diff --git a/drivers/net/e1000e/defines.h b/drivers/net/e1000e/defines.h index 4741ef9ec38..1190167a8b3 100644 --- a/drivers/net/e1000e/defines.h +++ b/drivers/net/e1000e/defines.h @@ -76,6 +76,7 @@ /* Extended Device Control */ #define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Definable Pin 7 */ #define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */ +#define E1000_CTRL_EXT_SPD_BYPS 0x00008000 /* Speed Select Bypass */ #define E1000_CTRL_EXT_RO_DIS 0x00020000 /* Relaxed Ordering disable */ #define E1000_CTRL_EXT_DMA_DYN_CLK_EN 0x00080000 /* DMA Dynamic Clock Gating */ #define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000 diff --git a/drivers/net/e1000e/e1000.h b/drivers/net/e1000e/e1000.h index 405a144ebca..189dfa2d6c7 100644 --- a/drivers/net/e1000e/e1000.h +++ b/drivers/net/e1000e/e1000.h @@ -141,6 +141,20 @@ struct e1000_info; #define HV_TNCRS_UPPER PHY_REG(778, 29) /* Transmit with no CRS */ #define HV_TNCRS_LOWER PHY_REG(778, 30) +/* BM PHY Copper Specific Status */ +#define BM_CS_STATUS 17 +#define BM_CS_STATUS_LINK_UP 0x0400 +#define BM_CS_STATUS_RESOLVED 0x0800 +#define BM_CS_STATUS_SPEED_MASK 0xC000 +#define BM_CS_STATUS_SPEED_1000 0x8000 + +/* 82577 Mobile Phy Status Register */ +#define HV_M_STATUS 26 +#define HV_M_STATUS_AUTONEG_COMPLETE 0x1000 +#define HV_M_STATUS_SPEED_MASK 0x0300 +#define HV_M_STATUS_SPEED_1000 0x0200 +#define HV_M_STATUS_LINK_UP 0x0040 + enum e1000_boards { board_82571, board_82572, diff --git a/drivers/net/e1000e/hw.h b/drivers/net/e1000e/hw.h index 7b05cf47f7f..aaea41ef794 100644 --- a/drivers/net/e1000e/hw.h +++ b/drivers/net/e1000e/hw.h @@ -903,6 +903,7 @@ struct e1000_shadow_ram { struct e1000_dev_spec_ich8lan { bool kmrn_lock_loss_workaround_enabled; struct e1000_shadow_ram shadow_ram[E1000_ICH8_SHADOW_RAM_WORDS]; + bool nvm_k1_enabled; }; struct e1000_hw { diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c index 095ffa56ed9..51ddb04ab19 100644 --- a/drivers/net/e1000e/ich8lan.c +++ b/drivers/net/e1000e/ich8lan.c @@ -140,6 +140,9 @@ #define HV_OEM_BITS_GBE_DIS 0x0040 /* Gigabit Disable */ #define HV_OEM_BITS_RESTART_AN 0x0400 /* Restart Auto-negotiation */ +#define E1000_NVM_K1_CONFIG 0x1B /* NVM K1 Config Word */ +#define E1000_NVM_K1_ENABLE 0x1 /* NVM Enable K1 bit */ + /* ICH GbE Flash Hardware Sequencing Flash Status Register bit breakdown */ /* Offset 04h HSFSTS */ union ich8_hws_flash_status { @@ -220,6 +223,8 @@ static s32 e1000_led_on_pchlan(struct e1000_hw *hw); static s32 e1000_led_off_pchlan(struct e1000_hw *hw); static s32 e1000_set_lplu_state_pchlan(struct e1000_hw *hw, bool active); static void e1000_lan_init_done_ich8lan(struct e1000_hw *hw); +static s32 e1000_k1_gig_workaround_hv(struct e1000_hw *hw, bool link); +static s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable); static inline u16 __er16flash(struct e1000_hw *hw, unsigned long reg) { @@ -495,14 +500,6 @@ static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw) goto out; } - if (hw->mac.type == e1000_pchlan) { - ret_val = e1000e_write_kmrn_reg(hw, - E1000_KMRNCTRLSTA_K1_CONFIG, - E1000_KMRNCTRLSTA_K1_ENABLE); - if (ret_val) - goto out; - } - /* * First we want to see if the MII Status Register reports * link. If so, then we want to get the current speed/duplex @@ -512,6 +509,12 @@ static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw) if (ret_val) goto out; + if (hw->mac.type == e1000_pchlan) { + ret_val = e1000_k1_gig_workaround_hv(hw, link); + if (ret_val) + goto out; + } + if (!link) goto out; /* No link detected */ @@ -928,6 +931,141 @@ out: return ret_val; } +/** + * e1000_k1_gig_workaround_hv - K1 Si workaround + * @hw: pointer to the HW structure + * @link: link up bool flag + * + * If K1 is enabled for 1Gbps, the MAC might stall when transitioning + * from a lower speed. This workaround disables K1 whenever link is at 1Gig + * If link is down, the function will restore the default K1 setting located + * in the NVM. + **/ +static s32 e1000_k1_gig_workaround_hv(struct e1000_hw *hw, bool link) +{ + s32 ret_val = 0; + u16 status_reg = 0; + bool k1_enable = hw->dev_spec.ich8lan.nvm_k1_enabled; + + if (hw->mac.type != e1000_pchlan) + goto out; + + /* Wrap the whole flow with the sw flag */ + ret_val = hw->phy.ops.acquire_phy(hw); + if (ret_val) + goto out; + + /* Disable K1 when link is 1Gbps, otherwise use the NVM setting */ + if (link) { + if (hw->phy.type == e1000_phy_82578) { + ret_val = hw->phy.ops.read_phy_reg_locked(hw, + BM_CS_STATUS, + &status_reg); + if (ret_val) + goto release; + + status_reg &= BM_CS_STATUS_LINK_UP | + BM_CS_STATUS_RESOLVED | + BM_CS_STATUS_SPEED_MASK; + + if (status_reg == (BM_CS_STATUS_LINK_UP | + BM_CS_STATUS_RESOLVED | + BM_CS_STATUS_SPEED_1000)) + k1_enable = false; + } + + if (hw->phy.type == e1000_phy_82577) { + ret_val = hw->phy.ops.read_phy_reg_locked(hw, + HV_M_STATUS, + &status_reg); + if (ret_val) + goto release; + + status_reg &= HV_M_STATUS_LINK_UP | + HV_M_STATUS_AUTONEG_COMPLETE | + HV_M_STATUS_SPEED_MASK; + + if (status_reg == (HV_M_STATUS_LINK_UP | + HV_M_STATUS_AUTONEG_COMPLETE | + HV_M_STATUS_SPEED_1000)) + k1_enable = false; + } + + /* Link stall fix for link up */ + ret_val = hw->phy.ops.write_phy_reg_locked(hw, PHY_REG(770, 19), + 0x0100); + if (ret_val) + goto release; + + } else { + /* Link stall fix for link down */ + ret_val = hw->phy.ops.write_phy_reg_locked(hw, PHY_REG(770, 19), + 0x4100); + if (ret_val) + goto release; + } + + ret_val = e1000_configure_k1_ich8lan(hw, k1_enable); + +release: + hw->phy.ops.release_phy(hw); +out: + return ret_val; +} + +/** + * e1000_configure_k1_ich8lan - Configure K1 power state + * @hw: pointer to the HW structure + * @enable: K1 state to configure + * + * Configure the K1 power state based on the provided parameter. + * Assumes semaphore already acquired. + * + * Success returns 0, Failure returns -E1000_ERR_PHY (-2) + **/ +static s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable) +{ + s32 ret_val = 0; + u32 ctrl_reg = 0; + u32 ctrl_ext = 0; + u32 reg = 0; + u16 kmrn_reg = 0; + + ret_val = e1000e_read_kmrn_reg_locked(hw, + E1000_KMRNCTRLSTA_K1_CONFIG, + &kmrn_reg); + if (ret_val) + goto out; + + if (k1_enable) + kmrn_reg |= E1000_KMRNCTRLSTA_K1_ENABLE; + else + kmrn_reg &= ~E1000_KMRNCTRLSTA_K1_ENABLE; + + ret_val = e1000e_write_kmrn_reg_locked(hw, + E1000_KMRNCTRLSTA_K1_CONFIG, + kmrn_reg); + if (ret_val) + goto out; + + udelay(20); + ctrl_ext = er32(CTRL_EXT); + ctrl_reg = er32(CTRL); + + reg = ctrl_reg & ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100); + reg |= E1000_CTRL_FRCSPD; + ew32(CTRL, reg); + + ew32(CTRL_EXT, ctrl_ext | E1000_CTRL_EXT_SPD_BYPS); + udelay(20); + ew32(CTRL, ctrl_reg); + ew32(CTRL_EXT, ctrl_ext); + udelay(20); + +out: + return ret_val; +} + /** * e1000_oem_bits_config_ich8lan - SW-based LCD Configuration * @hw: pointer to the HW structure @@ -1030,10 +1168,20 @@ static s32 e1000_hv_phy_workarounds_ich8lan(struct e1000_hw *hw) ret_val = hw->phy.ops.acquire_phy(hw); if (ret_val) return ret_val; + hw->phy.addr = 1; - e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT, 0); + ret_val = e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT, 0); + if (ret_val) + goto out; hw->phy.ops.release_phy(hw); + /* + * Configure the K1 Si workaround during phy reset assuming there is + * link so that it disables K1 if link is in 1Gbps. + */ + ret_val = e1000_k1_gig_workaround_hv(hw, true); + +out: return ret_val; } @@ -2435,6 +2583,7 @@ static s32 e1000_get_bus_info_ich8lan(struct e1000_hw *hw) **/ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw) { + struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; u16 reg; u32 ctrl, icr, kab; s32 ret_val; @@ -2470,6 +2619,18 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw) ew32(PBS, E1000_PBS_16K); } + if (hw->mac.type == e1000_pchlan) { + /* Save the NVM K1 bit setting*/ + ret_val = e1000_read_nvm(hw, E1000_NVM_K1_CONFIG, 1, ®); + if (ret_val) + return ret_val; + + if (reg & E1000_NVM_K1_ENABLE) + dev_spec->nvm_k1_enabled = true; + else + dev_spec->nvm_k1_enabled = false; + } + ctrl = er32(CTRL); if (!e1000_check_reset_block(hw)) { @@ -2847,14 +3008,6 @@ static s32 e1000_get_link_up_info_ich8lan(struct e1000_hw *hw, u16 *speed, if (ret_val) return ret_val; - if ((hw->mac.type == e1000_pchlan) && (*speed == SPEED_1000)) { - ret_val = e1000e_write_kmrn_reg(hw, - E1000_KMRNCTRLSTA_K1_CONFIG, - E1000_KMRNCTRLSTA_K1_DISABLE); - if (ret_val) - return ret_val; - } - if ((hw->mac.type == e1000_ich8lan) && (hw->phy.type == e1000_phy_igp_3) && (*speed == SPEED_1000)) { diff --git a/drivers/net/e1000e/phy.c b/drivers/net/e1000e/phy.c index f9d33ab05e9..03175b3a2c9 100644 --- a/drivers/net/e1000e/phy.c +++ b/drivers/net/e1000e/phy.c @@ -95,13 +95,6 @@ static const u16 e1000_igp_2_cable_length_table[] = /* BM PHY Copper Specific Control 1 */ #define BM_CS_CTRL1 16 -/* BM PHY Copper Specific Status */ -#define BM_CS_STATUS 17 -#define BM_CS_STATUS_LINK_UP 0x0400 -#define BM_CS_STATUS_RESOLVED 0x0800 -#define BM_CS_STATUS_SPEED_MASK 0xC000 -#define BM_CS_STATUS_SPEED_1000 0x8000 - #define HV_MUX_DATA_CTRL PHY_REG(776, 16) #define HV_MUX_DATA_CTRL_GEN_TO_MAC 0x0400 #define HV_MUX_DATA_CTRL_FORCE_SPEED 0x0004 @@ -563,7 +556,7 @@ s32 e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data) } /** - * e1000_read_kmrn_reg_locked - Read kumeran register + * e1000e_read_kmrn_reg_locked - Read kumeran register * @hw: pointer to the HW structure * @offset: register offset to be read * @data: pointer to the read data @@ -572,7 +565,7 @@ s32 e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data) * information retrieved is stored in data. * Assumes semaphore already acquired. **/ -s32 e1000_read_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 *data) +s32 e1000e_read_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 *data) { return __e1000_read_kmrn_reg(hw, offset, data, true); } @@ -631,7 +624,7 @@ s32 e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data) } /** - * e1000_write_kmrn_reg_locked - Write kumeran register + * e1000e_write_kmrn_reg_locked - Write kumeran register * @hw: pointer to the HW structure * @offset: register offset to write to * @data: data to write at register offset @@ -639,7 +632,7 @@ s32 e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data) * Write the data to PHY register at the offset using the kumeran interface. * Assumes semaphore already acquired. **/ -s32 e1000_write_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 data) +s32 e1000e_write_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 data) { return __e1000_write_kmrn_reg(hw, offset, data, true); }