diff --git a/Documentation/fb/pxafb.txt b/Documentation/fb/pxafb.txt index ad94b5ca009..d143a0a749f 100644 --- a/Documentation/fb/pxafb.txt +++ b/Documentation/fb/pxafb.txt @@ -56,3 +56,87 @@ outputen:POLARITY pixclockpol:POLARITY pixel clock polarity 0 => falling edge, 1 => rising edge + + +Overlay Support for PXA27x and later LCD controllers +==================================================== + + PXA27x and later processors support overlay1 and overlay2 on-top of the + base framebuffer (although under-neath the base is also possible). They + support palette and no-palette RGB formats, as well as YUV formats (only + available on overlay2). These overlays have dedicated DMA channels and + behave in a similar way as a framebuffer. + + However, there are some differences between these overlay framebuffers + and normal framebuffers, as listed below: + + 1. overlay can start at a 32-bit word aligned position within the base + framebuffer, which means they have a start (x, y). This information + is encoded into var->nonstd (no, var->xoffset and var->yoffset are + not for such purpose). + + 2. overlay framebuffer is allocated dynamically according to specified + 'struct fb_var_screeninfo', the amount is decided by: + + var->xres_virtual * var->yres_virtual * bpp + + bpp = 16 -- for RGB565 or RGBT555 + = 24 -- for YUV444 packed + = 24 -- for YUV444 planar + = 16 -- for YUV422 planar (1 pixel = 1 Y + 1/2 Cb + 1/2 Cr) + = 12 -- for YUV420 planar (1 pixel = 1 Y + 1/4 Cb + 1/4 Cr) + + NOTE: + + a. overlay does not support panning in x-direction, thus + var->xres_virtual will always be equal to var->xres + + b. line length of overlay(s) must be on a 32-bit word boundary, + for YUV planar modes, it is a requirement for the component + with minimum bits per pixel, e.g. for YUV420, Cr component + for one pixel is actually 2-bits, it means the line length + should be a multiple of 16-pixels + + c. starting horizontal position (XPOS) should start on a 32-bit + word boundary, otherwise the fb_check_var() will just fail. + + d. the rectangle of the overlay should be within the base plane, + otherwise fail + + Applications should follow the sequence below to operate an overlay + framebuffer: + + a. open("/dev/fb[1-2]", ...) + b. ioctl(fd, FBIOGET_VSCREENINFO, ...) + c. modify 'var' with desired parameters: + 1) var->xres and var->yres + 2) larger var->yres_virtual if more memory is required, + usually for double-buffering + 3) var->nonstd for starting (x, y) and color format + 4) var->{red, green, blue, transp} if RGB mode is to be used + d. ioctl(fd, FBIOPUT_VSCREENINFO, ...) + e. ioctl(fd, FBIOGET_FSCREENINFO, ...) + f. mmap + g. ... + + 3. for YUV planar formats, these are actually not supported within the + framebuffer framework, application has to take care of the offsets + and lengths of each component within the framebuffer. + + 4. var->nonstd is used to pass starting (x, y) position and color format, + the detailed bit fields are shown below: + + 31 23 20 10 0 + +-----------------+---+----------+----------+ + | ... unused ... |FOR| XPOS | YPOS | + +-----------------+---+----------+----------+ + + FOR - color format, as defined by OVERLAY_FORMAT_* in pxafb.h + 0 - RGB + 1 - YUV444 PACKED + 2 - YUV444 PLANAR + 3 - YUV422 PLANAR + 4 - YUR420 PLANAR + + XPOS - starting horizontal position + YPOS - starting vertical position diff --git a/arch/arm/mach-pxa/include/mach/regs-lcd.h b/arch/arm/mach-pxa/include/mach/regs-lcd.h index aff3b876a7b..f82dcea792d 100644 --- a/arch/arm/mach-pxa/include/mach/regs-lcd.h +++ b/arch/arm/mach-pxa/include/mach/regs-lcd.h @@ -12,7 +12,8 @@ #define LCCR3 (0x00C) /* LCD Controller Control Register 3 */ #define LCCR4 (0x010) /* LCD Controller Control Register 4 */ #define LCCR5 (0x014) /* LCD Controller Control Register 5 */ -#define LCSR (0x038) /* LCD Controller Status Register */ +#define LCSR (0x038) /* LCD Controller Status Register 0 */ +#define LCSR1 (0x034) /* LCD Controller Status Register 1 */ #define LIIDR (0x03C) /* LCD Controller Interrupt ID Register */ #define TMEDRGBR (0x040) /* TMED RGB Seed Register */ #define TMEDCR (0x044) /* TMED Control Register */ @@ -25,6 +26,11 @@ #define FBR5 (0x110) /* DMA Channel 2 Frame Branch Register */ #define FBR6 (0x114) /* DMA Channel 2 Frame Branch Register */ +#define OVL1C1 (0x050) /* Overlay 1 Control Register 1 */ +#define OVL1C2 (0x060) /* Overlay 1 Control Register 2 */ +#define OVL2C1 (0x070) /* Overlay 2 Control Register 1 */ +#define OVL2C2 (0x080) /* Overlay 2 Control Register 2 */ + #define CMDCR (0x100) /* Command Control Register */ #define PRSR (0x104) /* Panel Read Status Register */ @@ -42,16 +48,12 @@ #define LCCR4_PAL_FOR_MASK (3 << 15) #define FDADR0 (0x200) /* DMA Channel 0 Frame Descriptor Address Register */ -#define FSADR0 (0x204) /* DMA Channel 0 Frame Source Address Register */ -#define FIDR0 (0x208) /* DMA Channel 0 Frame ID Register */ -#define LDCMD0 (0x20C) /* DMA Channel 0 Command Register */ #define FDADR1 (0x210) /* DMA Channel 1 Frame Descriptor Address Register */ -#define FSADR1 (0x214) /* DMA Channel 1 Frame Source Address Register */ -#define FIDR1 (0x218) /* DMA Channel 1 Frame ID Register */ -#define LDCMD1 (0x21C) /* DMA Channel 1 Command Register */ +#define FDADR2 (0x220) /* DMA Channel 2 Frame Descriptor Address Register */ +#define FDADR3 (0x230) /* DMA Channel 3 Frame Descriptor Address Register */ +#define FDADR4 (0x240) /* DMA Channel 4 Frame Descriptor Address Register */ +#define FDADR5 (0x250) /* DMA Channel 5 Frame Descriptor Address Register */ #define FDADR6 (0x260) /* DMA Channel 6 Frame Descriptor Address Register */ -#define FSADR6 (0x264) /* DMA Channel 6 Frame Source Address Register */ -#define FIDR6 (0x268) /* DMA Channel 6 Frame ID Register */ #define LCCR0_ENB (1 << 0) /* LCD Controller enable */ #define LCCR0_CMS (1 << 1) /* Color/Monochrome Display Select */ @@ -151,8 +153,22 @@ #define LCSR_RD_ST (1 << 11) /* read status */ #define LCSR_CMD_INT (1 << 12) /* command interrupt */ +#define LCSR1_IU(x) (1 << ((x) + 23)) /* Input FIFO underrun */ +#define LCSR1_BS(x) (1 << ((x) + 15)) /* Branch Status */ +#define LCSR1_EOF(x) (1 << ((x) + 7)) /* End of Frame Status */ +#define LCSR1_SOF(x) (1 << ((x) - 1)) /* Start of Frame Status */ + #define LDCMD_PAL (1 << 26) /* instructs DMA to load palette buffer */ +/* overlay control registers */ +#define OVLxC1_PPL(x) ((((x) - 1) & 0x3ff) << 0) /* Pixels Per Line */ +#define OVLxC1_LPO(x) ((((x) - 1) & 0x3ff) << 10) /* Number of Lines */ +#define OVLxC1_BPP(x) (((x) & 0xf) << 20) /* Bits Per Pixel */ +#define OVLxC1_OEN (1 << 31) /* Enable bit for Overlay */ +#define OVLxC2_XPOS(x) (((x) & 0x3ff) << 0) /* Horizontal Position */ +#define OVLxC2_YPOS(x) (((x) & 0x3ff) << 10) /* Vertical Position */ +#define OVL2C2_PFOR(x) (((x) & 0x7) << 20) /* Pixel Format */ + /* smartpanel related */ #define PRSR_DATA(x) ((x) & 0xff) /* Panel Data */ #define PRSR_A0 (1 << 8) /* Read Data Source */ diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig index 3f3ce13fef4..486d81ca02a 100644 --- a/drivers/video/Kconfig +++ b/drivers/video/Kconfig @@ -1817,6 +1817,11 @@ config FB_PXA If unsure, say N. +config FB_PXA_OVERLAY + bool "Support PXA27x/PXA3xx Overlay(s) as framebuffer" + default n + depends on FB_PXA && (PXA27x || PXA3xx) + config FB_PXA_SMARTPANEL bool "PXA Smartpanel LCD support" default n diff --git a/drivers/video/pxafb.c b/drivers/video/pxafb.c index 7935706a756..3a41ea10e8e 100644 --- a/drivers/video/pxafb.c +++ b/drivers/video/pxafb.c @@ -20,6 +20,16 @@ * * linux-arm-kernel@lists.arm.linux.org.uk * + * Add support for overlay1 and overlay2 based on pxafb_overlay.c: + * + * Copyright (C) 2004, Intel Corporation + * + * 2003/08/27: + * 2004/03/10: + * 2004/10/28: + * + * Copyright (C) 2006-2008 Marvell International Ltd. + * All Rights Reserved */ #include @@ -72,6 +82,8 @@ static int pxafb_activate_var(struct fb_var_screeninfo *var, struct pxafb_info *); static void set_ctrlr_state(struct pxafb_info *fbi, u_int state); static void setup_base_frame(struct pxafb_info *fbi, int branch); +static int setup_frame_dma(struct pxafb_info *fbi, int dma, int pal, + unsigned long offset, size_t size); static unsigned long video_mem_size = 0; @@ -581,6 +593,330 @@ static struct fb_ops pxafb_ops = { .fb_blank = pxafb_blank, }; +#ifdef CONFIG_FB_PXA_OVERLAY +static void overlay1fb_setup(struct pxafb_layer *ofb) +{ + int size = ofb->fb.fix.line_length * ofb->fb.var.yres_virtual; + unsigned long start = ofb->video_mem_phys; + setup_frame_dma(ofb->fbi, DMA_OV1, PAL_NONE, start, size); +} + +/* Depending on the enable status of overlay1/2, the DMA should be + * updated from FDADRx (when disabled) or FBRx (when enabled). + */ +static void overlay1fb_enable(struct pxafb_layer *ofb) +{ + int enabled = lcd_readl(ofb->fbi, OVL1C1) & OVLxC1_OEN; + uint32_t fdadr1 = ofb->fbi->fdadr[DMA_OV1] | (enabled ? 0x1 : 0); + + lcd_writel(ofb->fbi, enabled ? FBR1 : FDADR1, fdadr1); + lcd_writel(ofb->fbi, OVL1C2, ofb->control[1]); + lcd_writel(ofb->fbi, OVL1C1, ofb->control[0] | OVLxC1_OEN); +} + +static void overlay1fb_disable(struct pxafb_layer *ofb) +{ + uint32_t lccr5 = lcd_readl(ofb->fbi, LCCR5); + + lcd_writel(ofb->fbi, OVL1C1, ofb->control[0] & ~OVLxC1_OEN); + + lcd_writel(ofb->fbi, LCSR1, LCSR1_BS(1)); + lcd_writel(ofb->fbi, LCCR5, lccr5 & ~LCSR1_BS(1)); + lcd_writel(ofb->fbi, FBR1, ofb->fbi->fdadr[DMA_OV1] | 0x3); + + if (wait_for_completion_timeout(&ofb->branch_done, 1 * HZ) == 0) + pr_warning("%s: timeout disabling overlay1\n", __func__); + + lcd_writel(ofb->fbi, LCCR5, lccr5); +} + +static void overlay2fb_setup(struct pxafb_layer *ofb) +{ + int size, div = 1, pfor = NONSTD_TO_PFOR(ofb->fb.var.nonstd); + unsigned long start[3] = { ofb->video_mem_phys, 0, 0 }; + + if (pfor == OVERLAY_FORMAT_RGB || pfor == OVERLAY_FORMAT_YUV444_PACKED) { + size = ofb->fb.fix.line_length * ofb->fb.var.yres_virtual; + setup_frame_dma(ofb->fbi, DMA_OV2_Y, -1, start[0], size); + } else { + size = ofb->fb.var.xres_virtual * ofb->fb.var.yres_virtual; + switch (pfor) { + case OVERLAY_FORMAT_YUV444_PLANAR: div = 1; break; + case OVERLAY_FORMAT_YUV422_PLANAR: div = 2; break; + case OVERLAY_FORMAT_YUV420_PLANAR: div = 4; break; + } + start[1] = start[0] + size; + start[2] = start[1] + size / div; + setup_frame_dma(ofb->fbi, DMA_OV2_Y, -1, start[0], size); + setup_frame_dma(ofb->fbi, DMA_OV2_Cb, -1, start[1], size / div); + setup_frame_dma(ofb->fbi, DMA_OV2_Cr, -1, start[2], size / div); + } +} + +static void overlay2fb_enable(struct pxafb_layer *ofb) +{ + int pfor = NONSTD_TO_PFOR(ofb->fb.var.nonstd); + int enabled = lcd_readl(ofb->fbi, OVL2C1) & OVLxC1_OEN; + uint32_t fdadr2 = ofb->fbi->fdadr[DMA_OV2_Y] | (enabled ? 0x1 : 0); + uint32_t fdadr3 = ofb->fbi->fdadr[DMA_OV2_Cb] | (enabled ? 0x1 : 0); + uint32_t fdadr4 = ofb->fbi->fdadr[DMA_OV2_Cr] | (enabled ? 0x1 : 0); + + if (pfor == OVERLAY_FORMAT_RGB || pfor == OVERLAY_FORMAT_YUV444_PACKED) + lcd_writel(ofb->fbi, enabled ? FBR2 : FDADR2, fdadr2); + else { + lcd_writel(ofb->fbi, enabled ? FBR2 : FDADR2, fdadr2); + lcd_writel(ofb->fbi, enabled ? FBR3 : FDADR3, fdadr3); + lcd_writel(ofb->fbi, enabled ? FBR4 : FDADR4, fdadr4); + } + lcd_writel(ofb->fbi, OVL2C2, ofb->control[1]); + lcd_writel(ofb->fbi, OVL2C1, ofb->control[0] | OVLxC1_OEN); +} + +static void overlay2fb_disable(struct pxafb_layer *ofb) +{ + uint32_t lccr5 = lcd_readl(ofb->fbi, LCCR5); + + lcd_writel(ofb->fbi, OVL2C1, ofb->control[0] & ~OVLxC1_OEN); + + lcd_writel(ofb->fbi, LCSR1, LCSR1_BS(2)); + lcd_writel(ofb->fbi, LCCR5, lccr5 & ~LCSR1_BS(2)); + lcd_writel(ofb->fbi, FBR2, ofb->fbi->fdadr[DMA_OV2_Y] | 0x3); + lcd_writel(ofb->fbi, FBR3, ofb->fbi->fdadr[DMA_OV2_Cb] | 0x3); + lcd_writel(ofb->fbi, FBR4, ofb->fbi->fdadr[DMA_OV2_Cr] | 0x3); + + if (wait_for_completion_timeout(&ofb->branch_done, 1 * HZ) == 0) + pr_warning("%s: timeout disabling overlay2\n", __func__); +} + +static struct pxafb_layer_ops ofb_ops[] = { + [0] = { + .enable = overlay1fb_enable, + .disable = overlay1fb_disable, + .setup = overlay1fb_setup, + }, + [1] = { + .enable = overlay2fb_enable, + .disable = overlay2fb_disable, + .setup = overlay2fb_setup, + }, +}; + +static int overlayfb_open(struct fb_info *info, int user) +{ + struct pxafb_layer *ofb = (struct pxafb_layer *)info; + + /* no support for framebuffer console on overlay */ + if (user == 0) + return -ENODEV; + + /* allow only one user at a time */ + if (atomic_inc_and_test(&ofb->usage)) + return -EBUSY; + + /* unblank the base framebuffer */ + fb_blank(&ofb->fbi->fb, FB_BLANK_UNBLANK); + return 0; +} + +static int overlayfb_release(struct fb_info *info, int user) +{ + struct pxafb_layer *ofb = (struct pxafb_layer*) info; + + atomic_dec(&ofb->usage); + ofb->ops->disable(ofb); + + free_pages_exact(ofb->video_mem, ofb->video_mem_size); + ofb->video_mem = NULL; + ofb->video_mem_size = 0; + return 0; +} + +static int overlayfb_check_var(struct fb_var_screeninfo *var, + struct fb_info *info) +{ + struct pxafb_layer *ofb = (struct pxafb_layer *)info; + struct fb_var_screeninfo *base_var = &ofb->fbi->fb.var; + int xpos, ypos, pfor, bpp; + + xpos = NONSTD_TO_XPOS(var->nonstd); + ypos = NONSTD_TO_XPOS(var->nonstd); + pfor = NONSTD_TO_PFOR(var->nonstd); + + bpp = pxafb_var_to_bpp(var); + if (bpp < 0) + return -EINVAL; + + /* no support for YUV format on overlay1 */ + if (ofb->id == OVERLAY1 && pfor != 0) + return -EINVAL; + + /* for YUV packed formats, bpp = 'minimum bpp of YUV components' */ + switch (pfor) { + case OVERLAY_FORMAT_RGB: + bpp = pxafb_var_to_bpp(var); + if (bpp < 0) + return -EINVAL; + + pxafb_set_pixfmt(var, var_to_depth(var)); + break; + case OVERLAY_FORMAT_YUV444_PACKED: bpp = 24; break; + case OVERLAY_FORMAT_YUV444_PLANAR: bpp = 8; break; + case OVERLAY_FORMAT_YUV422_PLANAR: bpp = 4; break; + case OVERLAY_FORMAT_YUV420_PLANAR: bpp = 2; break; + default: + return -EINVAL; + } + + /* each line must start at a 32-bit word boundary */ + if ((xpos * bpp) % 32) + return -EINVAL; + + /* xres must align on 32-bit word boundary */ + var->xres = roundup(var->xres * bpp, 32) / bpp; + + if ((xpos + var->xres > base_var->xres) || + (ypos + var->yres > base_var->yres)) + return -EINVAL; + + var->xres_virtual = var->xres; + var->yres_virtual = max(var->yres, var->yres_virtual); + return 0; +} + +static int overlayfb_map_video_memory(struct pxafb_layer *ofb) +{ + struct fb_var_screeninfo *var = &ofb->fb.var; + int pfor = NONSTD_TO_PFOR(var->nonstd); + int size, bpp = 0; + + switch (pfor) { + case OVERLAY_FORMAT_RGB: bpp = var->bits_per_pixel; break; + case OVERLAY_FORMAT_YUV444_PACKED: bpp = 24; break; + case OVERLAY_FORMAT_YUV444_PLANAR: bpp = 24; break; + case OVERLAY_FORMAT_YUV422_PLANAR: bpp = 16; break; + case OVERLAY_FORMAT_YUV420_PLANAR: bpp = 12; break; + } + + ofb->fb.fix.line_length = var->xres_virtual * bpp / 8; + + size = PAGE_ALIGN(ofb->fb.fix.line_length * var->yres_virtual); + + /* don't re-allocate if the original video memory is enough */ + if (ofb->video_mem) { + if (ofb->video_mem_size >= size) + return 0; + + free_pages_exact(ofb->video_mem, ofb->video_mem_size); + } + + ofb->video_mem = alloc_pages_exact(size, GFP_KERNEL | __GFP_ZERO); + if (ofb->video_mem == NULL) + return -ENOMEM; + + ofb->video_mem_phys = virt_to_phys(ofb->video_mem); + ofb->video_mem_size = size; + + ofb->fb.fix.smem_start = ofb->video_mem_phys; + ofb->fb.fix.smem_len = ofb->fb.fix.line_length * var->yres_virtual; + ofb->fb.screen_base = ofb->video_mem; + return 0; +} + +static int overlayfb_set_par(struct fb_info *info) +{ + struct pxafb_layer *ofb = (struct pxafb_layer *)info; + struct fb_var_screeninfo *var = &info->var; + int xpos, ypos, pfor, bpp, ret; + + ret = overlayfb_map_video_memory(ofb); + if (ret) + return ret; + + bpp = pxafb_var_to_bpp(var); + xpos = NONSTD_TO_XPOS(var->nonstd); + ypos = NONSTD_TO_XPOS(var->nonstd); + pfor = NONSTD_TO_PFOR(var->nonstd); + + ofb->control[0] = OVLxC1_PPL(var->xres) | OVLxC1_LPO(var->yres) | + OVLxC1_BPP(bpp); + ofb->control[1] = OVLxC2_XPOS(xpos) | OVLxC2_YPOS(ypos); + + if (ofb->id == OVERLAY2) + ofb->control[1] |= OVL2C2_PFOR(pfor); + + ofb->ops->setup(ofb); + ofb->ops->enable(ofb); + return 0; +} + +static struct fb_ops overlay_fb_ops = { + .owner = THIS_MODULE, + .fb_open = overlayfb_open, + .fb_release = overlayfb_release, + .fb_check_var = overlayfb_check_var, + .fb_set_par = overlayfb_set_par, +}; + +static void __devinit init_pxafb_overlay(struct pxafb_info *fbi, + struct pxafb_layer *ofb, int id) +{ + sprintf(ofb->fb.fix.id, "overlay%d", id + 1); + + ofb->fb.fix.type = FB_TYPE_PACKED_PIXELS; + ofb->fb.fix.xpanstep = 0; + ofb->fb.fix.ypanstep = 1; + + ofb->fb.var.activate = FB_ACTIVATE_NOW; + ofb->fb.var.height = -1; + ofb->fb.var.width = -1; + ofb->fb.var.vmode = FB_VMODE_NONINTERLACED; + + ofb->fb.fbops = &overlay_fb_ops; + ofb->fb.flags = FBINFO_FLAG_DEFAULT; + ofb->fb.node = -1; + ofb->fb.pseudo_palette = NULL; + + ofb->id = id; + ofb->ops = &ofb_ops[id]; + atomic_set(&ofb->usage, 0); + ofb->fbi = fbi; + init_completion(&ofb->branch_done); +} + +static int __devinit pxafb_overlay_init(struct pxafb_info *fbi) +{ + int i, ret; + + for (i = 0; i < 2; i++) { + init_pxafb_overlay(fbi, &fbi->overlay[i], i); + ret = register_framebuffer(&fbi->overlay[i].fb); + if (ret) { + dev_err(fbi->dev, "failed to register overlay %d\n", i); + return ret; + } + } + + /* mask all IU/BS/EOF/SOF interrupts */ + lcd_writel(fbi, LCCR5, ~0); + + /* place overlay(s) on top of base */ + fbi->lccr0 |= LCCR0_OUC; + pr_info("PXA Overlay driver loaded successfully!\n"); + return 0; +} + +static void __devexit pxafb_overlay_exit(struct pxafb_info *fbi) +{ + int i; + + for (i = 0; i < 2; i++) + unregister_framebuffer(&fbi->overlay[i].fb); +} +#else +static inline void pxafb_overlay_init(struct pxafb_info *fbi) {} +static inline void pxafb_overlay_exit(struct pxafb_info *fbi) {} +#endif /* CONFIG_FB_PXA_OVERLAY */ + /* * Calculate the PCD value from the clock rate (in picoseconds). * We take account of the PPCR clock setting. @@ -660,7 +996,7 @@ unsigned long pxafb_get_hsync_time(struct device *dev) EXPORT_SYMBOL(pxafb_get_hsync_time); static int setup_frame_dma(struct pxafb_info *fbi, int dma, int pal, - unsigned int offset, size_t size) + unsigned long start, size_t size) { struct pxafb_dma_descriptor *dma_desc, *pal_desc; unsigned int dma_desc_off, pal_desc_off; @@ -671,7 +1007,7 @@ static int setup_frame_dma(struct pxafb_info *fbi, int dma, int pal, dma_desc = &fbi->dma_buff->dma_desc[dma]; dma_desc_off = offsetof(struct pxafb_dma_buff, dma_desc[dma]); - dma_desc->fsadr = fbi->video_mem_phys + offset; + dma_desc->fsadr = start; dma_desc->fidr = 0; dma_desc->ldcmd = size; @@ -705,14 +1041,14 @@ static void setup_base_frame(struct pxafb_info *fbi, int branch) { struct fb_var_screeninfo *var = &fbi->fb.var; struct fb_fix_screeninfo *fix = &fbi->fb.fix; - unsigned int nbytes, offset; - int dma, pal, bpp = var->bits_per_pixel; + int nbytes, dma, pal, bpp = var->bits_per_pixel; + unsigned long offset; dma = DMA_BASE + (branch ? DMA_MAX : 0); pal = (bpp >= 16) ? PAL_NONE : PAL_BASE + (branch ? PAL_MAX : 0); nbytes = fix->line_length * var->yres; - offset = fix->line_length * var->yoffset; + offset = fix->line_length * var->yoffset + fbi->video_mem_phys; if (fbi->lccr0 & LCCR0_SDS) { nbytes = nbytes / 2; @@ -1090,8 +1426,9 @@ static void pxafb_disable_controller(struct pxafb_info *fbi) static irqreturn_t pxafb_handle_irq(int irq, void *dev_id) { struct pxafb_info *fbi = dev_id; - unsigned int lccr0, lcsr = lcd_readl(fbi, LCSR); + unsigned int lccr0, lcsr, lcsr1; + lcsr = lcd_readl(fbi, LCSR); if (lcsr & LCSR_LDD) { lccr0 = lcd_readl(fbi, LCCR0); lcd_writel(fbi, LCCR0, lccr0 | LCCR0_LDM); @@ -1102,8 +1439,18 @@ static irqreturn_t pxafb_handle_irq(int irq, void *dev_id) if (lcsr & LCSR_CMD_INT) complete(&fbi->command_done); #endif - lcd_writel(fbi, LCSR, lcsr); + +#ifdef CONFIG_FB_PXA_OVERLAY + lcsr1 = lcd_readl(fbi, LCSR1); + if (lcsr1 & LCSR1_BS(1)) + complete(&fbi->overlay[0].branch_done); + + if (lcsr1 & LCSR1_BS(2)) + complete(&fbi->overlay[1].branch_done); + + lcd_writel(fbi, LCSR1, lcsr1); +#endif return IRQ_HANDLED; } @@ -1802,6 +2149,8 @@ static int __devinit pxafb_probe(struct platform_device *dev) goto failed_free_cmap; } + pxafb_overlay_init(fbi); + #ifdef CONFIG_CPU_FREQ fbi->freq_transition.notifier_call = pxafb_freq_transition; fbi->freq_policy.notifier_call = pxafb_freq_policy; @@ -1852,6 +2201,7 @@ static int __devexit pxafb_remove(struct platform_device *dev) info = &fbi->fb; + pxafb_overlay_exit(fbi); unregister_framebuffer(info); pxafb_disable_controller(fbi); diff --git a/drivers/video/pxafb.h b/drivers/video/pxafb.h index ae3cbc1ca64..2353521c5c8 100644 --- a/drivers/video/pxafb.h +++ b/drivers/video/pxafb.h @@ -64,6 +64,47 @@ struct pxafb_dma_buff { struct pxafb_dma_descriptor dma_desc[DMA_MAX * 2]; }; +enum { + OVERLAY1, + OVERLAY2, +}; + +enum { + OVERLAY_FORMAT_RGB = 0, + OVERLAY_FORMAT_YUV444_PACKED, + OVERLAY_FORMAT_YUV444_PLANAR, + OVERLAY_FORMAT_YUV422_PLANAR, + OVERLAY_FORMAT_YUV420_PLANAR, +}; + +#define NONSTD_TO_XPOS(x) (((x) >> 0) & 0x3ff) +#define NONSTD_TO_YPOS(x) (((x) >> 10) & 0x3ff) +#define NONSTD_TO_PFOR(x) (((x) >> 20) & 0x7) + +struct pxafb_layer; + +struct pxafb_layer_ops { + void (*enable)(struct pxafb_layer *); + void (*disable)(struct pxafb_layer *); + void (*setup)(struct pxafb_layer *); +}; + +struct pxafb_layer { + struct fb_info fb; + int id; + atomic_t usage; + uint32_t control[2]; + + struct pxafb_layer_ops *ops; + + void __iomem *video_mem; + unsigned long video_mem_phys; + size_t video_mem_size; + struct completion branch_done; + + struct pxafb_info *fbi; +}; + struct pxafb_info { struct fb_info fb; struct device *dev; @@ -114,6 +155,10 @@ struct pxafb_info { struct task_struct *smart_thread; #endif +#ifdef CONFIG_FB_PXA_OVERLAY + struct pxafb_layer overlay[2]; +#endif + #ifdef CONFIG_CPU_FREQ struct notifier_block freq_transition; struct notifier_block freq_policy;