539 -===================== - -NOTE: this driver is deprecated and will be dropped soon, use -drivers/gpio/pca9539.c instead. - -Supported chips: - * Philips PCA9539 - Prefix: 'pca9539' - Addresses scanned: none - Datasheet: - http://www.semiconductors.philips.com/acrobat/datasheets/PCA9539_2.pdf - -Author: Ben Gardner - - -Description ------------ - -The Philips PCA9539 is a 16 bit low power I/O device. -All 16 lines can be individually configured as an input or output. -The input sense can also be inverted. -The 16 lines are split between two bytes. - - -Detection ---------- - -The PCA9539 is difficult to detect and not commonly found in PC machines, -so you have to pass the I2C bus and address of the installed PCA9539 -devices explicitly to the driver at load time via the force=... parameter. - - -Sysfs entries -------------- - -Each is a byte that maps to the 8 I/O bits. -A '0' suffix is for bits 0-7, while '1' is for bits 8-15. - -input[01] - read the current value -output[01] - sets the output value -direction[01] - direction of each bit: 1=input, 0=output -invert[01] - toggle the input bit sense - -input reads the actual state of the line and is always available. -The direction defaults to input for all channels. - - -General Remarks ---------------- - -Note that each output, direction, and invert entry controls 8 lines. -You should use the read, modify, write sequence. -For example. to set output bit 0 of 1. - val=$(cat output0) - val=$(( $val | 1 )) - echo $val > output0 - diff --git a/Documentation/i2c/chips/pcf8574 b/Documentation/i2c/chips/pcf8574 deleted file mode 100644 index 235815c075f..00000000000 --- a/Documentation/i2c/chips/pcf8574 +++ /dev/null @@ -1,65 +0,0 @@ -Kernel driver pcf8574 -===================== - -Supported chips: - * Philips PCF8574 - Prefix: 'pcf8574' - Addresses scanned: none - Datasheet: Publicly available at the Philips Semiconductors website - http://www.semiconductors.philips.com/pip/PCF8574P.html - - * Philips PCF8574A - Prefix: 'pcf8574a' - Addresses scanned: none - Datasheet: Publicly available at the Philips Semiconductors website - http://www.semiconductors.philips.com/pip/PCF8574P.html - -Authors: - Frodo Looijaard , - Philip Edelbrock , - Dan Eaton , - Aurelien Jarno , - Jean Delvare , - - -Description ------------ -The PCF8574(A) is an 8-bit I/O expander for the I2C bus produced by Philips -Semiconductors. It is designed to provide a byte I2C interface to up to 16 -separate devices (8 x PCF8574 and 8 x PCF8574A). - -This device consists of a quasi-bidirectional port. Each of the eight I/Os -can be independently used as an input or output. To setup an I/O as an -input, you have to write a 1 to the corresponding output. - -For more informations see the datasheet. - - -Accessing PCF8574(A) via /sys interface -------------------------------------- - -The PCF8574(A) is plainly impossible to detect ! Stupid chip. -So, you have to pass the I2C bus and address of the installed PCF857A -and PCF8574A devices explicitly to the driver at load time via the -force=... parameter. - -On detection (i.e. insmod, modprobe et al.), directories are being -created for each detected PCF8574(A): - -/sys/bus/i2c/devices/<0>-<1>/ -where <0> is the bus the chip was detected on (e. g. i2c-0) -and <1> the chip address ([20..27] or [38..3f]): - -(example: /sys/bus/i2c/devices/1-0020/) - -Inside these directories, there are two files each: -read and write (and one file with chip name). - -The read file is read-only. Reading gives you the current I/O input -if the corresponding output is set as 1, otherwise the current output -value, that is to say 0. - -The write file is read/write. Writing a value outputs it on the I/O -port. Reading returns the last written value. As it is not possible -to read this value from the chip, you need to write at least once to -this file before you can read back from it. diff --git a/Documentation/i2c/chips/pcf8575 b/Documentation/i2c/chips/pcf8575 deleted file mode 100644 index 40b268eb276..00000000000 --- a/Documentation/i2c/chips/pcf8575 +++ /dev/null @@ -1,69 +0,0 @@ -About the PCF8575 chip and the pcf8575 kernel driver -==================================================== - -The PCF8575 chip is produced by the following manufacturers: - - * Philips NXP - http://www.nxp.com/#/pip/cb=[type=product,path=50807/41735/41850,final=PCF8575_3]|pip=[pip=PCF8575_3][0] - - * Texas Instruments - http://focus.ti.com/docs/prod/folders/print/pcf8575.html - - -Some vendors sell small PCB's with the PCF8575 mounted on it. You can connect -such a board to a Linux host via e.g. an USB to I2C interface. Examples of -PCB boards with a PCF8575: - - * SFE Breakout Board for PCF8575 I2C Expander by RobotShop - http://www.robotshop.ca/home/products/robot-parts/electronics/adapters-converters/sfe-pcf8575-i2c-expander-board.html - - * Breakout Board for PCF8575 I2C Expander by Spark Fun Electronics - http://www.sparkfun.com/commerce/product_info.php?products_id=8130 - - -Description ------------ -The PCF8575 chip is a 16-bit I/O expander for the I2C bus. Up to eight of -these chips can be connected to the same I2C bus. You can find this -chip on some custom designed hardware, but you won't find it on PC -motherboards. - -The PCF8575 chip consists of a 16-bit quasi-bidirectional port and an I2C-bus -interface. Each of the sixteen I/O's can be independently used as an input or -an output. To set up an I/O pin as an input, you have to write a 1 to the -corresponding output. - -For more information please see the datasheet. - - -Detection ---------- - -There is no method known to detect whether a chip on a given I2C address is -a PCF8575 or whether it is any other I2C device, so you have to pass the I2C -bus and address of the installed PCF8575 devices explicitly to the driver at -load time via the force=... parameter. - -/sys interface --------------- - -For each address on which a PCF8575 chip was found or forced the following -files will be created under /sys: -* /sys/bus/i2c/devices/-
/read -* /sys/bus/i2c/devices/-
/write -where bus is the I2C bus number (0, 1, ...) and address is the four-digit -hexadecimal representation of the 7-bit I2C address of the PCF8575 -(0020 .. 0027). - -The read file is read-only. Reading it will trigger an I2C read and will hence -report the current input state for the pins configured as inputs, and the -current output value for the pins configured as outputs. - -The write file is read-write. Writing a value to it will configure all pins -as output for which the corresponding bit is zero. Reading the write file will -return the value last written, or -EAGAIN if no value has yet been written to -the write file. - -On module initialization the configuration of the chip is not changed -- the -chip is left in the state it was already configured in through either power-up -or through previous I2C write actions. diff --git a/MAINTAINERS b/MAINTAINERS index e1fc32e394a..b9a8a365418 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -895,6 +895,13 @@ F: drivers/dma/ F: include/linux/dmaengine.h F: include/linux/async_tx.h +AT24 EEPROM DRIVER +M: Wolfram Sang +L: linux-i2c@vger.kernel.org +S: Maintained +F: drivers/misc/eeprom/at24.c +F: include/linux/i2c/at24.h + ATA OVER ETHERNET (AOE) DRIVER M: "Ed L. Cashin" W: http://www.coraid.com/support/linux @@ -3964,6 +3971,15 @@ S: Maintained F: drivers/leds/leds-pca9532.c F: include/linux/leds-pca9532.h +PCA9564/PCA9665 I2C BUS DRIVER +M: Wolfram Sang +L: linux-i2c@vger.kernel.org +S: Maintained +F: drivers/i2c/algos/i2c-algo-pca.c +F: drivers/i2c/busses/i2c-pca-* +F: include/linux/i2c-algo-pca.h +F: include/linux/i2c-pca-platform.h + PCI ERROR RECOVERY M: Linas Vepstas L: linux-pci@vger.kernel.org diff --git a/drivers/gpio/pcf857x.c b/drivers/gpio/pcf857x.c index 72f2449c1c8..29f19ce3e80 100644 --- a/drivers/gpio/pcf857x.c +++ b/drivers/gpio/pcf857x.c @@ -27,6 +27,7 @@ static const struct i2c_device_id pcf857x_id[] = { { "pcf8574", 8 }, + { "pcf8574a", 8 }, { "pca8574", 8 }, { "pca9670", 8 }, { "pca9672", 8 }, diff --git a/drivers/i2c/Kconfig b/drivers/i2c/Kconfig index 711ca08ab77..d7ece131b4f 100644 --- a/drivers/i2c/Kconfig +++ b/drivers/i2c/Kconfig @@ -27,6 +27,14 @@ config I2C_BOARDINFO boolean default y +config I2C_COMPAT + boolean "Enable compatibility bits for old user-space" + default y + help + Say Y here if you intend to run lm-sensors 3.1.1 or older, or any + other user-space package which expects i2c adapters to be class + devices. If you don't know, say Y. + config I2C_CHARDEV tristate "I2C device interface" help diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig index 8206442fbab..6bedd2fcfc1 100644 --- a/drivers/i2c/busses/Kconfig +++ b/drivers/i2c/busses/Kconfig @@ -113,7 +113,7 @@ config I2C_ISCH will be called i2c-isch. config I2C_PIIX4 - tristate "Intel PIIX4 and compatible (ATI/Serverworks/Broadcom/SMSC)" + tristate "Intel PIIX4 and compatible (ATI/AMD/Serverworks/Broadcom/SMSC)" depends on PCI help If you say yes to this option, support will be included for the Intel @@ -128,6 +128,7 @@ config I2C_PIIX4 ATI SB600 ATI SB700 ATI SB800 + AMD SB900 Serverworks OSB4 Serverworks CSB5 Serverworks CSB6 @@ -231,6 +232,22 @@ config I2C_VIAPRO This driver can also be built as a module. If so, the module will be called i2c-viapro. +if ACPI + +comment "ACPI drivers" + +config I2C_SCMI + tristate "SMBus Control Method Interface" + help + This driver supports the SMBus Control Method Interface. It needs the + BIOS to declare ACPI control methods as described in the SMBus Control + Method Interface specification. + + To compile this driver as a module, choose M here: + the module will be called i2c-scmi. + +endif # ACPI + comment "Mac SMBus host controller drivers" depends on PPC_CHRP || PPC_PMAC diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile index e654263bfc0..ff937ac69f5 100644 --- a/drivers/i2c/busses/Makefile +++ b/drivers/i2c/busses/Makefile @@ -2,6 +2,9 @@ # Makefile for the i2c bus drivers. # +# ACPI drivers +obj-$(CONFIG_I2C_SCMI) += i2c-scmi.o + # PC SMBus host controller drivers obj-$(CONFIG_I2C_ALI1535) += i2c-ali1535.o obj-$(CONFIG_I2C_ALI1563) += i2c-ali1563.o diff --git a/drivers/i2c/busses/i2c-piix4.c b/drivers/i2c/busses/i2c-piix4.c index 0249a7d762b..a782c7a08f9 100644 --- a/drivers/i2c/busses/i2c-piix4.c +++ b/drivers/i2c/busses/i2c-piix4.c @@ -22,6 +22,7 @@ Intel PIIX4, 440MX Serverworks OSB4, CSB5, CSB6, HT-1000, HT-1100 ATI IXP200, IXP300, IXP400, SB600, SB700, SB800 + AMD SB900 SMSC Victory66 Note: we assume there can only be one device, with one SMBus interface. @@ -479,6 +480,7 @@ static struct pci_device_id piix4_ids[] = { { PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP300_SMBUS) }, { PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP400_SMBUS) }, { PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_SBX00_SMBUS) }, + { PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_SB900_SMBUS) }, { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4) }, { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, @@ -499,9 +501,10 @@ static int __devinit piix4_probe(struct pci_dev *dev, { int retval; - if ((dev->vendor == PCI_VENDOR_ID_ATI) && - (dev->device == PCI_DEVICE_ID_ATI_SBX00_SMBUS) && - (dev->revision >= 0x40)) + if ((dev->vendor == PCI_VENDOR_ID_ATI && + dev->device == PCI_DEVICE_ID_ATI_SBX00_SMBUS && + dev->revision >= 0x40) || + dev->vendor == PCI_VENDOR_ID_AMD) /* base address location etc changed in SB800 */ retval = piix4_setup_sb800(dev, id); else diff --git a/drivers/i2c/busses/i2c-pnx.c b/drivers/i2c/busses/i2c-pnx.c index ec15cff556b..6ff6c20f1e7 100644 --- a/drivers/i2c/busses/i2c-pnx.c +++ b/drivers/i2c/busses/i2c-pnx.c @@ -586,7 +586,8 @@ static int __devinit i2c_pnx_probe(struct platform_device *pdev) alg_data->mif.timer.data = (unsigned long)i2c_pnx->adapter; /* Register I/O resource */ - if (!request_region(alg_data->base, I2C_PNX_REGION_SIZE, pdev->name)) { + if (!request_mem_region(alg_data->base, I2C_PNX_REGION_SIZE, + pdev->name)) { dev_err(&pdev->dev, "I/O region 0x%08x for I2C already in use.\n", alg_data->base); @@ -650,7 +651,7 @@ out_clock: out_unmap: iounmap((void *)alg_data->ioaddr); out_release: - release_region(alg_data->base, I2C_PNX_REGION_SIZE); + release_mem_region(alg_data->base, I2C_PNX_REGION_SIZE); out_drvdata: platform_set_drvdata(pdev, NULL); out: @@ -667,7 +668,7 @@ static int __devexit i2c_pnx_remove(struct platform_device *pdev) i2c_del_adapter(adap); i2c_pnx->set_clock_stop(pdev); iounmap((void *)alg_data->ioaddr); - release_region(alg_data->base, I2C_PNX_REGION_SIZE); + release_mem_region(alg_data->base, I2C_PNX_REGION_SIZE); platform_set_drvdata(pdev, NULL); return 0; diff --git a/drivers/i2c/busses/i2c-scmi.c b/drivers/i2c/busses/i2c-scmi.c new file mode 100644 index 00000000000..276a046ac93 --- /dev/null +++ b/drivers/i2c/busses/i2c-scmi.c @@ -0,0 +1,430 @@ +/* + * SMBus driver for ACPI SMBus CMI + * + * Copyright (C) 2009 Crane Cai + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation version 2. + */ + +#include +#include +#include +#include +#include +#include +#include + +#define ACPI_SMBUS_HC_CLASS "smbus" +#define ACPI_SMBUS_HC_DEVICE_NAME "cmi" + +ACPI_MODULE_NAME("smbus_cmi"); + +struct smbus_methods_t { + char *mt_info; + char *mt_sbr; + char *mt_sbw; +}; + +struct acpi_smbus_cmi { + acpi_handle handle; + struct i2c_adapter adapter; + u8 cap_info:1; + u8 cap_read:1; + u8 cap_write:1; +}; + +static const struct smbus_methods_t smbus_methods = { + .mt_info = "_SBI", + .mt_sbr = "_SBR", + .mt_sbw = "_SBW", +}; + +static const struct acpi_device_id acpi_smbus_cmi_ids[] = { + {"SMBUS01", 0}, + {"", 0} +}; + +#define ACPI_SMBUS_STATUS_OK 0x00 +#define ACPI_SMBUS_STATUS_FAIL 0x07 +#define ACPI_SMBUS_STATUS_DNAK 0x10 +#define ACPI_SMBUS_STATUS_DERR 0x11 +#define ACPI_SMBUS_STATUS_CMD_DENY 0x12 +#define ACPI_SMBUS_STATUS_UNKNOWN 0x13 +#define ACPI_SMBUS_STATUS_ACC_DENY 0x17 +#define ACPI_SMBUS_STATUS_TIMEOUT 0x18 +#define ACPI_SMBUS_STATUS_NOTSUP 0x19 +#define ACPI_SMBUS_STATUS_BUSY 0x1a +#define ACPI_SMBUS_STATUS_PEC 0x1f + +#define ACPI_SMBUS_PRTCL_WRITE 0x00 +#define ACPI_SMBUS_PRTCL_READ 0x01 +#define ACPI_SMBUS_PRTCL_QUICK 0x02 +#define ACPI_SMBUS_PRTCL_BYTE 0x04 +#define ACPI_SMBUS_PRTCL_BYTE_DATA 0x06 +#define ACPI_SMBUS_PRTCL_WORD_DATA 0x08 +#define ACPI_SMBUS_PRTCL_BLOCK_DATA 0x0a + + +static int +acpi_smbus_cmi_access(struct i2c_adapter *adap, u16 addr, unsigned short flags, + char read_write, u8 command, int size, + union i2c_smbus_data *data) +{ + int result = 0; + struct acpi_smbus_cmi *smbus_cmi = adap->algo_data; + unsigned char protocol; + acpi_status status = 0; + struct acpi_object_list input; + union acpi_object mt_params[5]; + struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL }; + union acpi_object *obj; + union acpi_object *pkg; + char *method; + int len = 0; + + dev_dbg(&adap->dev, "access size: %d %s\n", size, + (read_write) ? "READ" : "WRITE"); + switch (size) { + case I2C_SMBUS_QUICK: + protocol = ACPI_SMBUS_PRTCL_QUICK; + command = 0; + if (read_write == I2C_SMBUS_WRITE) { + mt_params[3].type = ACPI_TYPE_INTEGER; + mt_params[3].integer.value = 0; + mt_params[4].type = ACPI_TYPE_INTEGER; + mt_params[4].integer.value = 0; + } + break; + + case I2C_SMBUS_BYTE: + protocol = ACPI_SMBUS_PRTCL_BYTE; + if (read_write == I2C_SMBUS_WRITE) { + mt_params[3].type = ACPI_TYPE_INTEGER; + mt_params[3].integer.value = 0; + mt_params[4].type = ACPI_TYPE_INTEGER; + mt_params[4].integer.value = 0; + } else { + command = 0; + } + break; + + case I2C_SMBUS_BYTE_DATA: + protocol = ACPI_SMBUS_PRTCL_BYTE_DATA; + if (read_write == I2C_SMBUS_WRITE) { + mt_params[3].type = ACPI_TYPE_INTEGER; + mt_params[3].integer.value = 1; + mt_params[4].type = ACPI_TYPE_INTEGER; + mt_params[4].integer.value = data->byte; + } + break; + + case I2C_SMBUS_WORD_DATA: + protocol = ACPI_SMBUS_PRTCL_WORD_DATA; + if (read_write == I2C_SMBUS_WRITE) { + mt_params[3].type = ACPI_TYPE_INTEGER; + mt_params[3].integer.value = 2; + mt_params[4].type = ACPI_TYPE_INTEGER; + mt_params[4].integer.value = data->word; + } + break; + + case I2C_SMBUS_BLOCK_DATA: + protocol = ACPI_SMBUS_PRTCL_BLOCK_DATA; + if (read_write == I2C_SMBUS_WRITE) { + len = data->block[0]; + if (len == 0 || len > I2C_SMBUS_BLOCK_MAX) + return -EINVAL; + mt_params[3].type = ACPI_TYPE_INTEGER; + mt_params[3].integer.value = len; + mt_params[4].type = ACPI_TYPE_BUFFER; + mt_params[4].buffer.pointer = data->block + 1; + } + break; + + default: + dev_warn(&adap->dev, "Unsupported transaction %d\n", size); + return -EOPNOTSUPP; + } + + if (read_write == I2C_SMBUS_READ) { + protocol |= ACPI_SMBUS_PRTCL_READ; + method = smbus_methods.mt_sbr; + input.count = 3; + } else { + protocol |= ACPI_SMBUS_PRTCL_WRITE; + method = smbus_methods.mt_sbw; + input.count = 5; + } + + input.pointer = mt_params; + mt_params[0].type = ACPI_TYPE_INTEGER; + mt_params[0].integer.value = protocol; + mt_params[1].type = ACPI_TYPE_INTEGER; + mt_params[1].integer.value = addr; + mt_params[2].type = ACPI_TYPE_INTEGER; + mt_params[2].integer.value = command; + + status = acpi_evaluate_object(smbus_cmi->handle, method, &input, + &buffer); + if (ACPI_FAILURE(status)) { + ACPI_ERROR((AE_INFO, "Evaluating %s: %i", method, status)); + return -EIO; + } + + pkg = buffer.pointer; + if (pkg && pkg->type == ACPI_TYPE_PACKAGE) + obj = pkg->package.elements; + else { + ACPI_ERROR((AE_INFO, "Invalid argument type")); + result = -EIO; + goto out; + } + if (obj == NULL || obj->type != ACPI_TYPE_INTEGER) { + ACPI_ERROR((AE_INFO, "Invalid argument type")); + result = -EIO; + goto out; + } + + result = obj->integer.value; + ACPI_DEBUG_PRINT((ACPI_DB_INFO, "%s return status: %i\n", + method, result)); + + switch (result) { + case ACPI_SMBUS_STATUS_OK: + result = 0; + break; + case ACPI_SMBUS_STATUS_BUSY: + result = -EBUSY; + goto out; + case ACPI_SMBUS_STATUS_TIMEOUT: + result = -ETIMEDOUT; + goto out; + case ACPI_SMBUS_STATUS_DNAK: + result = -ENXIO; + goto out; + default: + result = -EIO; + goto out; + } + + if (read_write == I2C_SMBUS_WRITE || size == I2C_SMBUS_QUICK) + goto out; + + obj = pkg->package.elements + 1; + if (obj == NULL || obj->type != ACPI_TYPE_INTEGER) { + ACPI_ERROR((AE_INFO, "Invalid argument type")); + result = -EIO; + goto out; + } + + len = obj->integer.value; + obj = pkg->package.elements + 2; + switch (size) { + case I2C_SMBUS_BYTE: + case I2C_SMBUS_BYTE_DATA: + case I2C_SMBUS_WORD_DATA: + if (obj == NULL || obj->type != ACPI_TYPE_INTEGER) { + ACPI_ERROR((AE_INFO, "Invalid argument type")); + result = -EIO; + goto out; + } + if (len == 2) + data->word = obj->integer.value; + else + data->byte = obj->integer.value; + break; + case I2C_SMBUS_BLOCK_DATA: + if (obj == NULL || obj->type != ACPI_TYPE_BUFFER) { + ACPI_ERROR((AE_INFO, "Invalid argument type")); + result = -EIO; + goto out; + } + if (len == 0 || len > I2C_SMBUS_BLOCK_MAX) + return -EPROTO; + data->block[0] = len; + memcpy(data->block + 1, obj->buffer.pointer, len); + break; + } + +out: + kfree(buffer.pointer); + dev_dbg(&adap->dev, "Transaction status: %i\n", result); + return result; +} + +static u32 acpi_smbus_cmi_func(struct i2c_adapter *adapter) +{ + struct acpi_smbus_cmi *smbus_cmi = adapter->algo_data; + u32 ret; + + ret = smbus_cmi->cap_read | smbus_cmi->cap_write ? + I2C_FUNC_SMBUS_QUICK : 0; + + ret |= smbus_cmi->cap_read ? + (I2C_FUNC_SMBUS_READ_BYTE | + I2C_FUNC_SMBUS_READ_BYTE_DATA | + I2C_FUNC_SMBUS_READ_WORD_DATA | + I2C_FUNC_SMBUS_READ_BLOCK_DATA) : 0; + + ret |= smbus_cmi->cap_write ? + (I2C_FUNC_SMBUS_WRITE_BYTE | + I2C_FUNC_SMBUS_WRITE_BYTE_DATA | + I2C_FUNC_SMBUS_WRITE_WORD_DATA | + I2C_FUNC_SMBUS_WRITE_BLOCK_DATA) : 0; + + return ret; +} + +static const struct i2c_algorithm acpi_smbus_cmi_algorithm = { + .smbus_xfer = acpi_smbus_cmi_access, + .functionality = acpi_smbus_cmi_func, +}; + + +static int acpi_smbus_cmi_add_cap(struct acpi_smbus_cmi *smbus_cmi, + const char *name) +{ + struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL }; + union acpi_object *obj; + acpi_status status; + + if (!strcmp(name, smbus_methods.mt_info)) { + status = acpi_evaluate_object(smbus_cmi->handle, + smbus_methods.mt_info, + NULL, &buffer); + if (ACPI_FAILURE(status)) { + ACPI_ERROR((AE_INFO, "Evaluating %s: %i", + smbus_methods.mt_info, status)); + return -EIO; + } + + obj = buffer.pointer; + if (obj && obj->type == ACPI_TYPE_PACKAGE) + obj = obj->package.elements; + else { + ACPI_ERROR((AE_INFO, "Invalid argument type")); + kfree(buffer.pointer); + return -EIO; + } + + if (obj->type != ACPI_TYPE_INTEGER) { + ACPI_ERROR((AE_INFO, "Invalid argument type")); + kfree(buffer.pointer); + return -EIO; + } else + ACPI_DEBUG_PRINT((ACPI_DB_INFO, "SMBus CMI Version %x" + "\n", (int)obj->integer.value)); + + kfree(buffer.pointer); + smbus_cmi->cap_info = 1; + } else if (!strcmp(name, smbus_methods.mt_sbr)) + smbus_cmi->cap_read = 1; + else if (!strcmp(name, smbus_methods.mt_sbw)) + smbus_cmi->cap_write = 1; + else + ACPI_DEBUG_PRINT((ACPI_DB_INFO, "Unsupported CMI method: %s\n", + name)); + + return 0; +} + +static acpi_status acpi_smbus_cmi_query_methods(acpi_handle handle, u32 level, + void *context, void **return_value) +{ + char node_name[5]; + struct acpi_buffer buffer = { sizeof(node_name), node_name }; + struct acpi_smbus_cmi *smbus_cmi = context; + acpi_status status; + + status = acpi_get_name(handle, ACPI_SINGLE_NAME, &buffer); + + if (ACPI_SUCCESS(status)) + acpi_smbus_cmi_add_cap(smbus_cmi, node_name); + + return AE_OK; +} + +static int acpi_smbus_cmi_add(struct acpi_device *device) +{ + struct acpi_smbus_cmi *smbus_cmi; + + smbus_cmi = kzalloc(sizeof(struct acpi_smbus_cmi), GFP_KERNEL); + if (!smbus_cmi) + return -ENOMEM; + + smbus_cmi->handle = device->handle; + strcpy(acpi_device_name(device), ACPI_SMBUS_HC_DEVICE_NAME); + strcpy(acpi_device_class(device), ACPI_SMBUS_HC_CLASS); + device->driver_data = smbus_cmi; + smbus_cmi->cap_info = 0; + smbus_cmi->cap_read = 0; + smbus_cmi->cap_write = 0; + + acpi_walk_namespace(ACPI_TYPE_METHOD, smbus_cmi->handle, 1, + acpi_smbus_cmi_query_methods, smbus_cmi, NULL); + + if (smbus_cmi->cap_info == 0) + goto err; + + snprintf(smbus_cmi->adapter.name, sizeof(smbus_cmi->adapter.name), + "SMBus CMI adapter %s (%s)", + acpi_device_name(device), + acpi_device_uid(device)); + smbus_cmi->adapter.owner = THIS_MODULE; + smbus_cmi->adapter.algo = &acpi_smbus_cmi_algorithm; + smbus_cmi->adapter.algo_data = smbus_cmi; + smbus_cmi->adapter.class = I2C_CLASS_HWMON | I2C_CLASS_SPD; + smbus_cmi->adapter.dev.parent = &device->dev; + + if (i2c_add_adapter(&smbus_cmi->adapter)) { + dev_err(&device->dev, "Couldn't register adapter!\n"); + goto err; + } + + return 0; + +err: + kfree(smbus_cmi); + device->driver_data = NULL; + return -EIO; +} + +static int acpi_smbus_cmi_remove(struct acpi_device *device, int type) +{ + struct acpi_smbus_cmi *smbus_cmi = acpi_driver_data(device); + + i2c_del_adapter(&smbus_cmi->adapter); + kfree(smbus_cmi); + device->driver_data = NULL; + + return 0; +} + +static struct acpi_driver acpi_smbus_cmi_driver = { + .name = ACPI_SMBUS_HC_DEVICE_NAME, + .class = ACPI_SMBUS_HC_CLASS, + .ids = acpi_smbus_cmi_ids, + .ops = { + .add = acpi_smbus_cmi_add, + .remove = acpi_smbus_cmi_remove, + }, +}; + +static int __init acpi_smbus_cmi_init(void) +{ + return acpi_bus_register_driver(&acpi_smbus_cmi_driver); +} + +static void __exit acpi_smbus_cmi_exit(void) +{ + acpi_bus_unregister_driver(&acpi_smbus_cmi_driver); +} + +module_init(acpi_smbus_cmi_init); +module_exit(acpi_smbus_cmi_exit); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Crane Cai "); +MODULE_DESCRIPTION("ACPI SMBus CMI driver"); diff --git a/drivers/i2c/busses/i2c-taos-evm.c b/drivers/i2c/busses/i2c-taos-evm.c index 224aa12ee7c..dd39c1eb03e 100644 --- a/drivers/i2c/busses/i2c-taos-evm.c +++ b/drivers/i2c/busses/i2c-taos-evm.c @@ -32,10 +32,12 @@ #define TAOS_STATE_INIT 0 #define TAOS_STATE_IDLE 1 -#define TAOS_STATE_SEND 2 +#define TAOS_STATE_EOFF 2 #define TAOS_STATE_RECV 3 #define TAOS_CMD_RESET 0x12 +#define TAOS_CMD_ECHO_ON '+' +#define TAOS_CMD_ECHO_OFF '-' static DECLARE_WAIT_QUEUE_HEAD(wq); @@ -102,17 +104,9 @@ static int taos_smbus_xfer(struct i2c_adapter *adapter, u16 addr, /* Send the transaction to the TAOS EVM */ dev_dbg(&adapter->dev, "Command buffer: %s\n", taos->buffer); - taos->pos = 0; - taos->state = TAOS_STATE_SEND; - serio_write(serio, taos->buffer[0]); - wait_event_interruptible_timeout(wq, taos->state == TAOS_STATE_IDLE, - msecs_to_jiffies(250)); - if (taos->state != TAOS_STATE_IDLE) { - dev_err(&adapter->dev, "Transaction failed " - "(state=%d, pos=%d)\n", taos->state, taos->pos); - taos->addr = 0; - return -EIO; - } + for (p = taos->buffer; *p; p++) + serio_write(serio, *p); + taos->addr = addr; /* Start the transaction and read the answer */ @@ -122,7 +116,7 @@ static int taos_smbus_xfer(struct i2c_adapter *adapter, u16 addr, wait_event_interruptible_timeout(wq, taos->state == TAOS_STATE_IDLE, msecs_to_jiffies(150)); if (taos->state != TAOS_STATE_IDLE - || taos->pos != 6) { + || taos->pos != 5) { dev_err(&adapter->dev, "Transaction timeout (pos=%d)\n", taos->pos); return -EIO; @@ -130,7 +124,7 @@ static int taos_smbus_xfer(struct i2c_adapter *adapter, u16 addr, dev_dbg(&adapter->dev, "Answer buffer: %s\n", taos->buffer); /* Interpret the returned string */ - p = taos->buffer + 2; + p = taos->buffer + 1; p[3] = '\0'; if (!strcmp(p, "NAK")) return -ENODEV; @@ -173,13 +167,9 @@ static irqreturn_t taos_interrupt(struct serio *serio, unsigned char data, wake_up_interruptible(&wq); } break; - case TAOS_STATE_SEND: - if (taos->buffer[++taos->pos]) - serio_write(serio, taos->buffer[taos->pos]); - else { - taos->state = TAOS_STATE_IDLE; - wake_up_interruptible(&wq); - } + case TAOS_STATE_EOFF: + taos->state = TAOS_STATE_IDLE; + wake_up_interruptible(&wq); break; case TAOS_STATE_RECV: taos->buffer[taos->pos++] = data; @@ -257,6 +247,19 @@ static int taos_connect(struct serio *serio, struct serio_driver *drv) } strlcpy(adapter->name, name, sizeof(adapter->name)); + /* Turn echo off for better performance */ + taos->state = TAOS_STATE_EOFF; + serio_write(serio, TAOS_CMD_ECHO_OFF); + + wait_event_interruptible_timeout(wq, taos->state == TAOS_STATE_IDLE, + msecs_to_jiffies(250)); + if (taos->state != TAOS_STATE_IDLE) { + err = -ENODEV; + dev_err(&adapter->dev, "Echo off failed " + "(state=%d)\n", taos->state); + goto exit_close; + } + err = i2c_add_adapter(adapter); if (err) goto exit_close; diff --git a/drivers/i2c/busses/scx200_acb.c b/drivers/i2c/busses/scx200_acb.c index 648ecc6f60e..cf994bd01d9 100644 --- a/drivers/i2c/busses/scx200_acb.c +++ b/drivers/i2c/busses/scx200_acb.c @@ -217,8 +217,10 @@ static void scx200_acb_machine(struct scx200_acb_iface *iface, u8 status) return; error: - dev_err(&iface->adapter.dev, "%s in state %s\n", errmsg, - scx200_acb_state_name[iface->state]); + dev_err(&iface->adapter.dev, + "%s in state %s (addr=0x%02x, len=%d, status=0x%02x)\n", errmsg, + scx200_acb_state_name[iface->state], iface->address_byte, + iface->len, status); iface->state = state_idle; iface->result = -EIO; diff --git a/drivers/i2c/chips/Kconfig b/drivers/i2c/chips/Kconfig index 02d746c9c47..f9618f4d4e4 100644 --- a/drivers/i2c/chips/Kconfig +++ b/drivers/i2c/chips/Kconfig @@ -16,54 +16,6 @@ config DS1682 This driver can also be built as a module. If so, the module will be called ds1682. -config SENSORS_PCF8574 - tristate "Philips PCF8574 and PCF8574A (DEPRECATED)" - depends on EXPERIMENTAL && GPIO_PCF857X = "n" - default n - help - If you say yes here you get support for Philips PCF8574 and - PCF8574A chips. These chips are 8-bit I/O expanders for the I2C bus. - - This driver can also be built as a module. If so, the module - will be called pcf8574. - - This driver is deprecated and will be dropped soon. Use - drivers/gpio/pcf857x.c instead. - - These devices are hard to detect and rarely found on mainstream - hardware. If unsure, say N. - -config PCF8575 - tristate "Philips PCF8575 (DEPRECATED)" - default n - depends on GPIO_PCF857X = "n" - help - If you say yes here you get support for Philips PCF8575 chip. - This chip is a 16-bit I/O expander for the I2C bus. Several other - chip manufacturers sell equivalent chips, e.g. Texas Instruments. - - This driver can also be built as a module. If so, the module - will be called pcf8575. - - This driver is deprecated and will be dropped soon. Use - drivers/gpio/pcf857x.c instead. - - This device is hard to detect and is rarely found on mainstream - hardware. If unsure, say N. - -config SENSORS_PCA9539 - tristate "Philips PCA9539 16-bit I/O port (DEPRECATED)" - depends on EXPERIMENTAL && GPIO_PCA953X = "n" - help - If you say yes here you get support for the Philips PCA9539 - 16-bit I/O port. - - This driver can also be built as a module. If so, the module - will be called pca9539. - - This driver is deprecated and will be dropped soon. Use - drivers/gpio/pca953x.c instead. - config SENSORS_TSL2550 tristate "Taos TSL2550 ambient light sensor" depends on EXPERIMENTAL diff --git a/drivers/i2c/chips/Makefile b/drivers/i2c/chips/Makefile index f4680d16ee3..749cf360629 100644 --- a/drivers/i2c/chips/Makefile +++ b/drivers/i2c/chips/Makefile @@ -11,9 +11,6 @@ # obj-$(CONFIG_DS1682) += ds1682.o -obj-$(CONFIG_SENSORS_PCA9539) += pca9539.o -obj-$(CONFIG_SENSORS_PCF8574) += pcf8574.o -obj-$(CONFIG_PCF8575) += pcf8575.o obj-$(CONFIG_SENSORS_TSL2550) += tsl2550.o ifeq ($(CONFIG_I2C_DEBUG_CHIP),y) diff --git a/drivers/i2c/chips/pca9539.c b/drivers/i2c/chips/pca9539.c deleted file mode 100644 index 270de4e56a8..00000000000 --- a/drivers/i2c/chips/pca9539.c +++ /dev/null @@ -1,152 +0,0 @@ -/* - pca9539.c - 16-bit I/O port with interrupt and reset - - Copyright (C) 2005 Ben Gardner - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; version 2 of the License. -*/ - -#include -#include -#include -#include -#include - -/* Addresses to scan: none, device is not autodetected */ -static const unsigned short normal_i2c[] = { I2C_CLIENT_END }; - -/* Insmod parameters */ -I2C_CLIENT_INSMOD_1(pca9539); - -enum pca9539_cmd -{ - PCA9539_INPUT_0 = 0, - PCA9539_INPUT_1 = 1, - PCA9539_OUTPUT_0 = 2, - PCA9539_OUTPUT_1 = 3, - PCA9539_INVERT_0 = 4, - PCA9539_INVERT_1 = 5, - PCA9539_DIRECTION_0 = 6, - PCA9539_DIRECTION_1 = 7, -}; - -/* following are the sysfs callback functions */ -static ssize_t pca9539_show(struct device *dev, struct device_attribute *attr, - char *buf) -{ - struct sensor_device_attribute *psa = to_sensor_dev_attr(attr); - struct i2c_client *client = to_i2c_client(dev); - return sprintf(buf, "%d\n", i2c_smbus_read_byte_data(client, - psa->index)); -} - -static ssize_t pca9539_store(struct device *dev, struct device_attribute *attr, - const char *buf, size_t count) -{ - struct sensor_device_attribute *psa = to_sensor_dev_attr(attr); - struct i2c_client *client = to_i2c_client(dev); - unsigned long val = simple_strtoul(buf, NULL, 0); - if (val > 0xff) - return -EINVAL; - i2c_smbus_write_byte_data(client, psa->index, val); - return count; -} - -/* Define the device attributes */ - -#define PCA9539_ENTRY_RO(name, cmd_idx) \ - static SENSOR_DEVICE_ATTR(name, S_IRUGO, pca9539_show, NULL, cmd_idx) - -#define PCA9539_ENTRY_RW(name, cmd_idx) \ - static SENSOR_DEVICE_ATTR(name, S_IRUGO | S_IWUSR, pca9539_show, \ - pca9539_store, cmd_idx) - -PCA9539_ENTRY_RO(input0, PCA9539_INPUT_0); -PCA9539_ENTRY_RO(input1, PCA9539_INPUT_1); -PCA9539_ENTRY_RW(output0, PCA9539_OUTPUT_0); -PCA9539_ENTRY_RW(output1, PCA9539_OUTPUT_1); -PCA9539_ENTRY_RW(invert0, PCA9539_INVERT_0); -PCA9539_ENTRY_RW(invert1, PCA9539_INVERT_1); -PCA9539_ENTRY_RW(direction0, PCA9539_DIRECTION_0); -PCA9539_ENTRY_RW(direction1, PCA9539_DIRECTION_1); - -static struct attribute *pca9539_attributes[] = { - &sensor_dev_attr_input0.dev_attr.attr, - &sensor_dev_attr_input1.dev_attr.attr, - &sensor_dev_attr_output0.dev_attr.attr, - &sensor_dev_attr_output1.dev_attr.attr, - &sensor_dev_attr_invert0.dev_attr.attr, - &sensor_dev_attr_invert1.dev_attr.attr, - &sensor_dev_attr_direction0.dev_attr.attr, - &sensor_dev_attr_direction1.dev_attr.attr, - NULL -}; - -static struct attribute_group pca9539_defattr_group = { - .attrs = pca9539_attributes, -}; - -/* Return 0 if detection is successful, -ENODEV otherwise */ -static int pca9539_detect(struct i2c_client *client, int kind, - struct i2c_board_info *info) -{ - struct i2c_adapter *adapter = client->adapter; - - if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) - return -ENODEV; - - strlcpy(info->type, "pca9539", I2C_NAME_SIZE); - - return 0; -} - -static int pca9539_probe(struct i2c_client *client, - const struct i2c_device_id *id) -{ - /* Register sysfs hooks */ - return sysfs_create_group(&client->dev.kobj, - &pca9539_defattr_group); -} - -static int pca9539_remove(struct i2c_client *client) -{ - sysfs_remove_group(&client->dev.kobj, &pca9539_defattr_group); - return 0; -} - -static const struct i2c_device_id pca9539_id[] = { - { "pca9539", 0 }, - { } -}; - -static struct i2c_driver pca9539_driver = { - .driver = { - .name = "pca9539", - }, - .probe = pca9539_probe, - .remove = pca9539_remove, - .id_table = pca9539_id, - - .detect = pca9539_detect, - .address_data = &addr_data, -}; - -static int __init pca9539_init(void) -{ - return i2c_add_driver(&pca9539_driver); -} - -static void __exit pca9539_exit(void) -{ - i2c_del_driver(&pca9539_driver); -} - -MODULE_AUTHOR("Ben Gardner "); -MODULE_DESCRIPTION("PCA9539 driver"); -MODULE_LICENSE("GPL"); - -module_init(pca9539_init); -module_exit(pca9539_exit); - diff --git a/drivers/i2c/chips/pcf8574.c b/drivers/i2c/chips/pcf8574.c deleted file mode 100644 index 6ec309894c8..00000000000 --- a/drivers/i2c/chips/pcf8574.c +++ /dev/null @@ -1,215 +0,0 @@ -/* - Copyright (c) 2000 Frodo Looijaard , - Philip Edelbrock , - Dan Eaton - Ported to Linux 2.6 by Aurelien Jarno with - the help of Jean Delvare - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; either version 2 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. -*/ - -/* A few notes about the PCF8574: - -* The PCF8574 is an 8-bit I/O expander for the I2C bus produced by - Philips Semiconductors. It is designed to provide a byte I2C - interface to up to 8 separate devices. - -* The PCF8574 appears as a very simple SMBus device which can be - read from or written to with SMBUS byte read/write accesses. - - --Dan - -*/ - -#include -#include -#include -#include - -/* Addresses to scan: none, device can't be detected */ -static const unsigned short normal_i2c[] = { I2C_CLIENT_END }; - -/* Insmod parameters */ -I2C_CLIENT_INSMOD_2(pcf8574, pcf8574a); - -/* Each client has this additional data */ -struct pcf8574_data { - int write; /* Remember last written value */ -}; - -static void pcf8574_init_client(struct i2c_client *client); - -/* following are the sysfs callback functions */ -static ssize_t show_read(struct device *dev, struct device_attribute *attr, char *buf) -{ - struct i2c_client *client = to_i2c_client(dev); - return sprintf(buf, "%u\n", i2c_smbus_read_byte(client)); -} - -static DEVICE_ATTR(read, S_IRUGO, show_read, NULL); - -static ssize_t show_write(struct device *dev, struct device_attribute *attr, char *buf) -{ - struct pcf8574_data *data = i2c_get_clientdata(to_i2c_client(dev)); - - if (data->write < 0) - return data->write; - - return sprintf(buf, "%d\n", data->write); -} - -static ssize_t set_write(struct device *dev, struct device_attribute *attr, const char *buf, - size_t count) -{ - struct i2c_client *client = to_i2c_client(dev); - struct pcf8574_data *data = i2c_get_clientdata(client); - unsigned long val = simple_strtoul(buf, NULL, 10); - - if (val > 0xff) - return -EINVAL; - - data->write = val; - i2c_smbus_write_byte(client, data->write); - return count; -} - -static DEVICE_ATTR(write, S_IWUSR | S_IRUGO, show_write, set_write); - -static struct attribute *pcf8574_attributes[] = { - &dev_attr_read.attr, - &dev_attr_write.attr, - NULL -}; - -static const struct attribute_group pcf8574_attr_group = { - .attrs = pcf8574_attributes, -}; - -/* - * Real code - */ - -/* Return 0 if detection is successful, -ENODEV otherwise */ -static int pcf8574_detect(struct i2c_client *client, int kind, - struct i2c_board_info *info) -{ - struct i2c_adapter *adapter = client->adapter; - const char *client_name; - - if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE)) - return -ENODEV; - - /* Now, we would do the remaining detection. But the PCF8574 is plainly - impossible to detect! Stupid chip. */ - - /* Determine the chip type */ - if (kind <= 0) { - if (client->addr >= 0x38 && client->addr <= 0x3f) - kind = pcf8574a; - else - kind = pcf8574; - } - - if (kind == pcf8574a) - client_name = "pcf8574a"; - else - client_name = "pcf8574"; - strlcpy(info->type, client_name, I2C_NAME_SIZE); - - return 0; -} - -static int pcf8574_probe(struct i2c_client *client, - const struct i2c_device_id *id) -{ - struct pcf8574_data *data; - int err; - - data = kzalloc(sizeof(struct pcf8574_data), GFP_KERNEL); - if (!data) { - err = -ENOMEM; - goto exit; - } - - i2c_set_clientdata(client, data); - - /* Initialize the PCF8574 chip */ - pcf8574_init_client(client); - - /* Register sysfs hooks */ - err = sysfs_create_group(&client->dev.kobj, &pcf8574_attr_group); - if (err) - goto exit_free; - return 0; - - exit_free: - kfree(data); - exit: - return err; -} - -static int pcf8574_remove(struct i2c_client *client) -{ - sysfs_remove_group(&client->dev.kobj, &pcf8574_attr_group); - kfree(i2c_get_clientdata(client)); - return 0; -} - -/* Called when we have found a new PCF8574. */ -static void pcf8574_init_client(struct i2c_client *client) -{ - struct pcf8574_data *data = i2c_get_clientdata(client); - data->write = -EAGAIN; -} - -static const struct i2c_device_id pcf8574_id[] = { - { "pcf8574", 0 }, - { "pcf8574a", 0 }, - { } -}; - -static struct i2c_driver pcf8574_driver = { - .driver = { - .name = "pcf8574", - }, - .probe = pcf8574_probe, - .remove = pcf8574_remove, - .id_table = pcf8574_id, - - .detect = pcf8574_detect, - .address_data = &addr_data, -}; - -static int __init pcf8574_init(void) -{ - return i2c_add_driver(&pcf8574_driver); -} - -static void __exit pcf8574_exit(void) -{ - i2c_del_driver(&pcf8574_driver); -} - - -MODULE_AUTHOR - ("Frodo Looijaard , " - "Philip Edelbrock , " - "Dan Eaton " - "and Aurelien Jarno "); -MODULE_DESCRIPTION("PCF8574 driver"); -MODULE_LICENSE("GPL"); - -module_init(pcf8574_init); -module_exit(pcf8574_exit); diff --git a/drivers/i2c/chips/pcf8575.c b/drivers/i2c/chips/pcf8575.c deleted file mode 100644 index 07fd7cb3c57..00000000000 --- a/drivers/i2c/chips/pcf8575.c +++ /dev/null @@ -1,198 +0,0 @@ -/* - pcf8575.c - - About the PCF8575 chip: the PCF8575 is a 16-bit I/O expander for the I2C bus - produced by a.o. Philips Semiconductors. - - Copyright (C) 2006 Michael Hennerich, Analog Devices Inc. - - Based on pcf8574.c. - - Copyright (c) 2007 Bart Van Assche . - Ported this driver from ucLinux to the mainstream Linux kernel. - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; either version 2 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. -*/ - -#include -#include -#include -#include /* kzalloc() */ -#include /* sysfs_create_group() */ - -/* Addresses to scan: none, device can't be detected */ -static const unsigned short normal_i2c[] = { I2C_CLIENT_END }; - -/* Insmod parameters */ -I2C_CLIENT_INSMOD; - - -/* Each client has this additional data */ -struct pcf8575_data { - int write; /* last written value, or error code */ -}; - -/* following are the sysfs callback functions */ -static ssize_t show_read(struct device *dev, struct device_attribute *attr, - char *buf) -{ - struct i2c_client *client = to_i2c_client(dev); - u16 val; - u8 iopin_state[2]; - - i2c_master_recv(client, iopin_state, 2); - - val = iopin_state[0]; - val |= iopin_state[1] << 8; - - return sprintf(buf, "%u\n", val); -} - -static DEVICE_ATTR(read, S_IRUGO, show_read, NULL); - -static ssize_t show_write(struct device *dev, struct device_attribute *attr, - char *buf) -{ - struct pcf8575_data *data = dev_get_drvdata(dev); - if (data->write < 0) - return data->write; - return sprintf(buf, "%d\n", data->write); -} - -static ssize_t set_write(struct device *dev, struct device_attribute *attr, - const char *buf, size_t count) -{ - struct i2c_client *client = to_i2c_client(dev); - struct pcf8575_data *data = i2c_get_clientdata(client); - unsigned long val = simple_strtoul(buf, NULL, 10); - u8 iopin_state[2]; - - if (val > 0xffff) - return -EINVAL; - - data->write = val; - - iopin_state[0] = val & 0xFF; - iopin_state[1] = val >> 8; - - i2c_master_send(client, iopin_state, 2); - - return count; -} - -static DEVICE_ATTR(write, S_IWUSR | S_IRUGO, show_write, set_write); - -static struct attribute *pcf8575_attributes[] = { - &dev_attr_read.attr, - &dev_attr_write.attr, - NULL -}; - -static const struct attribute_group pcf8575_attr_group = { - .attrs = pcf8575_attributes, -}; - -/* - * Real code - */ - -/* Return 0 if detection is successful, -ENODEV otherwise */ -static int pcf8575_detect(struct i2c_client *client, int kind, - struct i2c_board_info *info) -{ - struct i2c_adapter *adapter = client->adapter; - - if (!i2c_check_functionality(adapter, I2C_FUNC_I2C)) - return -ENODEV; - - /* This is the place to detect whether the chip at the specified - address really is a PCF8575 chip. However, there is no method known - to detect whether an I2C chip is a PCF8575 or any other I2C chip. */ - - strlcpy(info->type, "pcf8575", I2C_NAME_SIZE); - - return 0; -} - -static int pcf8575_probe(struct i2c_client *client, - const struct i2c_device_id *id) -{ - struct pcf8575_data *data; - int err; - - data = kzalloc(sizeof(struct pcf8575_data), GFP_KERNEL); - if (!data) { - err = -ENOMEM; - goto exit; - } - - i2c_set_clientdata(client, data); - data->write = -EAGAIN; - - /* Register sysfs hooks */ - err = sysfs_create_group(&client->dev.kobj, &pcf8575_attr_group); - if (err) - goto exit_free; - - return 0; - -exit_free: - kfree(data); -exit: - return err; -} - -static int pcf8575_remove(struct i2c_client *client) -{ - sysfs_remove_group(&client->dev.kobj, &pcf8575_attr_group); - kfree(i2c_get_clientdata(client)); - return 0; -} - -static const struct i2c_device_id pcf8575_id[] = { - { "pcf8575", 0 }, - { } -}; - -static struct i2c_driver pcf8575_driver = { - .driver = { - .owner = THIS_MODULE, - .name = "pcf8575", - }, - .probe = pcf8575_probe, - .remove = pcf8575_remove, - .id_table = pcf8575_id, - - .detect = pcf8575_detect, - .address_data = &addr_data, -}; - -static int __init pcf8575_init(void) -{ - return i2c_add_driver(&pcf8575_driver); -} - -static void __exit pcf8575_exit(void) -{ - i2c_del_driver(&pcf8575_driver); -} - -MODULE_AUTHOR("Michael Hennerich , " - "Bart Van Assche "); -MODULE_DESCRIPTION("pcf8575 driver"); -MODULE_LICENSE("GPL"); - -module_init(pcf8575_init); -module_exit(pcf8575_exit); diff --git a/drivers/i2c/chips/tsl2550.c b/drivers/i2c/chips/tsl2550.c index b96f3025e58..aa96bd2d27e 100644 --- a/drivers/i2c/chips/tsl2550.c +++ b/drivers/i2c/chips/tsl2550.c @@ -24,10 +24,9 @@ #include #include #include -#include #define TSL2550_DRV_NAME "tsl2550" -#define DRIVER_VERSION "1.1.2" +#define DRIVER_VERSION "1.2" /* * Defines @@ -96,32 +95,13 @@ static int tsl2550_set_power_state(struct i2c_client *client, int state) static int tsl2550_get_adc_value(struct i2c_client *client, u8 cmd) { - unsigned long end; - int loop = 0, ret = 0; + int ret; - /* - * Read ADC channel waiting at most 400ms (see data sheet for further - * info). - * To avoid long busy wait we spin for few milliseconds then - * start sleeping. - */ - end = jiffies + msecs_to_jiffies(400); - while (time_before(jiffies, end)) { - i2c_smbus_write_byte(client, cmd); - - if (loop++ < 5) - mdelay(1); - else - msleep(1); - - ret = i2c_smbus_read_byte(client); - if (ret < 0) - return ret; - else if (ret & 0x0080) - break; - } + ret = i2c_smbus_read_byte_data(client, cmd); + if (ret < 0) + return ret; if (!(ret & 0x80)) - return -EIO; + return -EAGAIN; return ret & 0x7f; /* remove the "valid" bit */ } @@ -285,8 +265,6 @@ static ssize_t __tsl2550_show_lux(struct i2c_client *client, char *buf) return ret; ch0 = ret; - mdelay(1); - ret = tsl2550_get_adc_value(client, TSL2550_READ_ADC1); if (ret < 0) return ret; @@ -345,11 +323,10 @@ static int tsl2550_init_client(struct i2c_client *client) * Probe the chip. To do so we try to power up the device and then to * read back the 0x03 code */ - err = i2c_smbus_write_byte(client, TSL2550_POWER_UP); + err = i2c_smbus_read_byte_data(client, TSL2550_POWER_UP); if (err < 0) return err; - mdelay(1); - if (i2c_smbus_read_byte(client) != TSL2550_POWER_UP) + if (err != TSL2550_POWER_UP) return -ENODEV; data->power_state = 1; @@ -374,7 +351,8 @@ static int __devinit tsl2550_probe(struct i2c_client *client, struct tsl2550_data *data; int *opmode, err = 0; - if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE)) { + if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_WRITE_BYTE + | I2C_FUNC_SMBUS_READ_BYTE_DATA)) { err = -EIO; goto exit; } diff --git a/drivers/i2c/i2c-core.c b/drivers/i2c/i2c-core.c index 0e45c296d3d..8d80fceca6a 100644 --- a/drivers/i2c/i2c-core.c +++ b/drivers/i2c/i2c-core.c @@ -46,6 +46,7 @@ static DEFINE_MUTEX(core_lock); static DEFINE_IDR(i2c_adapter_idr); static LIST_HEAD(userspace_devices); +static struct device_type i2c_client_type; static int i2c_check_addr(struct i2c_adapter *adapter, int addr); static int i2c_detect(struct i2c_adapter *adapter, struct i2c_driver *driver); @@ -64,9 +65,13 @@ static const struct i2c_device_id *i2c_match_id(const struct i2c_device_id *id, static int i2c_device_match(struct device *dev, struct device_driver *drv) { - struct i2c_client *client = to_i2c_client(dev); - struct i2c_driver *driver = to_i2c_driver(drv); + struct i2c_client *client = i2c_verify_client(dev); + struct i2c_driver *driver; + if (!client) + return 0; + + driver = to_i2c_driver(drv); /* match on an id table if there is one */ if (driver->id_table) return i2c_match_id(driver->id_table, client) != NULL; @@ -94,10 +99,14 @@ static int i2c_device_uevent(struct device *dev, struct kobj_uevent_env *env) static int i2c_device_probe(struct device *dev) { - struct i2c_client *client = to_i2c_client(dev); - struct i2c_driver *driver = to_i2c_driver(dev->driver); + struct i2c_client *client = i2c_verify_client(dev); + struct i2c_driver *driver; int status; + if (!client) + return 0; + + driver = to_i2c_driver(dev->driver); if (!driver->probe || !driver->id_table) return -ENODEV; client->driver = driver; @@ -114,11 +123,11 @@ static int i2c_device_probe(struct device *dev) static int i2c_device_remove(struct device *dev) { - struct i2c_client *client = to_i2c_client(dev); + struct i2c_client *client = i2c_verify_client(dev); struct i2c_driver *driver; int status; - if (!dev->driver) + if (!client || !dev->driver) return 0; driver = to_i2c_driver(dev->driver); @@ -136,37 +145,40 @@ static int i2c_device_remove(struct device *dev) static void i2c_device_shutdown(struct device *dev) { + struct i2c_client *client = i2c_verify_client(dev); struct i2c_driver *driver; - if (!dev->driver) + if (!client || !dev->driver) return; driver = to_i2c_driver(dev->driver); if (driver->shutdown) - driver->shutdown(to_i2c_client(dev)); + driver->shutdown(client); } static int i2c_device_suspend(struct device *dev, pm_message_t mesg) { + struct i2c_client *client = i2c_verify_client(dev); struct i2c_driver *driver; - if (!dev->driver) + if (!client || !dev->driver) return 0; driver = to_i2c_driver(dev->driver); if (!driver->suspend) return 0; - return driver->suspend(to_i2c_client(dev), mesg); + return driver->suspend(client, mesg); } static int i2c_device_resume(struct device *dev) { + struct i2c_client *client = i2c_verify_client(dev); struct i2c_driver *driver; - if (!dev->driver) + if (!client || !dev->driver) return 0; driver = to_i2c_driver(dev->driver); if (!driver->resume) return 0; - return driver->resume(to_i2c_client(dev)); + return driver->resume(client); } static void i2c_client_dev_release(struct device *dev) @@ -175,10 +187,10 @@ static void i2c_client_dev_release(struct device *dev) } static ssize_t -show_client_name(struct device *dev, struct device_attribute *attr, char *buf) +show_name(struct device *dev, struct device_attribute *attr, char *buf) { - struct i2c_client *client = to_i2c_client(dev); - return sprintf(buf, "%s\n", client->name); + return sprintf(buf, "%s\n", dev->type == &i2c_client_type ? + to_i2c_client(dev)->name : to_i2c_adapter(dev)->name); } static ssize_t @@ -188,18 +200,28 @@ show_modalias(struct device *dev, struct device_attribute *attr, char *buf) return sprintf(buf, "%s%s\n", I2C_MODULE_PREFIX, client->name); } -static struct device_attribute i2c_dev_attrs[] = { - __ATTR(name, S_IRUGO, show_client_name, NULL), +static DEVICE_ATTR(name, S_IRUGO, show_name, NULL); +static DEVICE_ATTR(modalias, S_IRUGO, show_modalias, NULL); + +static struct attribute *i2c_dev_attrs[] = { + &dev_attr_name.attr, /* modalias helps coldplug: modprobe $(cat .../modalias) */ - __ATTR(modalias, S_IRUGO, show_modalias, NULL), - { }, + &dev_attr_modalias.attr, + NULL +}; + +static struct attribute_group i2c_dev_attr_group = { + .attrs = i2c_dev_attrs, +}; + +static const struct attribute_group *i2c_dev_attr_groups[] = { + &i2c_dev_attr_group, + NULL }; struct bus_type i2c_bus_type = { .name = "i2c", - .dev_attrs = i2c_dev_attrs, .match = i2c_device_match, - .uevent = i2c_device_uevent, .probe = i2c_device_probe, .remove = i2c_device_remove, .shutdown = i2c_device_shutdown, @@ -208,6 +230,12 @@ struct bus_type i2c_bus_type = { }; EXPORT_SYMBOL_GPL(i2c_bus_type); +static struct device_type i2c_client_type = { + .groups = i2c_dev_attr_groups, + .uevent = i2c_device_uevent, + .release = i2c_client_dev_release, +}; + /** * i2c_verify_client - return parameter as i2c_client, or NULL @@ -220,7 +248,7 @@ EXPORT_SYMBOL_GPL(i2c_bus_type); */ struct i2c_client *i2c_verify_client(struct device *dev) { - return (dev->bus == &i2c_bus_type) + return (dev->type == &i2c_client_type) ? to_i2c_client(dev) : NULL; } @@ -273,7 +301,7 @@ i2c_new_device(struct i2c_adapter *adap, struct i2c_board_info const *info) client->dev.parent = &client->adapter->dev; client->dev.bus = &i2c_bus_type; - client->dev.release = i2c_client_dev_release; + client->dev.type = &i2c_client_type; dev_set_name(&client->dev, "%d-%04x", i2c_adapter_id(adap), client->addr); @@ -368,13 +396,6 @@ static void i2c_adapter_dev_release(struct device *dev) complete(&adap->dev_released); } -static ssize_t -show_adapter_name(struct device *dev, struct device_attribute *attr, char *buf) -{ - struct i2c_adapter *adap = to_i2c_adapter(dev); - return sprintf(buf, "%s\n", adap->name); -} - /* * Let users instantiate I2C devices through sysfs. This can be used when * platform initialization code doesn't contain the proper data for @@ -493,19 +514,34 @@ i2c_sysfs_delete_device(struct device *dev, struct device_attribute *attr, return res; } -static struct device_attribute i2c_adapter_attrs[] = { - __ATTR(name, S_IRUGO, show_adapter_name, NULL), - __ATTR(new_device, S_IWUSR, NULL, i2c_sysfs_new_device), - __ATTR(delete_device, S_IWUSR, NULL, i2c_sysfs_delete_device), - { }, +static DEVICE_ATTR(new_device, S_IWUSR, NULL, i2c_sysfs_new_device); +static DEVICE_ATTR(delete_device, S_IWUSR, NULL, i2c_sysfs_delete_device); + +static struct attribute *i2c_adapter_attrs[] = { + &dev_attr_name.attr, + &dev_attr_new_device.attr, + &dev_attr_delete_device.attr, + NULL }; -static struct class i2c_adapter_class = { - .owner = THIS_MODULE, - .name = "i2c-adapter", - .dev_attrs = i2c_adapter_attrs, +static struct attribute_group i2c_adapter_attr_group = { + .attrs = i2c_adapter_attrs, }; +static const struct attribute_group *i2c_adapter_attr_groups[] = { + &i2c_adapter_attr_group, + NULL +}; + +static struct device_type i2c_adapter_type = { + .groups = i2c_adapter_attr_groups, + .release = i2c_adapter_dev_release, +}; + +#ifdef CONFIG_I2C_COMPAT +static struct class_compat *i2c_adapter_compat_class; +#endif + static void i2c_scan_static_board_info(struct i2c_adapter *adapter) { struct i2c_devinfo *devinfo; @@ -555,14 +591,22 @@ static int i2c_register_adapter(struct i2c_adapter *adap) adap->timeout = HZ; dev_set_name(&adap->dev, "i2c-%d", adap->nr); - adap->dev.release = &i2c_adapter_dev_release; - adap->dev.class = &i2c_adapter_class; + adap->dev.bus = &i2c_bus_type; + adap->dev.type = &i2c_adapter_type; res = device_register(&adap->dev); if (res) goto out_list; dev_dbg(&adap->dev, "adapter [%s] registered\n", adap->name); +#ifdef CONFIG_I2C_COMPAT + res = class_compat_create_link(i2c_adapter_compat_class, &adap->dev, + adap->dev.parent); + if (res) + dev_warn(&adap->dev, + "Failed to create compatibility class link\n"); +#endif + /* create pre-declared device nodes */ if (adap->nr < __i2c_first_dynamic_bus_num) i2c_scan_static_board_info(adap); @@ -741,6 +785,11 @@ int i2c_del_adapter(struct i2c_adapter *adap) checking the returned value. */ res = device_for_each_child(&adap->dev, NULL, __unregister_client); +#ifdef CONFIG_I2C_COMPAT + class_compat_remove_link(i2c_adapter_compat_class, &adap->dev, + adap->dev.parent); +#endif + /* clean up the sysfs representation */ init_completion(&adap->dev_released); device_unregister(&adap->dev); @@ -768,9 +817,13 @@ EXPORT_SYMBOL(i2c_del_adapter); static int __attach_adapter(struct device *dev, void *data) { - struct i2c_adapter *adapter = to_i2c_adapter(dev); + struct i2c_adapter *adapter; struct i2c_driver *driver = data; + if (dev->type != &i2c_adapter_type) + return 0; + adapter = to_i2c_adapter(dev); + i2c_detect(adapter, driver); /* Legacy drivers scan i2c busses directly */ @@ -809,8 +862,7 @@ int i2c_register_driver(struct module *owner, struct i2c_driver *driver) INIT_LIST_HEAD(&driver->clients); /* Walk the adapters that are already present */ mutex_lock(&core_lock); - class_for_each_device(&i2c_adapter_class, NULL, driver, - __attach_adapter); + bus_for_each_dev(&i2c_bus_type, NULL, driver, __attach_adapter); mutex_unlock(&core_lock); return 0; @@ -819,10 +871,14 @@ EXPORT_SYMBOL(i2c_register_driver); static int __detach_adapter(struct device *dev, void *data) { - struct i2c_adapter *adapter = to_i2c_adapter(dev); + struct i2c_adapter *adapter; struct i2c_driver *driver = data; struct i2c_client *client, *_n; + if (dev->type != &i2c_adapter_type) + return 0; + adapter = to_i2c_adapter(dev); + /* Remove the devices we created ourselves as the result of hardware * probing (using a driver's detect method) */ list_for_each_entry_safe(client, _n, &driver->clients, detected) { @@ -850,8 +906,7 @@ static int __detach_adapter(struct device *dev, void *data) void i2c_del_driver(struct i2c_driver *driver) { mutex_lock(&core_lock); - class_for_each_device(&i2c_adapter_class, NULL, driver, - __detach_adapter); + bus_for_each_dev(&i2c_bus_type, NULL, driver, __detach_adapter); mutex_unlock(&core_lock); driver_unregister(&driver->driver); @@ -940,17 +995,23 @@ static int __init i2c_init(void) retval = bus_register(&i2c_bus_type); if (retval) return retval; - retval = class_register(&i2c_adapter_class); - if (retval) +#ifdef CONFIG_I2C_COMPAT + i2c_adapter_compat_class = class_compat_register("i2c-adapter"); + if (!i2c_adapter_compat_class) { + retval = -ENOMEM; goto bus_err; + } +#endif retval = i2c_add_driver(&dummy_driver); if (retval) goto class_err; return 0; class_err: - class_unregister(&i2c_adapter_class); +#ifdef CONFIG_I2C_COMPAT + class_compat_unregister(i2c_adapter_compat_class); bus_err: +#endif bus_unregister(&i2c_bus_type); return retval; } @@ -958,7 +1019,9 @@ bus_err: static void __exit i2c_exit(void) { i2c_del_driver(&dummy_driver); - class_unregister(&i2c_adapter_class); +#ifdef CONFIG_I2C_COMPAT + class_compat_unregister(i2c_adapter_compat_class); +#endif bus_unregister(&i2c_bus_type); } diff --git a/include/linux/i2c-id.h b/include/linux/i2c-id.h index c9087de5c6c..e844a0b1869 100644 --- a/include/linux/i2c-id.h +++ b/include/linux/i2c-id.h @@ -27,17 +27,6 @@ legacy chip driver needs to identify a bus or a bus driver needs to identify a legacy client. If you don't need them, just don't set them. */ -/* - * ---- Driver types ----------------------------------------------------- - */ - -#define I2C_DRIVERID_MSP3400 1 -#define I2C_DRIVERID_TUNER 2 -#define I2C_DRIVERID_TDA7432 27 /* Stereo sound processor */ -#define I2C_DRIVERID_TVAUDIO 29 /* Generic TV sound driver */ -#define I2C_DRIVERID_SAA711X 73 /* saa711x video encoders */ -#define I2C_DRIVERID_INFRARED 75 /* I2C InfraRed on Video boards */ - /* * ---- Adapter types ---------------------------------------------------- */ diff --git a/include/linux/i2c.h b/include/linux/i2c.h index f4784c0fe97..57d41b0abce 100644 --- a/include/linux/i2c.h +++ b/include/linux/i2c.h @@ -98,7 +98,6 @@ extern s32 i2c_smbus_write_i2c_block_data(struct i2c_client *client, /** * struct i2c_driver - represent an I2C device driver - * @id: Unique driver ID (optional) * @class: What kind of i2c device we instantiate (for detect) * @attach_adapter: Callback for bus addition (for legacy drivers) * @detach_adapter: Callback for bus removal (for legacy drivers) @@ -135,7 +134,6 @@ extern s32 i2c_smbus_write_i2c_block_data(struct i2c_client *client, * not allowed. */ struct i2c_driver { - int id; unsigned int class; /* Notifies the driver that a new bus has appeared or is about to be diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h index 3b6b788fe2b..7803565aa87 100644 --- a/include/linux/pci_ids.h +++ b/include/linux/pci_ids.h @@ -543,6 +543,7 @@ #define PCI_DEVICE_ID_AMD_8131_BRIDGE 0x7450 #define PCI_DEVICE_ID_AMD_8131_APIC 0x7451 #define PCI_DEVICE_ID_AMD_8132_BRIDGE 0x7458 +#define PCI_DEVICE_ID_AMD_SB900_SMBUS 0x780b #define PCI_DEVICE_ID_AMD_CS5535_IDE 0x208F #define PCI_DEVICE_ID_AMD_CS5536_ISA 0x2090 #define PCI_DEVICE_ID_AMD_CS5536_FLASH 0x2091